HLTNC 2.2kW ER20 Square Air Cooled Spindle Motor and VFD Kit

Contents

HLTNC 2.2kW ER20 Square Air Cooled Spindle Motor and VFD Kit Instruction Manual

For CNC Milling Machines

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your HLTNC 2.2kW ER20 Square Air Cooled Spindle Motor and Variable Frequency Drive (VFD) Kit. Please read this manual thoroughly before using the product to ensure safe and efficient operation.

The kit typically includes:

  • 2.2kW Spindle Motor
  • 2.2kW Inverter (HY or YL620/YL620-A model)
  • ER20 Collet Set (1-13mm)

For a comprehensive PDF version of the user manual, please refer to the User Manual (PDF).

2. Safety Precautions

WARNING: High voltage inside. Maintenance should only be performed by well-trained personnel.

2.1 General Safety Guidelines

  • Always ensure the power supply is disconnected before performing any installation, wiring, or maintenance.
  • Verify that the ordered specifications match the nameplate (Working voltage and KVA number).
  • Check for any damage or deformation to the unit during transportation.
  • Ensure all internal assembly parts, wiring, and circuit boards are free from abnormalities.
  • Confirm all terminals are locked tightly and there is no foreign matter in the machine.
  • Verify that all buttons on the operator panel function normally.
  • Ensure all additional accessories are present.

2.2 Installation Location and Environment

  • Temperature: Operate within an ambient temperature range of -5°C to 40°C.
  • Humidity: Avoid places with dripping water and high humidity.
  • Exposure: Do not install in direct sunlight, high temperature, or severe dust environments.
  • Corrosion: Keep away from corrosive gases and liquids.
  • Cleanliness: Ensure the area is free from excessive dust, oil, and metal particles.
  • Vibration: Install in a location free from vibration to facilitate easy maintenance and inspection.
  • Noise: Avoid areas with electromagnetic noise interference.
  • Ventilation: Install the inverter vertically to ensure good air circulation and sufficient space around it for cooling and maintenance.
  • Mounting: If the installation surface is not secure, place a flat plate under the inverter's base. Loose mounting can stress and damage main circuit parts. The installation wall should be made of non-combustible materials like iron plates.
  • Multiple Inverters: When installing multiple inverters in the same cabinet, ensure proper spacing and add a baffle plate in the middle.

2.3 Braking Resistor Safety

  • The installation of a braking resistor must consider environmental safety and flammability. Maintain a distance of at least 100mm from the inverter.
  • If you need to change the resistance and power of the braking resistor, contact your local dealer.
  • Braking resistors must be ordered separately if needed.
  • For machinery with large inertia, increase the capacity of the braking resistor. Contact your local dealer for details.

3. Specifications

3.1 Spindle Motor Specifications

AttributeValue
Brand NameHLTNC
Model Number2.2KW Air Cooled Spindle
DriveMotor
Maximum Torque1.17Nm
Operating Speed24000rpm
ApplicationMilling
Voltage Options110V/220V/380V
Collet TypeER20
Spindle Frequency300Hz/400Hz
CertificationCE
OriginMainland China
Runout offless than 0.005mm
LubricationGrease Lubrication

3.2 VFD (Variable Frequency Drive) Specifications

AttributeValue
Type2.2kW/220V/380V (YL620-A or HY)
Input VoltageAC 220V (+/-15%)
Input Frequency50/60Hz (48-63Hz)
Input Phase1 or 3 phase
Output VoltageAC 220V
Output Current10A
Output Frequency0-400Hz
Output Phase3 phase
Control MethodV/F control; Open-loop flux vector control
Warranty1 year from the date purchased

3.3 Product Dimensions and Weight

ComponentDimensions (L x W x H)Weight
Spindle Motor (approx.)272mm x 80mm x 110mm~1.5KG
VFD (approx.)160mm x 122mm x 170mm~1.5KG
Package40cm x 33cm x 20cm7.8KG

The factory default setting of YL inverter is 400Hz, no need to set it, it is suitable for our spindle motor.

