ZEEWEII DSO1511G

Contents

ZEEWEII DSO1511G/DSO1511E Digital Oscilloscope User Manual

Model: DSO1511G / DSO1511E

Brand: ZEEWEII

1. Introduction

The ZEEWEII DSO1511G/DSO1511E is a high-performance, portable digital oscilloscope designed for accurate waveform analysis and signal generation. The DSO1511G is an upgraded version of the DSO1511E, featuring a USB Type-C port, an integrated signal generator, and video output capabilities. Its ARM+FPGA+ADC architecture ensures stable operation and high precision, making it an essential tool for various electronic testing and debugging tasks.

ZEEWEII DSO1511G Digital Oscilloscope showing a sine wave on its screen, highlighting 120MHz bandwidth, 500MS/s sampling rate, video output, 10mV/div sensitivity, and signal generator function.
Figure 1: ZEEWEII DSO1511G Digital Oscilloscope

2. Setup

2.1 Package Contents

Before using your oscilloscope, please verify that all items are present in the package:

Contents of the ZEEWEII DSO1511G package, including the oscilloscope unit, a P6100 probe, a Type-C USB cable, a video cable, a Gen Pin, a storage bag, and a user's manual.
Figure 2: Package Contents
  • ZEEWEII DSO1511G/DSO1511E Digital Oscilloscope Unit
  • P6100 Probe
  • Type-C USB Cable
  • Video Cable
  • Gen Pin
  • Storage Bag
  • User's Manual (this document)

2.2 Charging the Device

The oscilloscope has a built-in 3.7V, 2500mAh rechargeable lithium battery. Before first use, fully charge the device using the provided Type-C USB cable and a compatible USB power adapter (not included). The charging indicator will typically show the charging status.

2.3 Initial Power-On

Press and hold the 'Power' button (labeled 'xKey Power' on the device) to turn on the oscilloscope. The device will boot up and display the main waveform interface.

3. Operating Instructions

3.1 Basic Operation and Interface

The oscilloscope features a 2.4-inch color TFT LCD display and a set of navigation buttons for control. The main interface displays the waveform, measurement parameters, and status indicators.

Close-up of the ZEEWEII DSO1511G oscilloscope screen and control buttons, showing a sine wave and various measurement parameters.
Figure 3: Oscilloscope Interface and Controls
  • OK/Auto Button: Initiates auto-measurement or confirms selections.
  • Run/Stop Button: Pauses or resumes waveform acquisition.
  • xKey Power Button: Power on/off.
  • Menu Button: Accesses the main menu for settings and functions.
  • Navigation Buttons (Up, Down, Left, Right): Used for menu navigation and adjusting parameters.
  • mV/V Button: Adjusts vertical sensitivity (Volts per Division).
  • s/ns Button: Adjusts horizontal time base (Seconds per Division).

3.2 Measuring Signals

Connect the P6100 probe to the BNC connector on the top of the oscilloscope. Attach the probe clip to the circuit point you wish to measure. Use the 'mV/V' and 's/ns' buttons to adjust the vertical and horizontal scales to properly view the waveform.

Video 1: Product Demonstration (Signal Measurement, Generation, and Export)

3.3 Signal Generator Function

The DSO1511G includes a built-in squarewave generator. This function can output a 3V amplitude squarewave with an adjustable frequency range of 0-2MHz (accuracy up to 0.1Hz) and a duty cycle range of 1%-99%. It can be used for probe calibration, driving MOSFETs, or replacing crystals.

ZEEWEII DSO1511G oscilloscope displaying a square wave, with text indicating Signal Generator Frequency: 0-2MHz and Waveforms: sin, square, triangle, noise.
Figure 4: Signal Generator Interface

To access the signal generator, navigate through the menu. You can select various waveforms including sine, square, triangle, and noise. The video demonstration (Video 1) also shows the square wave signal output.

3.4 FFT (Fast Fourier Transform)

The FFT function converts time-domain waveforms into the frequency domain, useful for harmonic analysis. The device supports three display modes: logarithmic, linear, and music spectrum. Access this feature via the menu to analyze the frequency components of your signals.

3.5 Reference Waveform

This feature allows you to "lock" a current waveform on the screen as a reference. Subsequent live waveforms will be displayed alongside the reference, enabling easy comparison between two channels or different signal states. This is particularly useful for single-channel oscilloscopes.

3.6 Trigger Modes

The oscilloscope offers comprehensive triggering options to stabilize and capture specific parts of a waveform:

  • Trig Mode: Auto, Normal, Single
  • Trigger Types: Rise (positive edge), Fall (negative edge)
  • Trigger Level: Manual or Auto adjustment

Adjusting the trigger level and type helps in capturing stable waveforms, especially for non-repeating or complex signals.

