1. Introduction
Thank you for purchasing this Genuine Mazda Accessory. This manual provides detailed instructions for the installation, operation, and maintenance of your new USB Media Hub Retrofit Kit, enabling Apple CarPlay and Android Auto functionality in your Mazda vehicle. Please read these instructions thoroughly before beginning installation to ensure proper use and to prevent injury or damage.
This kit enhances your MAZDA CONNECT infotainment system, allowing seamless integration with your smartphone. Access maps, playlists, contacts, and compatible apps using voice commands via Siri (for Apple CarPlay) or Google Assistant (for Android Auto). The system supports both wired and, depending on the version, wireless connections.
Important: The firmware MUST BE UPDATED FIRST before beginning the installation. If an older version of the CMU software is being used, the CarPlay/Android Auto-compatible USB hub may not be recognized. The software must be v70.00.21 or later. If not, be sure to update the software. Once the CMU has been attached to the CarPlay/Android Auto-compatible USB hub, the software cannot be updated.
For MCU firmware upgrade files, please refer to the following resource: MCU Firmware Upgrade Guide.
For a visual installation guide, you may refer to this video: Installation Video.
2. Safety Information
WARNING
- Indicates a situation in which serious injury or death could result if the warning is ignored.
- Do not allow the cord connected to the USB port to get tangled in the selector lever/shift lever. If the cord gets tangled, it could be a distraction to your driving and result in an unexpected accident.
- Before performing any work, park the vehicle on level ground, apply the parking brake securely, and then block the wheels.
- When the negative battery is connected during operation, it may cause electric shock or other personal injuries. Disconnect the negative cable before installation.
- When connecting/disconnecting connectors, grasp the connectors, not the wires. Otherwise, a short, and an accident from poor contact or fire may occur.
- Make sure the connector is securely pressed in until a click sound is heard. Otherwise, an accident may occur due to an open circuit or poor contact.
- Secure the harness with the band (part included) so it doesn't dangle. If not, it may cause a short, accident, or fire.
- Do not pull the harness with excessive force. Doing so can cause a breakage or a short-related accident, as well as an electrical short or fire.
CAUTION
- Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored.
- Using improper tools may cause damage and/or broken parts. Use the correct tool for the job.
- Wrap protective tape around screwdrivers and fastener remover tools to prevent scratching the vehicle.
- Excessive length of tie wrap may interfere with other parts and cause damage.
- Put the removed parts and the parts in the kit on the protective sheet to prevent scratches.
- If there is dust, dirt or grease on the adhesion surface, the adhesive strength of the double-sided adhesive tape will splotch and adhesive power of the tape will be reduced. Wash and degrease the surface of the adhesion area before applying the double-sided adhesive tape. Be sure to wash interior and exterior parts using IPA (isopropyl alcohol).
- Do not modify the USB cable set.
- Do not install the USB cable set in any way other than described in the following instructions.
- If you have any questions about the use of the accessory, ask your Mazda dealer for proper advice before using it.
- Mazda and its suppliers are not responsible for injuries, accidents, and damage to persons and property that arise from the failure of the dealer or installer to follow these instructions.
- To ensure safety and reliability of the work, installation, removal and disposal work must carried out by an Authorized Mazda Dealership.
- Be careful not to lose removed parts, and be sure that they are kept free from scratches, grease or other dirt.
3. Package Contents
Verify that the kit includes all the following parts and that the parts are not dirty, scratched, or damaged.

