1. Introduction
Thank you for choosing the QIACHIP 4-Channel Wireless Remote Control Switch Receiver. This device is designed for versatile applications, offering convenient wireless control for various electrical systems. Please read this manual carefully before installation and operation to ensure proper use and safety.
This manual provides detailed instructions on the product's features, specifications, installation, operation, and troubleshooting.
2. Safety Information
- Power Off Before Wiring: Always ensure the power supply is disconnected before performing any wiring to prevent electric shock.
- Correct Voltage: Verify that the power supply voltage matches the receiver's specifications (DC 5V-80V).
- Remote Control Compatibility: This receiver is designed to work optimally with QIACHIP brand remote controls (transmitters). Compatibility with other brands is not guaranteed.
- Avoid Interference: When using wireless electronic products, avoid metal surfaces, large electronic devices, and strong electromagnetic fields that can interfere with the signal and reduce remote control range.
- Proper Use: Do not use this electronic product in abnormal ways. Improper use can degrade product performance, shorten lifespan, and potentially cause safety hazards.
3. Product Overview
The QIACHIP KR1204B is a 4-channel wireless remote control switch receiver. It features high sensitivity and an intelligent learning mechanism for secure and flexible control.
3.1 Components

- Antenna: For receiving RF signals from the remote control.
- Indicator: LED light to show status and learning process.
- Learning Button: Used for pairing remote controls and setting working modes.
- Relay: Four independent relays for switching electrical loads.
- Terminals (NO, COM, NC): Normally Open, Common, and Normally Closed contacts for connecting loads.
- Power Supply Terminals (+V, GND): For connecting the DC 5V-80V power input.
3.2 Applications
This versatile remote control switch can be used in a wide range of applications, including:

- Lighting control (lamps, LED lights)
- Garage doors and shutter doors
- Remote control curtains and automated draperies
- DC motor control (forward/reverse)
- Access control systems
- Water pumps and other installations
- Car sunroofs control
- Fans and other universal switch applications
4. Setup and Wiring
Before wiring, ensure all power is disconnected. The receiver supports a DC input voltage range of 5V-80V. The output terminals (NO, COM, NC) can handle loads up to 1V-250V.
4.1 Wiring Instructions for Receiver Module
- +V: Connect to the positive terminal of your DC 5V-80V power supply.
- GND: Connect to the negative terminal of your DC 5V-80V power supply.
- NO (Normally Open): This terminal is open when the relay is off and closes when the relay is activated.
- COM (Common): This is the common terminal for the relay.
- NC (Normally Closed): This terminal is closed when the relay is off and opens when the relay is activated.
4.2 Wiring Diagrams
Below are common wiring diagrams for connecting lamps and DC motors. Always ensure correct polarity and voltage for your specific application.

Note: Do not install or wire with electricity connected. Ensure power is off during installation.
5. Operating Modes
The QIACHIP receiver supports three primary working modes, plus several combined modes, which determine how the relays respond to remote control button presses.
5.1 Momentary Mode (Jog)
In this mode, the relay is activated only while the remote control button is pressed and held. Releasing the button deactivates the relay.
- Action: Press and hold a remote control button (e.g., 'A').
- Result: The corresponding relay turns ON.
- Action: Release the remote control button.
- Result: The corresponding relay turns OFF.
5.2 Toggle Mode (Self-Lock)
In this mode, each press of a remote control button toggles the state of the corresponding relay (ON/OFF).
- Action: Press a remote control button (e.g., 'A') once.
- Result: The corresponding relay turns ON.
- Action: Press the same remote control button ('A') again.
- Result: The corresponding relay turns OFF.
5.3 Latching Mode (Inter-Lock)
In this mode, pressing one button turns on its corresponding relay and simultaneously turns off any other active relay. This is useful for applications where only one output should be active at a time, such as motor direction control.
- Action: Press remote control button 'A'.
- Result: Relay A turns ON. Any other active relay turns OFF.
- Action: Press remote control button 'B'.
- Result: Relay B turns ON. Relay A turns OFF.
5.4 Combined Modes
The receiver also supports advanced combined modes for more complex control scenarios:
- 2CH Momentary + 2CH Toggle: Two channels operate in Momentary mode, and two channels operate in Toggle mode.
- 2CH Momentary + 2CH Latched: Two channels operate in Momentary mode, and two channels operate in Latching mode.
- 2CH Toggle + 2CH Latched: Two channels operate in Toggle mode, and two channels operate in Latching mode.
- 2CH Latching + 2CH Latched: All four channels operate in Latching mode, typically in two pairs.
6. Pairing Remote Controls and Setting Modes
The working mode can only be set when the LED indicator on the switch controller is lit.

