Taidacent TDJLRS485ANALOG

Contents

Taidacent Multi Channel PLC Analog I/O Input to RS485 Modbus RTU TCP Converter Module

Model: TDJLRS485ANALOG

1. Introduction

The Taidacent Multi Channel PLC Analog I/O Input to RS485 Modbus RTU TCP Converter Module is designed to convert analog signals from various sensors into a standard Modbus-RTU communication protocol for seamless integration with PLCs, industrial control instruments, and configuration software. This module offers robust performance with industrial-grade design, including overvoltage and overcurrent protection, ensuring high reliability and strong anti-interference capabilities.

2. Features

  • Analog Signal Conversion: Collects up to two analog signals (4-20mA, 0-10V, 0-5V) and converts them to RS485 Modbus-RTU protocol.
  • Modbus-RTU Protocol: Adopts standard Modbus-RTU protocol, allowing address and baud rate configuration via upper computer software.
  • Industrial Design: Built to industrial standards with overvoltage protection, overcurrent protection, and strong anti-interference.
  • Extended Communication: Supports a maximum RS485 communication distance of up to 2000 meters.
  • Versatile Connectivity: Directly connectable to PLCs, industrial control instruments, and configuration systems.
  • High Resolution: Offers 10-bit or 12-bit AD conversion resolution (optional).

3. Specifications

ParameterValue
Model NumberTDJLRS485ANALOG
OriginMainland China
Power Supply10~30V DC
Power Consumption0.4W
Number of Input Channels1 or 2 (optional)
AD Conversion Resolution10-bit or 12-bit (optional)
Acquisition Signal Types4~20mA, 0~5V, 0~10V (optional)
Storage Environment Temperature-40℃~60℃
Input Impedance (4~20mA)≤200 ohm
Input Impedance (0~5V/0-10V)≥10Kohm
Dimensions (L x W x H)96mm x 50mm x 31mm (approx.)
Weight0.3 kg (approx.)

4. Product Overview

The module features clearly labeled terminals for easy connection of analog inputs, sensor power, RS485 communication, and module power. Its compact design allows for flexible installation in various industrial environments.

Front view of the Taidacent PLC Analog I/O Converter Module, showing input and output terminals and protection indicators.

Figure 1: Front view of the converter module, highlighting the IN1, IN0, GND, VCC terminals for analog input and sensor power, and B-, A+, GND, VCC terminals for RS485 communication and module power. Chinese text indicates overvoltage, overcurrent protection, and anti-interference features.

Side view of the Taidacent PLC Analog I/O Converter Module with dimensions.

Figure 2: The side view of the module illustrates its physical dimensions: 96mm length, 50mm width, and 31mm height.

5. Setup and Wiring

Before connecting, ensure the power supply is off. Refer to the wiring diagram below for correct connections.

Top view of the Taidacent PLC Analog I/O Converter Module with clearly labeled wiring terminals.

Figure 3: Top view of the module with all terminals explicitly labeled for wiring.

5.1 Terminal Connections

  • Analog Inputs (Right Side):
    • IN1: Analog Input Channel 1
    • IN0: Analog Input Channel 2
    • VCC: Sensor Power Output (+)
    • GND: Sensor Power Output (-)
  • RS485 & Module Power (Left Side):
    • B-: RS485 Data Line B (-)
    • A+: RS485 Data Line A (+)
    • GND: Module Power Ground (-)
    • VCC: Module Power Input (+) (10-30V DC)

5.2 System Connection Example

The module can be integrated into a larger system as shown in the diagram below, connecting multiple modules to a central computer via RS485.

System connection diagram showing multiple Taidacent converter modules connected via RS485 to a computer and various sensors.

Figure 4: A typical system setup where multiple converter modules are connected via an RS485 bus to a central computer, each interfacing with different analog sensors.

6. Operating Instructions

Once wired, power on the module. The module will begin converting analog signals to Modbus-RTU data. Communication with a host device (PLC, PC) is established via the RS485 interface.

6.1 Modbus Configuration

The module's Modbus address and baud rate can be configured using dedicated upper computer software. This software allows you to set parameters to match your existing Modbus network. Consult the software's documentation for detailed instructions on changing these settings.

6.2 Data Acquisition

The host device can read the converted analog values by sending Modbus-RTU commands to the module's configured address. The specific Modbus registers for reading analog input data will be detailed in the module's programming guide (not provided in this manual).

7. Maintenance

The module is designed for industrial environments and requires minimal maintenance. Ensure the following:

  • Keep the module clean and free from dust and debris.
  • Ensure proper ventilation to prevent overheating.
  • Regularly check wiring connections for tightness and integrity.
  • Avoid exposing the module to extreme temperatures or humidity outside its specified operating range.

8. Troubleshooting

ProblemPossible CauseSolution
No communication via RS485Incorrect wiring (A+/B- reversed), incorrect Modbus address, incorrect baud rate, power supply issue, faulty RS485 converter.Verify A+/B- wiring. Check Modbus address and baud rate settings in software. Confirm power supply is within 10-30V DC. Test RS485 converter.
Incorrect analog readingsSensor not connected correctly, wrong input type selected (e.g., 4-20mA sensor connected to 0-5V input), sensor fault, module fault.Check sensor wiring to IN1/IN0 and sensor power. Ensure the module is configured for the correct analog input type (4-20mA, 0-5V, or 0-10V). Test the sensor independently.
Module not powering onNo power supply, incorrect voltage, reversed polarity.Verify power supply connection to VCC/GND terminals. Ensure voltage is within 10-30V DC and polarity is correct.
Intermittent communicationElectromagnetic interference (EMI), loose connections, ground loops.Ensure proper shielding for RS485 cables. Check all connections. Implement proper grounding practices.

9. User Tips

  • Baud Rate Configuration: Many users inquire about changing the baud rate. This is typically done through the manufacturer's provided configuration software. Ensure you have the correct software version and drivers for your operating system.
  • Analog Input Type: Double-check that the module's configuration matches the type of analog sensor you are connecting (e.g., 4-20mA, 0-5V, or 0-10V) to ensure accurate readings.
  • RS485 Termination: For longer RS485 bus lengths or systems with multiple devices, consider using termination resistors at both ends of the bus to prevent signal reflections and ensure stable communication.

10. Warranty and Support

For warranty information, technical support, or further assistance, please contact your vendor or the manufacturer directly. Keep your purchase receipt and model number (TDJLRS485ANALOG) handy when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.