| Part | Part Name | Quantity |
|---|---|---|
![]() | USB cable (Gray/Blue-Brown) | 1 |
![]() | USB cable (Gray/Green-Black) | 1 |
![]() | Tie wrap (L=200mm) | 9 |
![]() | Sponge tape (100×30mm 10 sheets) | 2 |
![]() | Owner's manual Parts list | Each 1 |
![]() | HUB unit (Part No. TK78 66 9U0C) | 1 |
Note: The HUB unit (Part No. TK78 66 9U0C) is sold separately and is necessary for installation.
4. Required Tools
- Phillips screwdriver
- Wrench or Glasses wrench
- Scissors
- Torque wrench
- Fastener remover
- Scale
- Socket wrench
- Tape-wrapped flathead screwdriver
- Nipper
- Soft clean cloth
- IPA (Isopropyl alcohol)
- Mat
- Protective tape
- Protective gloves
5. Firmware Update
Before proceeding with the physical installation, it is crucial to update your Mazda Connect infotainment system's firmware. An outdated firmware version (earlier than v70.00.21) may prevent the CarPlay/Android Auto-compatible USB hub from being recognized or functioning correctly. Once the CMU has been attached to the USB hub, the software cannot be updated.
Procedure:
- Switch the car OFF.
- Remove the Navigation SD Card from its slot and keep it out of the car until the final firmware file is installed.
- Follow the instructions provided in the MCU firmware upgrade guide (e.g., via USB drive) to update your system. A YouTube link for this is provided in the Introduction section.
- Once the firmware update is complete, switch the car OFF again.
- Re-insert the Navigation SD Card.
- Start the car. The navigation should now work as normal with the updated CONNECT system.
6. Installation Instructions
Refer to the vehicle's Workshop manual for detailed removal and installation procedures of existing parts. Parts that have been removed will not be reused, except for the Navigation SD Card.
6.1. USB Hub Installation
- Remove the Navigation SD Card from the SD Card slot (this will be reused).
- Remove the existing AUX unit from the vehicle.
- Install the new HUB unit (sold separately) into the vehicle.
- Install the Navigation SD Card into the new HUB unit.

6.2. Connection Diagram

Note: To prevent noise, wrap the disconnected vehicle wiring harness connector with a piece of sponge tape (100 x 30 mm). The diagram shows the case when there is a single vehicle wiring harness connector. If there are two vehicle wiring harness connectors, carry out the same procedure for both connectors.
6.3. DIP Switch Settings (for P21, P31, P32 versions)
Some versions of the USB hub feature DIP switches to configure wired or wireless CarPlay/Android Auto functionality. Refer to the diagram below for specific settings:

- Wireless CarPlay: Set DIP switches 1+2 down & 3+4 up.
- Wired CarPlay + Wired Android Auto: Set DIP switches 1+2 up & 3+4 down.
7. Operation
7.1. Operation Check
With the vehicle on, select APPLICATIONS from the Mazda Connect Home Screen and verify that the options for Apple CarPlay and Android Auto are shown.
While following the procedure given in the Workshop manual, use the diagnosis assist function of the connectivity master unit or the diagnostic device to check that no service codes are displayed.
7.2. Connecting an iPhone (Apple CarPlay)
Insert an Apple-genuine connector cord into the USB port and connect the iPhone. Insert or pull out the plug with the plug perpendicular to the USB port.

Note:
- When an iPhone connected to Bluetooth® is connected to the vehicle's USB port, the system switches to Apple CarPlay. Applications that you were using when connected to Bluetooth® can continue to be used. However, the functions that can be used with a Bluetooth® connection and the functions which can be used by Apple CarPlay differ depending on the application.
- Before use, carefully read the user instructions for the iPhone.
- Do not use the Mazda Connect for a long time with the engine stopped. Otherwise, the battery power could be depleted.
- Insert the Apple-genuine connector cord into the USB port securely.
7.3. Connecting an Android™ Smartphone (Android Auto)
Insert an Android™ Smartphone-genuine connector cord into the USB port to connect the Android™ Smartphone. Insert or pull out the plug with the plug perpendicular to the USB port.

Note:
- To use Android Auto™, you need to enable Bluetooth®.
- The parking brake must be engaged when connecting the Android Auto™ device for the first time.
- Up to 5 Android™ Smartphones can be registered.
- When setting the Device Connection Status of a connected Android™ Smartphone to "Never Enabled", Android Auto™ will not activate even if your Android™ Smartphone is connected to the vehicle's USB port. When you want to use Android Auto™, change the setting.
- Before you use Android Auto™ with your vehicle, you need to download the Android Auto™ application from the Google Play™ on your Android™ Smartphone.
- Before use, carefully read the user instructions for the Android™ Smartphone.
- Do not use the Mazda Connect for a long time with the engine stopped. Otherwise, the battery power could be depleted.
- Insert the Android™ Smartphone genuine connector cord into the USB port securely.
7.4. Displaying Apple CarPlay / Android Auto Screen
Once connected, select APPLICATIONS from the Mazda Connect Home Screen. The options for Apple CarPlay and Android Auto should be visible. You can also press and hold the Home button on the commander switch to display the respective screen.

