MicroZone E6R-E

Contents

MicroZone E6R-E 2.4G Mini 6-Channel Stabilizer Receiver Instruction Manual

For MC6C 6CH Controller Transmitter for RC Airplanes, Drones, and Quadcopters

1. Introduction

The MicroZone E6R-E is a compact and lightweight 2.4GHz 6-channel stabilizer receiver designed for use with the MicroZone MC6C remote control transmitter. It features integrated self-stabilization on channels 1-3 and a switchable self-stabilization function on channel 5, making it ideal for various RC aircraft including airplanes, drones, and quadcopters. This manual provides essential information for proper setup, operation, and maintenance of your E6R-E receiver.

2. Product Overview

Familiarize yourself with the components and ports of your MicroZone E6R-E receiver.

Front view of the MicroZone E6R-E 2.4G Mini Receiver
Figure 1: Front view of the MicroZone E6R-E 2.4G Mini Receiver, showing the Microzone logo, E6R-E model, 2.4GHz S-FHSS label, and channel ports 1-7.
Close-up of the MicroZone E6R-E receiver's port layout
Figure 2: Close-up view of the receiver's port layout, indicating channels 1 through 7, and the LED and SW (switch) indicators.

3. Setup Instructions

3.1 Binding the Receiver to the Transmitter (MC6C)

The E6R-E receiver uses an 'electric shock frequency' mode, which refers to a specific binding procedure to link it with your MC6C transmitter. Follow these steps carefully:

  1. Ensure your MC6C transmitter is turned OFF.
  2. Connect a binding plug (often included with the receiver, see Figure 3) to the 'BIND' or 'B/VCC' port on the E6R-E receiver.
  3. Connect power to the receiver (e.g., from an ESC or a separate battery) through any other channel port (e.g., CH3 or CH4). The LED on the receiver should start flashing rapidly, indicating it is in binding mode.
  4. While holding down the 'BIND' button on your MC6C transmitter, turn the transmitter ON.
  5. Observe the LED on the receiver. It should stop flashing and remain solid, indicating a successful bind.
  6. Release the 'BIND' button on the transmitter, then turn OFF both the transmitter and the receiver.
  7. Remove the binding plug from the receiver.
  8. Turn on the transmitter first, then power on the receiver. The receiver LED should be solid, confirming the link.
MicroZone E6R-E receiver with binding plug inserted
Figure 3: MicroZone E6R-E receiver shown with a binding plug, typically used for the binding process.

3.2 Connecting to Your RC Model

Connect your servos, ESC, and other components to the appropriate channels on the receiver. The E6R-E provides 5 PWM signal channels:

  • CH1-CH3: These channels feature integrated self-stabilization. Connect your aileron, elevator, and rudder servos here for automatic flight assistance.
  • CH5: This channel acts as a self-stabilization switch. Connect a switch channel from your transmitter to CH5 to enable or disable the self-stabilization function during flight.
  • Other Channels (e.g., CH4, CH6, CH7): Use these for throttle, flaps, landing gear, or other auxiliary functions as needed.

4. Operating Instructions

4.1 Powering On and Pre-Flight Checks

  1. Always turn on your MC6C transmitter first.
  2. Then, power on your RC model (which powers the receiver). The receiver's LED should illuminate solid, indicating a stable connection.
  3. Perform a range check and verify all control surfaces (ailerons, elevator, rudder) and other functions respond correctly to transmitter inputs.
  4. Test the self-stabilization switch (CH5) to ensure it toggles the stabilization mode as expected.

4.2 Self-Stabilization Function

The E6R-E receiver's integrated self-stabilization on CH1-CH3 helps maintain stable flight, especially useful for beginners or in windy conditions. The CH5 switch allows you to activate or deactivate this feature during flight, giving you full control over your aircraft's behavior.

5. Maintenance

To ensure the longevity and reliable performance of your MicroZone E6R-E receiver, follow these maintenance guidelines:

  • Keep Dry: Protect the receiver from moisture and humidity. Water damage can lead to malfunctions.
  • Avoid Physical Damage: Mount the receiver securely within your model to prevent vibrations and impacts.
  • Cleanliness: Keep the receiver free from dust, dirt, and debris. Use a soft, dry brush or compressed air for cleaning.
  • Antenna Placement: Ensure the antenna is positioned correctly and not damaged. A damaged or improperly routed antenna can significantly reduce range and signal quality.
  • Voltage Check: Regularly check your power source (battery) to ensure it provides the correct voltage within the receiver's specified range (DC3.5V-7.4V).

6. Troubleshooting

If you encounter issues with your E6R-E receiver, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Receiver LED not solid after powering on.Not bound to transmitter, or transmitter is off.Ensure transmitter is ON. Re-perform the binding procedure (Section 3.1).
No control response from model.Receiver not powered, incorrect wiring, or binding issue.Check power connections. Verify servo/ESC connections to correct channels. Re-bind receiver.
Unstable or erratic control.Interference, low receiver voltage, or damaged antenna.Check for sources of interference. Ensure battery voltage is adequate. Inspect antenna for damage and proper placement.
Self-stabilization not working or always on/off.CH5 switch not configured or faulty.Verify CH5 is connected to a switch channel on your transmitter and configured correctly. Check transmitter settings.

7. Specifications

FeatureSpecification
ModelE6R-E
Dimensions (L x W x H)37mm x 23mm x 13mm
Weight9g
Antenna Length110mm
Output Channels5 PWM (CH1-CH3 with self-stabilization, CH5 self-stabilization switch)
Receiving Frequency2.401MHz - 2.479MHz (S-FHSS)
Voltage RangeDC 3.5V - 7.4V
Frequency ModeElectric Shock Frequency (Binding Procedure)
Compatible TransmitterMicroZone MC6C
MaterialComposite Material
Recommended Age12+ years

8. User Tips

  • Antenna Orientation: For optimal signal reception, try to position the receiver antenna away from large metal objects and at a 90-degree angle to any other antennas in your model.
  • Secure Mounting: Use double-sided foam tape or Velcro to securely mount the receiver in your model, reducing vibration and protecting it from impacts.
  • Power Source: Always ensure your power source (e.g., ESC's BEC or a dedicated receiver battery) can provide stable voltage and sufficient current for all connected servos and the receiver.
  • Test Stabilization: Before flying, always test the self-stabilization function on the ground to understand its behavior and ensure it's configured to your preference.

9. Warranty & Support

For warranty information, technical support, or service inquiries regarding your MicroZone E6R-E receiver, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.