1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your new Teka CNL2002 Kitchen Hood Filter Kit. These stainless steel metal filters are designed as replacement parts for various kitchen hood models, primarily Teka CNL2002 series, and select Kuppersbusch and Smeg models. Please read this manual thoroughly before proceeding with installation or maintenance to ensure safe and correct usage.
2. Safety Information
- Always disconnect power to the range hood before attempting any installation, removal, or cleaning of filters.
- Handle filters carefully to avoid cuts from sharp edges.
- Ensure filters are securely latched in place before restoring power to the hood.
- Keep packaging materials away from children.
3. Package Contents
Your Teka CNL2002 Kitchen Hood Filter Kit includes:
- One (1) Fixed Metal Filter
- One (1) Mobile Metal Filter
The image below illustrates the two filters included in the kit.

4. Specifications
Fixed Filter Measurements:
- Width: 547 mm
- Length: 209 mm
- Distance between upper tabs: 494 mm
- Distance between lower tabs: 268 mm
Mobile Filter Measurements:
- Width: 511 mm
- Length: 184 mm
- Distance between upper tabs: 456 mm
- Distance between lower tabs: 268 mm
Original Part Codes:
- 61836020
- 61836021
5. Compatibility
This filter kit is compatible with the following extractor hood brands and models:
Kuppersbusch Extractor Hoods:
- EDIP600W
- EDIP64000E
- EDIP64001E
Smeg Extractor Hoods:
- KSET610X
- KSET910X
Teka Extractor Hoods:
- CML-2002VR01
- CNL1 2002
- CNL1-1001
- CNL1-2002
- CNL1001
- CNL1001BLANCA
- CNL1001INOX
- CNL1001MARRON
- CNL1001NEGRA
- CNL11001BANCA
- CNL11001I
- CNL11001INOX
- CNL11001NEGRA
- CNL12002BLANCA
- CNL12002INOX
- CNL12002NEGRA
- CNL13000INOX
- CNL2002
- CNL2002VR02
- CNL2002BLANCA
- CNL2002INOX
- CNL2002VR01
- CNL3000
- CNL3000INOX
- CNL3000INOXGER
- CNL3000INOXHP
- CNL6610INOX
- CNX600
- CNX6000INOX
- CNX6000INOXGER
- CNX6000INOXHP
6. Setup and Installation
Follow these steps to replace your kitchen hood filters:
- Disconnect Power: Ensure your range hood is completely turned off and unplugged from the power outlet to prevent electrical hazards.
- Locate Old Filters: Identify the existing grease filters in your range hood. They are typically located on the underside of the hood.
- Release Latches: Most filters are held in place by spring-loaded latches or clips. Gently push or pull these to release the filter.
- Remove Old Filters: Carefully slide or pull out the old filters. Be prepared for grease residue.
- Insert New Filters: Orient the new fixed and mobile filters correctly. Align the tabs on the new filters with the slots or grooves in the hood.
- Secure Filters: Push the new filters into place until the latches or clips engage and hold them securely. Give them a gentle tug to ensure they are firm.
- Restore Power: Once both filters are securely installed, plug the range hood back into the power outlet and turn it on.
7. Operating Instructions
Once installed, the filters operate passively as part of your kitchen hood's ventilation system. Ensure your hood is turned on during cooking to effectively capture grease and odors. Regularly check the filters for grease buildup to maintain optimal performance.
8. Maintenance
To ensure the longevity and efficiency of your kitchen hood filters, regular cleaning is essential:
- Cleaning Frequency: Filters should be cleaned every 3-6 weeks, depending on cooking frequency and type.
- Method 1 (Dishwasher): Most metal grease filters are dishwasher safe. Place them in the dishwasher, preferably on a hot cycle, without other dishes to avoid grease transfer.
- Method 2 (Hand Wash): For hand washing, soak the filters in hot water with a strong degreasing detergent. Use a non-abrasive brush to gently scrub away grease and residue. Rinse thoroughly and allow to air dry completely before re-installing.
- Avoid Abrasives: Do not use abrasive cleaners, steel wool, or harsh chemicals, as these can damage the filter material.
9. Troubleshooting
Filter Does Not Fit:
- Double-check the model number of your range hood against the compatibility list in Section 5.
- Verify the measurements of your existing filters against the specifications in Section 4. Slight variations can occur, but significant differences indicate an incorrect filter.
- Ensure you are attempting to install the correct filter (fixed vs. mobile) in its designated position.
Reduced Airflow/Poor Performance:
- Ensure the filters are clean. Heavily soiled filters can restrict airflow. Refer to Section 8 for cleaning instructions.
- Verify that the filters are installed correctly and securely latched, allowing no gaps for air to bypass them.
10. User Tips
No specific user tips were available from reviews or Q&A for this product. However, general advice for kitchen hood filters includes:
- For very heavy cooking, consider cleaning your filters more frequently than recommended.
- Always allow filters to dry completely before re-installing to prevent moisture buildup in the hood.
11. Warranty and Support
For any questions regarding the product, warranty information, or technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.