Apple CarPlay Home Screen:
- Rotate or slide the commander switch to select an icon.
- Press the commander switch to activate the selected application.
- To activate Siri, select and hold the Siri icon or use the voice recognition button on the steering wheel.
- To return to the Mazda Connect screen, select the Mazda Connect icon.
Android Auto Home Screen:
- Rotate or slide the commander switch to select an item or icon.
- Press the commander switch to activate the selected item or icon.
- The media displayed on the Android Auto™ home screen may differ depending on the use conditions and version of the connected Android™ Smartphone.
- To return to the Mazda Connect screen, select the Mazda Connect icon from the menu.
7.5. Video Demonstration
8. Specifications
| Attribute | Value |
|---|---|
| Origin | Mainland China |
| Is touch screen | YES |
| Built-in Screen | NO |
| Function 1 | Wired/Wireless Carplay |
| Function 2 | Wired Android Auto |
| Function 3 | TYPE-C PD fast charging |
| Function 4 | Map Card |
| Function 5 | 3.5mm Aux input |
| Function 6 | Supports original car system |
| Warranty | Lifetime warranty |
Compatible Mazda Models:

This kit is compatible with Mazda models that have MAZDA CONNECT™. If your Mazda does not have a Mazda Connect unit, this kit will not work.
Supported Models and Years:
- MX-5: 2016 to 2020 (including Miata Club, Grand Touring, RF variants)
- CX-3: 2016 to 2019 (including Grand Touring, Sport, Touring)
- CX-5: 2015 to 2020 (including Grand Select, Grand Touring, Signature, Sport, Touring)
- CX-9: 2016 to 2020 (including Grand Touring, Signature, Sport, Touring)
- Mazda 2: 2016 to 2019
- Mazda 3: 2014 to 2018 (including 4-Door and 5-Door i Sport, i Touring, i Grand Touring, s Touring, s Grand Touring)
- Mazda 6: 2016 to 2020 (including Sport, Touring, Grand Touring, Grand Touring Reserve, Signature)
9. Troubleshooting
- Intermittent Connection / Black Screen: If the unit connects intermittently or displays a black screen, try rebooting the head unit or engaging/disengaging reverse gear to activate the screen. Ensure all cables are securely connected.
- Fast Charging Cable Not Working: If the fast charging cable does not work, try using a regular data cable. Ensure the cable is in good condition and properly seated.
- Android Auto Not Working: Ensure your Android™ Smartphone has the Android Auto™ application downloaded from Google Play™ and that Bluetooth® is enabled. The parking brake must be engaged when connecting for the first time. If issues persist, verify the firmware version and DIP switch settings (if applicable for your unit version).
- SD Card Port Not Working: Ensure the Navigation SD Card is inserted correctly and that the firmware update was completed successfully. If the port remains unresponsive, check for any physical obstructions or damage.
- No Recognition After Installation: Double-check that the firmware update to v70.00.21 or later was performed BEFORE installing the new USB hub. If the firmware was not updated prior to installation, the hub may not be recognized.
- Wireless CarPlay/Android Auto Issues: Ensure your iPhone's Bluetooth and Wi-Fi are both enabled. Turn off the original car's Bluetooth function while your iPhone connects to the box. Verify DIP switch settings for wireless mode.
10. User Tips
- Installation: Some users have found success by 3D printing a template to release the 4 clips of the USB hub, making the installation process smoother.
- Initial Connection: The first connection via cable might take a moment to establish. Be patient as the system initializes.
- Software Update: Always perform the MCU firmware update as the very first step. Remove the navigation SD card before the update and re-insert it only after the update is complete and the car has been turned off and on again.
- Performance: While the unit runs Android 11 with 2GB RAM and 16GB storage, it generally performs well without significant lagging, though it might feel slightly underpowered for very demanding tasks.
11. Maintenance
- Regularly check all cable connections to ensure they are secure and free from damage.
- Keep the USB ports and surrounding areas clean and free of dust or debris. Use a soft, dry cloth for cleaning.
- Avoid exposing the unit to extreme temperatures or direct sunlight for prolonged periods, especially when the vehicle is parked, to prevent potential damage.
- Do not use harsh chemicals or abrasive cleaners on the unit or car display.
12. Warranty and Support
This product comes with a lifetime warranty.
For any questions regarding the use of this accessory or for proper advice, please contact your Mazda dealer or the seller.
Keep these instructions after installation. They may be necessary for installing other optional parts, removal of this accessory, or for future reference. Should the vehicle or this accessory be resold, always leave these instructions with it for the next owner.



