Hobbywing 5L Brushless Water Pump V1

Contents

Hobbywing Combo Pump 5L Brushless Water Pump V1 Instruction Manual

Model: 5L Brushless Water Pump V1

Introduction

This manual provides essential information for the safe and efficient operation of your Hobbywing Combo Pump 5L Brushless Water Pump V1. This high-performance diaphragm pump is specifically designed for demanding applications such as plant agriculture and UAV drone spraying, offering reliable and consistent fluid delivery. Please read this manual thoroughly before installation and use.

Specifications

Hobbywing 5L Brushless Water Pump with key specifications overlaid

Figure 1: Hobbywing 5L Brushless Water Pump with key specifications.

FeatureSpecification
Operating Voltage12-14S (DC44-60.9V)
Working Current<2A
Weight388g (approx. 338g without wire)
Water Inlet Diameter10.5mm
Water Outlet Diameter6.5mm
Rated Power60W
Opening Flow5L/min
Dimensions (L*W*H)123*76*52mm
Working Pressure0.35Mpa
Protection LevelIP67
Fixed PWM Throttle Stroke110-1940US
MaterialMetal
Quantity1 pcs
For Vehicle TypeAirplanes
UseVehicles & Remote Control Toys

Setup

1. Unpacking and Inspection

Carefully remove the pump from its packaging. Inspect all components for any signs of damage. Ensure all parts are present:

  • Hobbywing Combo Pump 5L Brushless Water Pump V1
  • Integrated wiring harness
Hobbywing 5L Brushless Water Pump, front view with wiring

Figure 2: Front view of the pump with its integrated wiring.

2. Mounting the Pump

The pump features a robust mounting bracket. Securely attach the pump to a stable surface on your UAV or agricultural equipment using appropriate fasteners (not included). Refer to the dimensions for proper fitment and hole alignment.

Dimensional drawing of the Hobbywing 5L Brushless Water Pump

Figure 3: Dimensional drawing showing pump size and mounting points.

3. Wiring Connections

The pump comes with an integrated wiring harness for power and signal. Ensure all connections are secure and correctly polarized to prevent damage.

  1. Power Connection: Connect the main power wires (typically red for positive, black for negative) to your 12-14S (DC44-60.9V) power source. The pump includes a waterproof connector for this purpose.
  2. Signal Connection: Connect the signal wire (typically brown/white/red or similar) to your flight controller or PWM signal generator. The pump supports a fixed PWM throttle stroke of 110-1940US.
Close-up of the waterproof power connector on the pump's cable

Figure 4: Detail of the waterproof power connector.

Close-up of the signal and power wires for connection

Figure 5: Detail of the signal and bare-end power wires for connection to the system.

4. Fluid Connections

Connect your water inlet hose to the 10.5mm inlet port and your outlet hose (leading to nozzles) to the 6.5mm outlet port. Ensure all hose clamps are tight to prevent leaks.

Operating Instructions

1. Powering On

Once all connections are secure and fluid lines are attached, apply power to your system. The pump will be in standby mode until a PWM signal is received.

2. Flow Control

Control the pump's flow rate using the PWM signal from your flight controller or remote control system. Adjust the PWM signal within the specified range (110-1940US) to achieve the desired flow rate for your spraying application.

3. Shutting Down

To stop the pump, reduce the PWM signal to its minimum value or cut power to the pump. Always ensure the pump is off before disconnecting power or fluid lines.

Maintenance

1. Cleaning

After each use, especially when spraying agricultural chemicals, flush the pump with clean water to prevent residue buildup and corrosion. This helps maintain optimal performance and extends the pump's lifespan.

2. Inspection

Regularly inspect the pump, hoses, and connections for any signs of wear, damage, or leaks. Pay close attention to the inlet and outlet ports and the electrical wiring. Replace any worn or damaged components immediately.

3. Storage

When not in use, store the pump in a clean, dry environment, away from direct sunlight and extreme temperatures. Ensure all fluid has been drained from the pump before storage, especially in freezing conditions.

Troubleshooting

1. Pump Not Starting

  • Check power connections: Ensure the pump is receiving the correct voltage (12-14S, DC44-60.9V) and polarity is correct.
  • Verify PWM signal: Confirm that the flight controller or signal generator is sending a valid PWM signal within the 110-1940US range.
  • Inspect wiring: Look for any loose or damaged wires in the harness.

2. Low Flow Rate or No Output

  • Check fluid supply: Ensure the water tank has sufficient fluid and the inlet hose is not kinked or blocked.
  • Inspect for air in the system: Prime the pump if necessary by ensuring the inlet is submerged and running the pump briefly to expel air.
  • Clean filters: If an inline filter is used, check if it is clogged.
  • Verify PWM signal: Ensure the PWM signal is set to a value that should produce adequate flow.

3. Leaks

  • Inspect hose connections: Tighten all hose clamps at the inlet and outlet ports.
  • Check for cracks: Examine the pump housing and hoses for any visible cracks or damage.

User Tips

  • Always use clean, filtered water to prevent clogging and damage to the pump's internal components.
  • Ensure the pump is securely mounted to minimize vibration during operation, which can prolong its lifespan.
  • For optimal performance in UAV applications, integrate the pump's PWM control with your flight controller for precise flow management based on flight parameters.
  • Consider using quick-disconnect fittings for easier setup and breakdown, especially for frequent tank refills or cleaning.

Warranty and Support

For any technical assistance, warranty claims, or support inquiries, please contact the seller or manufacturer directly. Keep your purchase records handy for faster service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.