QIACHIP KT19-117S-4+KR1204B-4

Contents

QIACHIP 433Mhz RF Remote Control Circuit User Manual

Model: KT19-117S-4+KR1204B-4

Introduction

This manual provides detailed instructions for the QIACHIP 433Mhz RF Remote Control Circuit, including the 4-channel wireless switch receiver (Model: KR1204B-4) and keyfob transmitter (Model: KT19-4). This system is designed for universal use with various devices such as lighting, electric doors, automated curtains, and other switch-controlled applications. It covers product specifications, wiring diagrams, operating modes, programming procedures, and important safety information. Please read this manual thoroughly before installation and operation.

Specifications

Remote Control (Transmitter) - Model: KT19-4

Feature Specification
Model Number KT19-4
Working Voltage DC 3V
Working Current <25mA
Working Frequency 433MHZ
Transmitting Power +13dbm
Encoding Format 1527 encoding (EV1527)

Remote control specifications table Image: Remote control specifications.

Remote control dimensions: 55mm x 30mm x 10mm Image: Remote control dimensions (55mm x 30mm x 10mm).

Receiver (Wireless Switch) - Model: KR1204B-4

Feature Specification
Model Number KR1204B-4
Input Voltage DC 5V-80V
Working Current ≤10A
Quiescent Current 5mA
Frequency 433.92MHZ
Output Current ≤10A
Receiving Sensitivity >104dbm
Supported Encoding Format EV1527 (Learning Code 1527)
Wiring Method NC COM NO
Working Mode Momentary, Toggle, Latching Time delay
Maximum Paired Remotes No more than 20 pcs
Working Temperature -10~+80°C
Size 73x55x30 (mm)

Receiver dimensions: 73mm x 55mm x 30mm Image: Receiver dimensions (73mm x 55mm x 30mm).

Package Contents

Different package options are available:

  • Package List 1: 1* KT19-4 433Mhz Remote Control (includes Battery)
  • Package List 2: 1* KR1204B-4 Receiver Module (includes Shell)
  • Package List 3: 1* KT19-4 433Mhz Remote Control (includes Battery) + 1* KR1204B-4 Receiver Module (includes Shell)
  • Package List 4: 2* KT19-4 433Mhz Remote Control (includes Battery) + 1* KR1204B-4 Receiver Module (includes Shell)
  • Package List 5: 5* KT19-4 433Mhz Remote Control (includes Battery) + 1* KR1204B-4 Receiver Module (includes Shell)

Setup and Wiring

Important Safety Note: Always ensure power is OFF before performing any wiring. Do not install with electricity.

Receiver Components Overview

The receiver board (KR1204B-4) features an antenna, a learning button, an indicator LED, and terminal blocks for power and relay outputs.

Top view of the KR1204B-4 receiver board showing relays, learning button, and terminals. Image: Top view of the KR1204B-4 receiver board.

Close-up of receiver wiring terminals labeled +V, GND, NO, COM, NC. Image: Close-up of receiver wiring terminals.

  • +V: Connect to the positive terminal of the DC 5V-80V power supply.
  • GND: Connect to the negative terminal of the DC 5V-80V power supply.
  • NO (Normally Open): Output terminal for the relay.
  • COM (Common): Common terminal for the relay.
  • NC (Normally Closed): Output terminal for the relay.

Wiring Diagram for DC Lamps

This diagram illustrates how to connect DC lamps to the receiver for control.

Wiring diagram showing a 4-channel receiver connected to four DC lamps. DC12V+ and DC12V- are connected to the power input, and each lamp is connected between a COM terminal and either NO or NC, depending on desired behavior. Image: Wiring diagram for controlling four DC lamps with the receiver.

Wiring Diagram for Two DC Motors

This diagram shows how to connect two DC motors to the receiver for control.

Wiring diagram showing a 4-channel receiver connected to two DC motors. DC12V+ and DC12V- are connected to the power input, and each motor is connected to two COM terminals and two NO/NC terminals to allow for directional control or on/off. Image: Wiring diagram for controlling two DC motors with the receiver.

Operating Modes

The wireless remote control switch supports three working modes:

  • Momentary Mode (Jog):

    When the remote button is pressed and held, the corresponding relay on the receiver turns ON. When the remote button is released, the relay turns OFF.

