PowMr BE24

Contents

PowMr 24V Solar System Battery Equalizer Instruction Manual

Model: BE24

1. Introduction

The PowMr Battery Equalizer (Model BE24) is an essential device for maintaining the health and longevity of your battery bank in solar systems. It is specifically designed for 12V Gel, Flood, and AGM Lead Acid batteries connected in series. This equalizer actively monitors and balances the voltage of individual batteries within a series-connected bank (e.g., 24V, 36V, 48V systems). By shunting current from higher-voltage batteries to lower-voltage ones, it prevents voltage discrepancies that can lead to reduced performance and premature battery failure. This ensures optimal charging and discharging cycles, extending the overall lifespan of your battery system.

PowMr BE24 Battery Equalizer front view

Figure 1: PowMr BE24 Battery Equalizer

Video 1: PowMr Battery Equalizer Product Overview

2. Specifications

FeatureSpecification
Model NumberBE24
ApplicationCharger Controller, Battery System
Working Voltage2x12V (for 24V, 36V, 48V systems)
Working Current0~5A
Standby CurrentLess than 3mA
Maximum Current5A
Temperature Sensor-20°C to +55°C
ProtectionReverse polarity protection
Low Voltage Disconnect10V
Dimensions (L*W*H)70*70*27 mm
CertificationCE
Compatible Battery TypesGel, Flood, AGM Lead Acid Batteries

3. Setup and Installation

The Battery Equalizer is designed for easy installation. Please follow these steps carefully to ensure correct and safe operation.

3.1 System Compatibility

  • For a 24V battery system (two 12V batteries in series), use 1 piece of the equalizer.
  • For a 36V battery system (three 12V batteries in series), use 2 pieces of the equalizer.
  • For a 48V battery system (four 12V batteries in series), use 3 pieces of the equalizer.
  • The equalizer can be used for any N*12V battery system by connecting N-1 equalizers.

3.2 Wiring Instructions

Ensure all power sources are disconnected before making any connections. Connect the equalizer to your battery bank as follows:

  1. Black Wire: Connect the black wire to the negative (-) pole of the entire series battery pack.
  2. Red Wire: Connect the red wire to the positive (+) pole of the entire series battery pack.
  3. White Wire: Connect the white wire to the intermediate connection point between the two 12V batteries that are in series. For systems with more than two batteries, each equalizer will connect across two adjacent 12V batteries.
Wiring diagram for 24V, 36V, and 48V battery systems using the PowMr Battery Equalizer

Figure 2: Connection Diagram for various battery bank configurations

Important: The equalizer features reverse polarity protection. However, always double-check your connections before applying power to prevent damage to the unit or your battery system.

4. Operating Instructions

Once correctly installed, the PowMr Battery Equalizer operates automatically. It continuously monitors the voltage of the series-connected batteries.

4.1 Automatic Balancing

The equalizer activates when it detects a voltage difference of approximately 20mV or more between two adjacent 12V batteries in the series. It then shunts current from the battery with the higher voltage to the battery with the lower voltage until their voltages are nearly equal. This process occurs during charging, discharging, and idle states, ensuring consistent battery health.

4.2 LED Indication

The equalizer provides visual feedback through its LED indicators (A and B) to show the balancing status. The specific behavior of the LEDs depends on the voltage levels of the connected batteries.

LED indication diagram for battery voltage states

Figure 3: LED Indicator States

  • When Battery A or Battery B is lower than 10V:
    • If Battery A is lower than 10V: LED A is ON, LED B is OFF.
    • If Battery B is lower than 10V: LED B is ON, LED A is OFF.
    • If both Battery A and Battery B are lower than 10V: LED A and LED B are both ON.
  • When Battery A or Battery B is higher than 10V:
    • If Battery A voltage is higher than Battery B: LED A is ON, LED B is OFF.
    • If Battery B voltage is higher than Battery A: LED B is ON, LED A is OFF.
    • If Battery A and Battery B are at the same voltage: LED A and LED B are both OFF.

The equalizer will automatically disconnect if the battery voltage drops below 10V (Low Voltage Disconnect) to protect the batteries from over-discharge.

5. Maintenance

The PowMr Battery Equalizer is designed for minimal maintenance. However, regular checks can help ensure its optimal performance and the longevity of your battery system.

  • Visual Inspection: Periodically inspect the equalizer and its connections for any signs of damage, corrosion, or loose wiring.
  • Cleanliness: Keep the unit clean and free from dust and debris. Use a dry, soft cloth for cleaning.
  • Environmental Conditions: Ensure the equalizer is installed in a location that adheres to its specified operating temperature range (-20°C to +55°C) and is protected from direct moisture.
  • Battery Health Check: Regularly monitor your battery voltages to confirm the equalizer is functioning correctly and maintaining balance.

6. Troubleshooting

If you encounter issues with your battery equalizer, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No LEDs are lit
  • Incorrect wiring.
  • Battery voltage below 10V (Low Voltage Disconnect).
  • Batteries are already balanced (voltage difference less than 20mV).
  • Check all wiring connections according to the diagram.
  • Verify battery voltage. If below 10V, charge the battery.
  • This may be normal operation if batteries are balanced.
Only one LED (A or B) is lit continuously
  • Significant voltage difference between Battery A and Battery B.
  • One battery is significantly lower than 10V while the other is not.
  • The equalizer is actively balancing. Allow time for balancing.
  • Check individual battery health. A faulty battery may not balance.
Both LEDs (A and B) are lit continuously
  • Both batteries are below 10V.
  • Charge the battery bank immediately.
  • Check the overall charging system.
Equalizer appears damaged or not working
  • Physical damage.
  • Internal fault.
  • Inspect the unit for visible damage.
  • Contact customer support if the unit is faulty.

7. User Tips

  • Initial Inspection: Upon receiving the product, carefully inspect the unit and its packaging for any signs of damage during transit.
  • Parallel Strings: If you have multiple parallel strings of series-connected batteries (e.g., a 2S3P AGM pack), you can use multiple equalizers in parallel, one for each series string, to ensure comprehensive balancing across your entire battery bank.
  • Battery Type Compatibility: This equalizer is compatible with Gel, Flood, and AGM Lead Acid batteries. Ensure your battery type matches these specifications for optimal performance.
  • System Voltage Verification: Always confirm your battery system voltage (24V, 36V, 48V, etc.) and install the appropriate number of equalizers as specified in the "System Compatibility" section.

8. Warranty and Support

This product comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please contact your retailer or the manufacturer directly. Refer to the product packaging or the seller's website for contact information.

California Proposition 65 Warning: ⚠️Warning: This product contains lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. For more information go to www.P65Warnings.ca.gov/.

© 2023 PowMr. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.