Allsome BG-5168E

Contents

ALLSOME BG-5168E Mini Electric Drill Press User Manual

Model: BG-5168E

Brand: Allsome

Front view of the ALLSOME BG-5168E Mini Electric Drill Press

Front view of the ALLSOME BG-5168E Mini Electric Drill Press.

1. Introduction

Dear Customer,

This bench drill with a drill chuck range of up to 13mm is a high-grade precision drilling tool designed for a range of industrial materials. Before using the drill, read the enclosed safety regulations and operating instructions for information on the safe and proper operation of the drill.

The bench drill was designed for maximum precision, performance and ease of use and offers an impressive range of characteristics:

  • Plano-milled workbench made of high-grade, ultra-ribbed aluminium die-cast
  • Sturdy chromium-plated steel column
  • Lock-type bit stop with dial
  • Three-speed operation geared to drive belt position, with six-fold torque in lower speed range
  • Drill spindle with high-grade, precision ball bearings

2. Safety Instructions

WARNING: Ensure that the drill is securely mounted on a stable support before putting it into operation.

CAUTION: Unplug the drill before changing application tools and before all adjusting operations!

CAUTION: Unplug drill before performing any operation that requires access to internal components or adjustments. Never operate the drill without the protective cover in place.

IMPORTANT: Always secure the extension arm against falling during adjustments.

CAUTION: Unplug drill before performing any maintenance operation!

3. Specifications

Side view of the drill press with specifications label

Side view of the drill press with a label indicating key specifications.

Technical Data
Attribute Value
Product Name5168E Drill Press
Power680W
Voltage220V
Frequency50Hz
Stroke Length60mm
Working Radius143mm
Clamping Capacity1-13mm
Rotation Rate (No-Load Speed)I: 1100r/min, II: 2500r/min, III: 4500r/min
Drilling Capacity (Iron)8mm
Drilling Capacity (Wood)30mm
Size of Operation Platform205mm x 205mm
Upright Column45mm x 500mm
Max. Bench Surface Distance to Drill Chuck230mm
Centre Sleeve Lift63mm
Weight10kg
Power SourceAC
Drill TypeDrill Press
ApplicationElectric drill, Renovation Team
Number of Items1
ElectrifiedYes
MovableYes
HandheldNo
Battery IncludedNo
High-concerned chemicalnone
is_customizedYes
Rated TorqueNormal
OriginMainland China
CertificationNONE
Dimensional drawing of the drill press

Dimensional drawing of the drill press, showing height (550mm), base width (205mm), base depth (205mm), and distance from column to chuck (150mm).

4. Setup

4.1 General Overview of Components

Diagram showing the components of the drill press with numbered parts

Diagram showing the components of the drill press with numbered parts for reference.

Component List
No. Component
1Chuck key
2Fastening bolt for cover hood
3Cover hood
4Drill lever
5On/off switch
6Drill chuck
7Depth display
8Bit stop locking bolt
9Drill column locking bolt
10Extension arm locking bolt
11Extension arm
12Belt
13Drill column
14Work table
15Speed control
16Motor pulley
17Drill pulley
18Bit stop with dial

4.2 Clamping Bit in Drill Chuck

  1. Insert chuck key in drill chuck (6).
  2. Turn chuck key counter-clockwise to open chuck.
  3. Push bit into chuck to bit stop.
  4. Turn chuck key clockwise to close chuck.

NOTE: Close chuck without completely securing bit to check for proper seating of bit, then secure bit tightly. REMEMBER TO REMOVE CHUCK KEY FOLLOWING CHUCKING.

4.3 Removing and Installing Drill Chuck

NOTE: We recommend collet chucks (available as accessories) for precision-true drilling operations that the standard drill chuck is unable to perform. When using collet chucks, it is first necessary to remove the standard drill chuck.

  1. Lock spindle to key surface (14) using a fork.
  2. To unscrew chuck (counter-clockwise) or to screw chuck in (clockwise), insert chuck key, which acts as a lever.

4.4 Re-positioning Complete Extension Arm

IMPORTANT: Secure extension arm against falling.

  1. Release knurled bolt (10) and knurled bolt (9).
  2. Move complete extension arm to desired position.
  3. Re-tighten knurled bolts.

5. Operating Instructions

5.1 Set Spindle Speed

CAUTION: Unplug drill before performing this operation! Never operate drill without protective cover.

