1. Introduction
The LAUNCH X431 i-TPMS is a professional Tire Pressure Monitoring System (TPMS) service tool designed to work with specific LAUNCH diagnostic tools or Android smartphones equipped with the i-TPMS app. It enables comprehensive TPMS functions including sensor activation, reading, learning, and programming for both 315MHz and 433MHz sensors.
Video: LAUNCH i-TPMS Product Overview
2. Safety Precautions
Please read and follow all safety warnings and instructions to prevent electric shock, fire, or serious injury. Keep this manual for future reference.
- The device contains no user-serviceable parts. Servicing should only be performed by qualified personnel using identical replacement parts. Disassembly voids the warranty.
- The device contains an internal Lithium Polymer battery. Do not disassemble, crush, pierce, or dispose of the battery in fire or water to avoid explosion or hazardous chemical release.
- This product is not a toy; keep away from children.
- Do not expose the device to rain or wet conditions.
- Do not place the device on unstable surfaces.
- Never leave the device unattended during charging. Place it on a non-flammable surface.
- Handle with care. If dropped, check for damage before use.
- When testing a vehicle, use wheel blocks and never leave the vehicle unattended.
- Do not operate the tool in explosive atmospheres or near flammable liquids, gases, or heavy dust.
- Keep the device dry, clean, and free from oil, water, or grease. Clean with a mild detergent on a clean cloth.
- Individuals with pacemakers should consult their physician before use, as electromagnetic fields may cause interference.
- Use the device only with the specific diagnostic tool loaded with the TPMS module and the i-TPMS app.
- Do not install programmed TPMS sensors in damaged wheels.
- When programming a sensor, avoid placing the device close to multiple sensors simultaneously to prevent programming failure.
- This manual cannot cover all possible conditions; common sense and caution are essential for safe operation.
3. FCC Statement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
4. Components & Controls
The i-TPMS device features a user-friendly design with essential controls and a display screen.

Image: LAUNCH i-TPMS Device Front View with Controls
Device Layout:
- Charging LED: Red indicates charging, Green indicates fully charged.
- UP Button: Navigates up or increases values.
- DOWN Button: Navigates down or decreases values.
- Charging Port: Used for connecting the charging cable.
- Sensor Slot: Insert the sensor here for activation and programming.
- Display Screen: Shows device status and menu options.
- POWER Button: Turns the tool on/off.
- OK (Confirm) Button: Confirms selections or actions.
5. Technical Specifications
| Parameter | Specification |
|---|---|
| Screen | 1.77 inch |
| Input Voltage | DC 5V |
| Dimensions (L x W x H) | 205mm x 57mm x 25.5mm (8.07 x 2.24 x 1.00 inches) |
| Item Weight | 0.6 kg (1.32 lbs) |
| Working Temperature | -10°C to 50°C (14°F to 122°F) |
| Storage Temperature | -20°C to 60°C (-4°F to 140°F) |
| Wireless Support | Bluetooth |
| Batteries Included | Yes |
| External Testing Certification | CE |
| Software Version | 2026 Version |
| Hardware Version | 2026 Version |
6. Accessories Included
Upon opening the package, please verify the presence of the following components. Note that accessories may vary slightly by region.
- i-TPMS Device
- Charging Cable
- User Manual (this document)

Image: i-TPMS Device and Included Accessories
7. Initial Use & Setup
7.1. Charging & Powering On
- Connect one end of the charging cable to the i-TPMS charging port and the other end to an external power adapter (not included).
- Plug the power adapter into an AC outlet. The Charging LED will illuminate red during charging and turn green when fully charged.
- Press the POWER button to turn on the device. A beep will sound, and the screen will light up.
7.2. Button Operations
- UP/DOWN Buttons: Used to switch between different tire positions or navigate menus.
- POWER Button: Press for approximately 3 seconds to turn the device on/off.
- Screen On/Hibernate: Press the POWER button once to enter hibernate mode.
- Auto Power Off: If the device is not charging and no operation is performed for 30 minutes, it will automatically power off. If charging and no operation for 5 minutes, it will enter hibernate mode.
- OK Button: Confirms the current operation or selection.
7.3. i-TPMS App Download (Android Smartphone Users)
For Android smartphone users, scan the QR code on the back of the i-TPMS device or the one below to download and install the i-TPMS app.