6.1 Set Momentary Mode (Jog)
- Press the receiver's learning button once. The LED on the receiver will light up, indicating it's in setting mode.
- Press any button on the remote control (e.g., button 'A') once. The receiver's LED indicator will flash three times and then turn off. Momentary mode is successfully set.
6.2 Set Toggle Mode (Self-Lock)
- Press the receiver's learning button twice. The LED on the receiver will light up, indicating it's in setting mode.
- Press any button on the remote control (e.g., button 'A') once. The receiver's LED indicator will flash three times and then turn off. Toggle mode is successfully set.
6.3 Set Latching Mode (Inter-Lock)
- Press the receiver's learning button three times. The LED on the receiver will light up, indicating it's in setting mode.
- Press the first button on the remote control (e.g., button 'A') once. Then, press the second button on the remote control (e.g., button 'B') once. The receiver's LED indicator will flash three times and then turn off. Latching mode is successfully set (button 'A' for ON, button 'B' for OFF).
6.4 Set Combined Modes
To set combined modes, follow these steps:
- 2CH Momentary + 2CH Toggle: Press the learning button four times. Then press any remote button once.
- 2CH Momentary + 2CH Latched: Press the learning button five times. Then press any remote button once.
- 2CH Toggle + 2CH Latched: Press the learning button six times. Then press any remote button once.
- 2CH Latching + 2CH Latched: Press the learning button seven times. Then press any remote button once.
7. Reset Function (Deleting Paired Remotes)
This function clears all previously paired remote controls from the receiver's memory. After a reset, no remote control will be able to operate the receiver until re-paired.
- Press the receiver's learning button eight times.
- The receiver's LED indicator will flash eight times and then turn off. This indicates that all remote control data has been successfully deleted.
8. User Tips
- Versatile Control: This universal remote control switch offers convenient control over various devices, improving security with access control systems and providing flexibility with multiple working modes.
- Wide Voltage Range: The receiver is suitable for DC 5V-80V, making it compatible with common DC12V and DC24V systems, offering flexible usage.
- Motor Control: Many users find this kit ideal for controlling DC motors, including those for garage doors, curtains, and other automated systems, allowing for forward and reverse operation.
- Signal Range: While the device has high sensitivity, environmental factors like walls and other electronic devices can affect the signal range. Consider the placement of the receiver and remote for optimal performance.
- Battery Check: If you experience reduced remote control range or unresponsiveness, check and replace the remote control battery if necessary.
9. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote control not working | Low/dead remote battery; Remote not paired; Incorrect working mode set. | Replace remote battery; Re-pair the remote control; Re-set the working mode. |
| Short operating range | Obstacles (metal, walls); Electromagnetic interference; Low remote battery. | Relocate receiver/remote; Reduce interference sources; Replace remote battery. |
| Receiver does not respond | No power to receiver; Incorrect wiring; Receiver reset. | Check power supply connection; Verify wiring according to diagrams; Re-pair remote controls. |
| Relay not switching correctly | Incorrect working mode set; Faulty relay. | Re-set the desired working mode; Contact support if relay is faulty. |
10. Maintenance
- Keep the receiver and remote controls in a dry environment, away from moisture and extreme temperatures.
- Clean the devices with a soft, dry cloth. Do not use harsh chemicals or solvents.
- Regularly check the remote control battery and replace it when necessary to ensure optimal performance.
- Ensure all wiring connections are secure and free from corrosion.
11. Specifications
| Parameter | Value |
|---|---|
| Model Number | KR1204B-4 |
| Working Voltage | DC 5V-80V |
| RF Frequency | 433.92MHz |
| Quiescent Current | 5mA |
| Load Power | 120W × 4 |
| Matching Method | Learning Button |
| Receiving Sensitivity | > -104dBm |
| Operation Modes | Momentary, Toggle, Latching, Combined Modes |
| Output Terminals | NO (Normally Open), NC (Normally Closed), COM (Common) |
| Supported Encoding Chip | Learning Code (EV1527) |
| Modulation Mode | ASK |
| Max Paired Remotes | Up to 20 pcs |
| Working Temperature | -10°C to +80°C |
| Dimensions (L×W×H) | 73mm × 55mm × 30mm |
12. Warranty and Support
For warranty information and technical support, please refer to the official QIACHIP website or contact your retailer. You can find more services and information at www.qiachip.com.
A user manual in PDF format is available for download on the product page for detailed diagrams and instructions.