NOTE: Optimal performance results from uniform, correct speed and not from excessive pressure.

The drill press features three-speed operation based on belt position:

  • Belt position I: 1100 RPM
  • Belt position II: 2500 RPM
  • Belt position III: 4500 RPM

5.2 Adjusting Belt Tension

CAUTION: Unplug drill before performing this operation!

NOTE: When changing drill speed, it is not necessary to re-tension the belt. Tension the belt no tighter than necessary, i.e., tighten until there is no more slack. An over-tensioned belt distends over longer periods of inactivity and reduces motor output.

  1. Unscrew knurled bolt (2) and remove cover hood (3).
  2. Loosen both bolts (1) by one rotation.
  3. Using a screwdriver, lever out the motor to the rear until the desired belt tension has been attained.
  4. Tighten both bolts.
  5. Install cover hood. Tighten knurled bolts (2).

NOTE: Once the belt is properly tensioned (between motor axle and drill spindle), you should be able to easily re-position it by hand. When changing speed, it is not necessary to re-tension the belt.

5.3 Utilising Depth Stop

Proceed as follows to adjust the maximum drilling depth:

  1. Loosen locking bolt (8).
  2. Lower drill spindle until bit contacts workpiece.
  3. Set desired drilling depth on dial (7) and re-tighten locking bolt.

5.4 Usage Scenarios

The ALLSOME BG-5168E Mini Electric Drill Press is versatile for various applications, including drilling into wood, metal, and plastic. It can be used with different accessories like vises for enhanced precision.

Drill press in various applications
Drill press in various applications.
Drill press with workpiece clamped in a vise
Drill press with workpiece clamped in a vise.
Drill press with a cross-slide vise
Drill press with a cross-slide vise for precision.

6. Maintenance

CAUTION: Unplug drill before performing any maintenance operation!

  • Lubricate the centre sleeve guide every 10 operating hours using a few drops of machine oil.
  • Following use, the drill must be thoroughly cleaned using a whisk or brush to remove all swarf.
  • All dirt deposits on the drill must be routinely removed using a rag.
  • During longer periods of inactivity, the drive belt must be removed to prevent deformation and erratic function.
  • If, after it has been in use for a certain time, noises are heard on touching the tailstock quill, this indicates play in the tailstock quill, which should be taken up by slightly tightening the screw.

7. Troubleshooting

  • Motor Heating Under Load: While the manual does not specify engine heating under load, ensure proper ventilation around the motor and avoid applying excessive pressure during drilling. If overheating persists, reduce load or allow the machine to cool.
  • Excessive Spindle Runout: The drill spindle is equipped with high-grade, precision ball bearings. If you experience excessive runout, ensure the drill bit is properly seated in the chuck and the chuck is tightened securely. Check for any damage to the chuck or spindle.
  • Belt Slippage or Incorrect Speed: Refer to the 'Adjusting Belt Tension' and 'Set Spindle Speed' sections to ensure the belt is correctly positioned and tensioned for the desired RPM.

8. User Tips

  • This drill press offers good performance for its value, making it a satisfactory choice for various tasks.
  • It is particularly well-suited for working with wood, as noted by users.
  • For optimal results, ensure your workpiece is securely clamped before drilling.

9. Frequently Asked Questions (FAQ)

Q: Is the engine heated at load?
A: The manual does not specify engine heating under load. Ensure proper ventilation and avoid excessive pressure during operation to prevent overheating.
Q: Is the vise included?
A: The product package typically includes the drilling machine only. Vises are usually sold separately as accessories. Images showing vises are for demonstration of potential setups.
Q: Are the gear reducer gears metal?
A: The drill press uses a belt-driven system for speed regulation, not direct gears for reduction. User feedback indicates the pulleys are aluminum.
Q: I need a belt and a chuck, where can I buy them?
A: Replacement belts and chucks can typically be sourced from the manufacturer's authorized dealers or specialized tool suppliers. For detailed part numbers, please refer to the official user manual PDF: ALLSOME BG-5168E User Manual (PDF).
Q: What is the spindle runout?
A: The technical specifications do not explicitly state the spindle runout. However, the description mentions "high-grade, precision ball bearings" for the drill spindle, indicating a focus on precision. If experiencing excessive runout, ensure the drill bit is properly seated and the chuck is tightened correctly.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the complete official user manual PDF or contact the seller directly. The official user manual PDF can be found here: ALLSOME BG-5168E User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.