Image: QR Code for i-TPMS App Download
7.4. Getting Started Workflow
Follow these steps for initial use with a diagnostic tool or smartphone:
- Enter "TPMS" or "i-TPMS" on the diagnostic tool/smartphone.
- Search for and connect to the i-TPMS device via Bluetooth. (Ensure i-TPMS is powered on. If firmware is outdated, it will update automatically.)
- Select the target region.
- Select the vehicle manufacturer.
- Select the vehicle model and year.
- Select the desired TPMS function (e.g., Activation, Programming, Learning, Diagnosis).
- Follow on-screen instructions to proceed with the selected function.
Note: For indirect TPMS vehicles, only the Learning function is supported. For direct TPMS vehicles, functions generally include Activation, Programming, Learning, and Diagnosis. Available functions may vary by vehicle and app version.

Image: i-TPMS Device with Phone App Interface
8. Operating Instructions
The i-TPMS tool performs various TPMS operations. The following sections detail these functions.

Image: TPMS Activation, Relearn, Programming, Diagnostic Workflow
8.1. Activate Sensor
This function allows you to activate TPMS sensors to view real-time sensor data such as sensor ID, tire pressure, tire frequency, tire temperature, and battery condition.
- The tool will test TPMS in a sequence: Front Left (FL), Front Right (FR), Rear Right (RR), Rear Left (LR), and SPARE (if applicable). Use the UP/DOWN buttons to select the desired wheel.
- For universal sensors, place the i-TPMS alongside the valve stem, point towards the sensor, and press the OK button.
- Upon successful activation and decoding, the i-TPMS will vibrate slightly, and the screen will display the sensor data.

Image: Activating a TPMS Sensor
Notes:
- For early magnet-activated sensors, place the magnet over the stem, then place the i-TPMS alongside the valve stem.
- If the TPMS sensor requires tire deflation (around 10PSI), deflate the tire and place the i-TPMS alongside the stem while pressing the OK button.
8.2. Program Sensor
This function programs sensor data to a specific brand sensor, allowing replacement of faulty or low-battery sensors. It is primarily for LAUNCH-branded sensors.
Note: Do not place the device close to several sensors at the same time during programming, as this may cause programming failure.

Image: TPMS Sensor Programming Methods
Method 1: Auto Create
Used when the original sensor ID cannot be obtained. The i-TPMS creates a random ID based on the test vehicle.
- Select the wheel to be programmed on the screen.
- Insert a sensor into the i-TPMS sensor slot.
- Tap "Auto" to create a new random sensor ID.
- Tap "Program" to write the new ID to the sensor.
Note: If Auto Create is used, a TPMS Relearn operation is required after programming all sensors.
Method 2: Manual Create
Allows manual entry of a sensor ID (random or original, if available).
- Select the wheel to be programmed on the screen.
- Insert a sensor into the i-TPMS sensor slot.
- Tap "Manual".
- Use the on-screen virtual keypad to input the sensor ID and tap OK.
- Follow on-screen prompts to write the ID to the sensor.
Notes:
- Do not enter the same ID for each sensor.
- If a random ID is entered, a TPMS Relearn operation is required. If the original ID is entered, Relearn is not needed.
- If the vehicle does not support the Learn function, manually enter the original sensor ID or trigger the original sensor at the activation screen to get its information before programming.
Method 3: Copy by Activation
Copies retrieved original sensor data to a LAUNCH-branded sensor after the original sensor is triggered.
- From the activation screen, select the specific wheel position and trigger the original sensor. The retrieved information will be displayed.
- Insert a sensor into the i-TPMS sensor slot.
- Tap "Copy by Activation".
- Tap "Program" to write the copied sensor data to the sensor.
Note: Once programmed with Copy, the sensor can be installed directly in the wheel, and the TPMS warning light should turn off.
Method 4: Copy by OBD
Writes saved sensor information to the LAUNCH sensor after performing Read ECU ID. This requires a connection to the vehicle's DLC port.
- Connect the tool to the vehicle's DLC port.
- Tap "Read ECU ID" to view sensor IDs and positions.
- Insert a new sensor into the i-TPMS sensor slot, select the desired wheel position, and tap "Copy by OBD".
- Tap "Program" to write the copied sensor data to the sensor.
8.3. TPMS Relearning
This function writes newly programmed sensor IDs into the vehicle's ECU for sensor recognition, necessary when new sensor IDs differ from those stored in the ECU.