Product parameter diagram with dimensions for the spindle motor.
Figure 1: Spindle Motor Dimensions
YL Inverter with dimensions.
Figure 2: YL Inverter Dimensions

4. Setup and Installation

4.1 Unboxing and Inspection

Upon receiving your kit, carefully unbox all components. Check the contents against the packing list and inspect for any visible damage. Ensure the product manual is present.

Video 1: Unboxing and initial setup overview of the spindle motor and VFD kit.

4.2 Spindle Motor Components

Spindle motor with labeled parts: Aviation Plug, Cooling Fan, Metal body, Parameter, Lengthened rotor, Chuck.
Figure 3: Spindle Motor Components (Terminal Box Type)

4.3 VFD Digital Operator Panel Description

VFD with labeled buttons and display: Digital Display, Forward/Reverse Switch Key, Run Key, Stop Reset Button, Shift Key, Frequency Adjustment Key, Programming Key, Select/Confirm Key, Up and Down Keys.
Figure 4: VFD Digital Operator Panel

4.4 Collet Replacement

The ER20 chuck is compatible with 99% standard cutting tools. Follow these steps to replace collets:

  1. Loosen the collet nut using a wrench.
  2. Remove the old collet and insert the new one.
  3. Tighten the collet nut securely.
Animation showing how to remove a collet from the spindle motor.
Figure 5: Collet Removal
Animation showing how to install a collet into the spindle motor.
Figure 6: Collet Installation

5. Wiring Diagram and Connections

Correct wiring is crucial for safe and proper operation. Ensure all connections are tight and secure.

5.1 Main Circuit Terminal Description (VFD)

SymbolFunction Description
R S TInput terminal of AC line power. (220V class, for both single/three phase, single phase connected to any two phases)
U V WOutput terminal of the inverter to the spindle motor.
P+ PrConnector for braking resistor (optional)
EGround terminal: the third method of grounding for 220V and special grounding for 380V of electrical engineering regulations.

5.2 Control Terminal Description (VFD)

Terminal SymbolDescription
NCNOTCONNECTED
MOTriode output
FWDForward
REVReverse
X1, X2, X3, X4Multi-function input 1-4
XGNDCommon terminal of digital control signal
XVCCExternal input 15V
GNDAnalog control signal common terminal
VI1Analog current frequency command
10VPower supply for speed setting
13VExternal power supply
AOAnalog output
NC1Relay normally closed contact
NO1Relay normally open contact
CM1Relay common terminal

5.3 Wiring Diagrams

Ensure correct wiring between the VFD and the spindle motor. Refer to the diagrams below for specific connections based on your voltage and control type.

Wiring diagram for VFD and spindle motor showing 220V/380V input and UVW output to motor.
Figure 7: Main Power and Motor Wiring Diagram
Detailed product wiring diagram for VFD and spindle, including power, motor, ground, and brake resistance connections.
Figure 8: Detailed Product Wiring Diagram
VFD and spindle kit with wiring connections for a control board, showing P00-01 and P07-08 settings.
Figure 9: VFD to Control Board Wiring Example

5.4 External Terminal Control Wiring

The VFD supports various external control methods. Below are common wiring configurations:

5.4.1 Panel Control Wiring

Panel control wiring diagram for VFD and electric motor, showing connections for power, motor output, ground, and optional brake resistance.
Figure 10: Panel Control Wiring Diagram

5.4.2 Three-Wire Control Wiring

Three-wire control wiring diagram for VFD, showing connections for CM1, NO1, NC1, AD, 13V, 10V, VI1, GND, XVCC, XGND, X1-X4, REV, FWD, MO, NC terminals with push buttons.
Figure 11: Three-Wire Control Wiring Diagram