  • Toggle Mode (Self-locking):

    Press the remote button once, the corresponding relay on the receiver turns ON. Press the same remote button again, the relay turns OFF.

  • Latching Mode (Interlock):

    In this mode, pressing remote button A turns ON the relay corresponding to A. Pressing remote button B turns OFF the relay corresponding to A and turns ON the relay corresponding to B. This creates an interlock where only one relay can be active at a time. To turn off all relays in latching mode, press remote buttons A and B simultaneously.

Note: All working modes require a QIACHIP brand remote control (transmitter) and receiver. Compatibility with other brands is not guaranteed.

Programming the Remote Control

Note: The working mode can only be set when the LED indicator on the receiver is lit.

Set Momentary Mode (Jog)

  1. Press the receiver's learning button once. The LED on the receiver will light up, indicating it's in setting state.
  2. Press any button on your remote control (e.g., button A) once. The receiver's LED indicator will flash and then turn off.
  3. After approximately 3 seconds, the LED indicator will turn on again, confirming successful programming in Momentary mode.

Set Toggle Mode (Self-locking)

  1. Press the receiver's learning button twice. The LED on the receiver will light up, indicating it's in setting state.
  2. Press any button on your remote control (e.g., button A) once. The receiver's LED indicator will flash and then turn off.
  3. After approximately 3 seconds, the LED indicator will turn on again, confirming successful programming in Toggle mode.

Set Latching Mode (Interlock)

For Latching mode, you need to program two different buttons on the remote: one for ON and one for OFF for each channel.

  1. Press the receiver's learning button three times. The LED on the receiver will light up, indicating it's in setting state.
  2. Press remote button A (for ON). The LED will flash 5 times.
  3. Press remote button B (for OFF). The LED will flash 5 times.
  4. After approximately 3 seconds, the LED indicator will turn on again, confirming successful programming in Latching mode. (e.g., A = ON, B = OFF)

Programming Demonstration Video

Video: A demonstration of clearing the code and programming the receiver in Momentary and Toggle modes.

Reset Function (Clear Code)

To clear all matched remote controls from the receiver's memory:

  1. Press the receiver's learning button 8 times.
  2. The receiver's LED indicator will flash, then turn off, indicating that all stored remote control data has been cleared. All previously paired remotes will no longer operate the receiver.

User Tips

  • Mode Flexibility: The receiver's working mode (Momentary, Toggle, Latching) is set for the entire receiver, not per button. If you need different behaviors for different channels, you would typically use separate receivers or a more advanced multi-mode controller.
  • Input Voltage Clarification: The receiver supports a wide input voltage range of DC 5V-80V. This means it is compatible with 6V, 12V, 24V, and up to 80V DC power supplies.
  • Remote Pairing: If you are having trouble pairing, ensure you are pressing the learning button the correct number of times for your desired mode and then pressing the remote button promptly. The LED indicator provides visual feedback during the process.

Troubleshooting

  • Remote Not Responding:
    • Check the remote control battery. If the voltage is low, the remote range may decrease or it may stop working.
    • Ensure the remote is properly paired to the receiver in the desired operating mode. If unsure, try clearing the code and reprogramming.
  • Short Remote Control Distance or Intermittent Operation:
    • Avoid placing the receiver near large metal surfaces, other electronic devices, or strong electromagnetic fields, as these can cause interference.
    • Ensure the receiver's antenna is not obstructed or damaged.
  • Receiver LED Not Lighting Up During Programming:
    • Verify the receiver is correctly powered within the DC 5V-80V range.
    • Ensure the learning button is functioning correctly.

Important Notes and Safety Precautions

  • Power Off Before Wiring: Always disconnect power to the receiver and any connected devices before performing any wiring or modifications. Failure to do so can result in electric shock or damage to the device.
  • Use Correct Voltage: Ensure the input voltage to the receiver is within the specified DC 5V-80V range.
  • Avoid Abnormal Use: Do not use this product in ways other than its intended purpose. Abnormal use can reduce product performance and lifespan, and may pose safety risks.
  • Environmental Considerations: Keep the device away from moisture, extreme temperatures, and corrosive environments.

Warranty and Support

For warranty information, technical support, or additional services, please visit the official QIACHIP website at www.qiachip.com.

A user manual in PDF format is also available for download: Download User Manual (PDF)


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.