3.7 Waveform Save and View

You can save screen waveforms with a single click. The device can store up to 250 waveform images. Saved waveforms can be previewed as thumbnails, and clicking a thumbnail allows full-screen observation. Unwanted waveforms can be deleted from storage.

3.8 Exporting Waveforms to Computer

Connect the oscilloscope to a computer using the provided Type-C USB cable. The device will appear as a storage device. You can then export up to 50 user-stored waveforms at a time. These images can be used for documentation, analysis, or sharing.

3.9 Detailed Analysis

After stopping waveform acquisition (using the 'Stop' button), you can move the waveform left and right across the screen. This allows you to zoom in (by adjusting the timebase) and examine specific details of the captured waveform, aiding in problem diagnosis and analysis.

4. Applications

The ZEEWEII DSO1511G/DSO1511E is suitable for a variety of applications, including:

Multiple images showing the ZEEWEII DSO1511G oscilloscope being used in various practical scenarios, such as car repair, circuit debugging, and general electronic testing.
Figure 5: Practical Applications of the Oscilloscope
  • Basic R&D
  • Car Repair
  • Home Appliance Repair
  • Switching Power Supply Debugging
  • Hi-Fi Music Fever (audio circuit analysis)
  • Inverter Testing
  • 220V Mains (with appropriate safety precautions and probe settings)
  • MCU Debugging
  • DIY Electronic Competitions

The device also supports 100:1 probes for high voltage measurements (probe not included, but settings are available).

5. Maintenance

5.1 Cleaning

To clean the device, use a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the casing or screen. Keep the BNC connector and probe tips clean and free of debris.

5.2 Battery Care

To prolong battery life, avoid fully discharging the battery frequently. If storing the device for an extended period, ensure it is charged to approximately 50-70% capacity. Recharge periodically if stored for very long durations.

5.3 Storage

Store the oscilloscope in a cool, dry place, away from direct sunlight and extreme temperatures. Use the provided storage bag to protect it from dust and physical damage.

6. Troubleshooting

  • No Display/Power On: Ensure the battery is charged. Connect the Type-C cable to a power source and try again.
  • No Signal on Screen:
    • Check probe connection to the device and the circuit.
    • Verify the probe is properly connected to the signal source.
    • Adjust vertical (mV/V) and horizontal (s/ns) scales.
    • Check trigger settings (mode, type, level). Try 'Auto' mode first.
  • Unstable Waveform: Adjust the trigger level and trigger type (Rise/Fall) to stabilize the waveform. Use 'Normal' or 'Single' trigger modes for specific events.
  • Incorrect Measurements:
    • Ensure the probe attenuation setting on the oscilloscope matches the physical probe (e.g., 1X or 10X).
    • Calibrate the probe if necessary (using the built-in squarewave generator).
  • Device Not Recognized by Computer: Ensure the Type-C cable is securely connected. Try a different USB port or cable.

7. Specifications

FeatureSpecification
ModelDSO1511G (Upgraded from DSO1511E)
Hardware SolutionARM+FPGA+ADC
Display2.4 inch TFT LCD
Display Resolution320x240 Pixels
Analog Bandwidth120MHz
Digital Channels1
Sampling Rate500MS/s
Rise Time<3ns
Storage Depth128Kbit
Vertical Sensitivity10mV/div - 10V/div
Time Base Range5ns - 10s
Trigger ModeAuto/Normal/Single
Trigger TypeRise/Fall
Trigger LevelManual/Auto
Waveform Measurement14 types
Waveform Storage250 groups
FFT SupportYes (Logarithmic, Linear, Music Spectrum)
Signal Generator WaveformsSine, Square, Triangle, Noise
Signal Generator Frequency0-2MHz
Signal Generator Amplitude3V (Squarewave)
Video OutputYes
BatteryBuilt-in 3.7V, 2500mAh Lithium Battery
Charging InterfaceType-C USB
Dimensions107x70x24mm
Weight150g
DIY Supplies CategoryElectrical
OriginMainland China

8. User Tips

  • Probe Attenuation: The oscilloscope supports 1:100 probe settings in the menu, in addition to standard 1:10. Ensure the setting matches your physical probe for accurate readings.
  • Probe Calibration: The device's probes typically come factory-calibrated. However, if you are using a new probe or suspect inaccuracies, you can use the built-in squarewave generator to calibrate it.
  • FFT Functionality: For frequency analysis, utilize the FFT function. It offers logarithmic, linear, and music spectrum display modes to suit different analysis needs.

9. Warranty and Support

For any technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the ZEEWEII Official Store or your point of purchase. The product typically includes a policy for free returns within 90 days and guarantees fast delivery with refunds for specific issues such as delays, lost packages, or damaged items.

© 2024 ZEEWEII. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.