5.4.3 High, Medium, and Low Multi-Speed Control Wiring

High, medium, and low multi-speed control wiring diagram for VFD, showing connections for CM1, NO1, NC1, AD, 13V, 10V, VI1, GND, XVCC, XGND, X1-X4, REV, FWD, MO, NC terminals.
Figure 12: Multi-Speed Control Wiring Diagram

5.4.4 Analog Quantity Control Wiring

Analog quantity control wiring diagram for VFD, showing connections for CM1, NO1, NC1, AO, 13V, 10V, VI1, GND, XVCC, XGND, X1-X4, REV, FWD, MO, NC terminals with a control board.
Figure 13: Analog Quantity Control Wiring Diagram

5.4.5 External Potentiometer with Switch Control Wiring

External potentiometer with switch control wiring diagram for VFD, showing connections for CM1, NO1, NC1, AO, 13V, 10V, VI1, GND, XVCC, XGND, X1-X4, REV, FWD, MO, NC terminals with a 10K speed potentiometer and three-gear two normally open knob.
Figure 14: External Potentiometer Wiring Diagram

6. Operation

6.1 Trial Run

Before operating the VFD and spindle, perform the following checks:

  1. Verify that the power supply is correctly connected to the N/L terminals, not the U.V.W terminals.
  2. Ensure no metal chips or wires are remaining on the inverter substrate or wiring terminals that could cause short circuits.
  3. Confirm all screws are tightly locked and connectors are secure.
  4. Check that the output part has no short circuit or ground fault.

Each time you press the STOP button, the cooling fan will run for about 30 seconds to allow you to observe its working status.

6.2 Parameter Setting Method

To set parameters on the VFD:

  1. Press the PRGM key until the inverter displays "Pyy.xx" to enter the parameter setting state. (yy = parameter group number, xx = parameter number).
  2. Use the ▲ or ▼ keys to select the desired parameter group and number.
  3. Press the SET key to enter the parameter value setting state.
  4. Use the ▲ or ▼ keys to modify the parameter value.
  5. Press the SET key again to save the modified parameter value.
  6. Press the PRGM key to exit the parameter setting state.

Note: Parameters can only be modified when the inverter is stopped (RUN light is off). If the parameter table is locked (P00.13=1), parameters can only be viewed, not modified.

6.3 VFD Parameter Table

The following table lists key parameters for the VFD. Refer to the full PDF manual for a complete list and detailed descriptions.

Parameter NumberNameSetting Range and MeaningFactory Default
P00.00Main digital frequency0.0-600.0HZ400.0HZ
P00.01Start/stop command source0: Operate by panel; 1: External terminal (STOP effective); 2: External terminal (STOP invalid); 3: Modbus RS4850
P00.04VF curve: maximum output frequency1.0-600.0HZ400.0HZ
P00.05VF curve: output frequency at maximum voltage5.0-600.0HZ400.0HZ
P00.13Parameter recovery/locking/read and write0: Allow set; 1: Forbid set (locked); 10: Restore factory defaults0
P03.09Panel potentiometer, upper limit of frequency setting0-120HZ (400HZ)400Hz
P07.078th section frequency setting0.0-600.0HZ400.0HZ

Note: If you need to restore factory settings, set P00.13 to 10, press the confirm key, then turn off the power supply and wait for the inverter lights to go out before powering on. Otherwise, the restoration will be unsuccessful.

If you need to modify parameters, you must set the inverter in a non-working state (RUN light is off). After setting, turn off the power and wait for the inverter lights to go out before powering on, otherwise the setting will be unsuccessful.

7. Maintenance

7.1 Cooling System

The spindle motor features an eddy current air cooling system for continuous operation. The VFD also has a cooling fan.