Image: TPMS Relearn Process via OBD
Method 1: Static Learning
Requires placing the vehicle into a learning/retraining mode and following on-screen prompts.
Method 2: Self-Learning
For some vehicles, the learning function can be completed by driving the vehicle. Follow on-screen learning steps.
Method 3: Relearn by OBD
This function uses the diagnostic tool to write sensor IDs to the TPMS module.
- Activate all sensors.
- Use the diagnostic tool with the included VCI (Vehicle Communication Interface) to complete the learning steps following on-screen instructions.
8.4. Diagnose Tire Pressure Fault
The i-TPMS tool can read and clear fault codes related to the TPMS system.

Image: Reading and Clearing TPMS Fault Codes
9. Troubleshooting
Here are some frequently asked questions and their solutions:
Q: Why does my i-TPMS always stay on the welcome screen?
A: If the device continuously displays the welcome screen, it means it is not in TPMS function mode. When the diagnostic tool performs a TPMS function, the i-TPMS device will automatically switch to the corresponding function mode.
Q: Can I set the system language of my i-TPMS?
A: The language of the i-TPMS varies with the system language of the connected diagnostic tool/smartphone. Currently, only English and Simplified Chinese are available. If the connected device's language is non-Chinese, the i-TPMS will default to English.
Q: My i-TPMS does not respond.
A: Check the following:
- Is the device successfully connected wirelessly to the diagnostic tool/smartphone?
- Is the device powered on?
- Is the device damaged or defective?
Q: Why does my i-TPMS automatically power off?
A: Check the following:
- Is the device fully discharged?
- If not charging and no operation is performed for 30 minutes, it will automatically power off to conserve battery.
Q: My i-TPMS cannot trigger a sensor.
A: Check the following:
- Is the device damaged or defective?
- Is the sensor, module, or ECU itself damaged or defective?
- Does the vehicle actually have a sensor? A metal valve stem does not guarantee a sensor is present. Be aware of Schrader rubber-style snap-in stems used on TPMS systems.
- The device may require a firmware upgrade.
Q: What to do if my i-TPMS encountered some unexpected bugs?
A: A firmware upgrade may be required. On the TPMS version selection screen, tap "Firmware Update" to upgrade it.
10. User Tips
- Ensure the i-TPMS device is fully charged before use, as it may arrive discharged.
- If the device doesn't immediately recognize sensors, allow several tens of seconds for detection.
- For programming, if a specific car brand isn't listed, try selecting the sensor type from the general list (OE Query) using its catalog number.
- The device works well with both original car sensors and LAUNCH-branded sensors for programming and activation.
- Firmware updates are crucial for optimal performance and bug fixes; ensure your device is updated via the app.
- The i-TPMS is designed to work in conjunction with a compatible LAUNCH scanner (like X431 Pro or PAD series) or the i-TPMS smartphone app, not as a standalone device for all functions.
11. Warranty & Support
The LAUNCH X431 i-TPMS comes with a 1-year warranty from the date of purchase.
For technical support, please refer to the contact information provided by your seller or the official LAUNCH support channels.