  • Fan Operating Mode (P12.11):
    1. Start the fan when the motor is running; after the motor stops, turn off the fan with a delay of about 1 minute.
    2. When the temperature is higher than the fan action temperature point (P12.12), the fan will be started immediately; when the temperature is lower than the fan action temperature point, the fan will be turned off after a delay of about 1 minute.
    3. Unconditionally force the fan to start.
    4. The fan does not work.
  • Heat Sink Over Temperature Protection Point (P12.08): Default is 80.
Spindle motor with cooling fan and text indicating 'Extend Motor Life' and 'Fan Cooling System'.
Figure 15: Spindle Cooling System

7.2 General Maintenance Tips

  • Regularly check for loose connections and tighten them as necessary.
  • Keep the spindle motor and VFD clean and free from dust and debris.
  • Inspect the bearings periodically. Bearings have a service life and may need replacement after 0.5 to 1 year depending on frequency and intensity of use.

8. Troubleshooting

This section provides common fault information and troubleshooting methods. If the issue persists, contact technical support.

Error Code/FaultPhenomenonAnalysis and Solutions
Er.00Power failure, power supply voltage is lower than 140VAC1. Check input power voltage (150-250V). Too high voltage damages inverter. 2. For large inertia load, increase deceleration time.
Er.01Power supply voltage is higher than 290VAC, or internal bus voltage is too high1. Inaccurate voltage detection by inverter (requires maintenance). 2. For large inertia load during deceleration, consider external braking resistor.
Er.02The current is too largeCheck for motor short-circuit, correct connection, or excessive mechanical load. Maintenance may be required.
Er.03External PWM circuit errorInternal PWM circuit error. Turn off power for 1 minute, then retry. If persistent, maintenance is required.
Er.04IPM alarm (short circuit)1. Internal power unit module error. 2. Acceleration/deceleration time too short. 3. Inverter overcurrent/overheated. 4. Input voltage too high/low or fluctuates. 5. Inverter/motor power mismatch or incorrect star/delta wiring. 6. Incorrect DC braking parameters. 7. Incorrect VF parameters. 8. Cooling fan damaged/blocked. 9. Gate drive voltage too high/low.
Er.05External fault signal is inputMotor stops, displays code. Reset to clear. No maintenance required.
Er.06Internal data storage errorError in internal data parameter storage. Turn off power for 1 minute, then test.
Er.07Over temperature1. Inverter internal temperature too high (>65°C). 2. Cooling fan not running. 3. Motor short-circuited or overloaded. 4. Poor heat conduction.
Er.08NTC temperature measurement errorInverter internal temperature detection circuit or sensor faulty. Requires repair.
Er.10Power down promptCheck input power voltage is within range.
Er.11RS485 communication is disconnected and error occurs, and the machine stops.Related to parameters P03.03, P03.04.
Er.15Motor overheatedRefer to Er.07 solutions.

9. User Tips

  • Spindle Speed: This is a high-speed spindle. Avoid prolonged operation at low speeds. It is best to operate at or near its rated speed for optimal performance and longevity.
  • VFD Parameter Adjustment: If you need to adjust VFD parameters, refer to the provided video demonstrations for guidance. Users have reported successful parameter adjustments for specific applications like aluminum alloy processing by following video instructions.
  • Continuous Operation: The spindle is designed for continuous operation. If the ambient temperature is within the normal range (-10°C to +50°C) and the spindle surface temperature remains below 150°C, it can work continuously without interruption.
  • Bearing Maintenance: If you notice abnormal sounds from the spindle, it is likely due to bearing issues. Bearings are wear-and-tear components and typically need replacement every 0.5 to 1 year, depending on usage frequency and intensity.
  • Power Supply: Ensure your power supply (110V, 220V, or 380V) matches the VFD and spindle requirements. The kit is designed for plug-and-play use in various regions.

10. Warranty and Support

10.1 Warranty Information

The VFD comes with a 1-year warranty from the date of purchase.

10.2 Braking Resistor Policy

Please select the resistance and frequency of use specified by our company. If you use braking resistors and brake modules not provided by our company, and this causes damage to the inverter or other equipment, our company will not be held responsible.

10.3 Customer Support

For any further questions, technical assistance, or to inquire about specific braking resistor configurations, please contact your local dealer or the HLTNC Official Store.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.