DEKO DKSG55K1/DKSG20K2

Contents

DEKO HVLP Electric Paint Sprayer Instruction Manual

Models: DKSG55K1 (AC Powered) & DKSG20K2 (DC Battery Powered)

1. Introduction

Thank you for choosing the DEKO HVLP Electric Paint Sprayer. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your DKSG55K1 (AC powered) or DKSG20K2 (DC battery powered) paint sprayer. Please read this manual thoroughly before first use and keep it for future reference.

DEKO HVLP Spray Gun with accessories
DEKO HVLP Spray Gun (Model DKSG55K1 shown) with included accessories.

2. Safety Information

Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury. This includes, but is not limited to:

  • Wear appropriate personal protective equipment (PPE) such as safety glasses, gloves, and a respirator mask.
  • Ensure the work area is well-ventilated.
  • Keep children and bystanders away while operating the sprayer.
  • Do not spray flammable materials near open flames or ignition sources.
  • Always disconnect the power (unplug AC model or remove battery from DC model) before cleaning, maintenance, or changing accessories.
  • Refer to paint manufacturer's safety data sheets (SDS) for specific handling instructions.

3. Product Components & Unpacking

Your DEKO HVLP Electric Paint Sprayer is designed for easy assembly and cleaning. Familiarize yourself with the main components:

Exploded view of the detachable spray gun showing components and nozzle sizes
Detachable gun components: Union Nut, Air Cap, Nozzles, Trigger, Release Button, Jog Wheel, 800ml Container, Flow Control Knob.

3.1. Included Items (AC Set - DKSG55K1)

  • DKSG55K1 Spray Gun
  • Cleaning Needle
  • (3) Spray Nozzles & Jets (1.0mm, 1.8mm, 2.5mm)
  • Mask
  • Viscosity Cup
  • (2) Rubber Gloves
  • (5) Paint Strainers
  • Spanner
  • Packing Case

3.2. Included Items (DC Set - DKSG20K2)

  • DKSG20K2 Spray Gun
  • BATTERY20VY 1.5 Battery
  • Charger
  • Cleaning Needle
  • (3) Spray Nozzles & Jets (1.0mm, 1.8mm, 2.5mm)
  • Mask
  • Viscosity Cup
  • (2) Rubber Gloves
  • Spanner
  • (5) Paint Strainers
  • Packing Case
Image showing included items for both AC and DC sets
Visual representation of items included in the AC and DC sets.

4. Setup & Preparation

4.1. Assembly

  1. Ensure the spray gun is disconnected from power (unplugged or battery removed).
  2. Unscrew the union nut and air cap from the front of the gun.
  3. Select the appropriate nozzle for your paint and project (see 4.2 Nozzle Selection). Insert the chosen nozzle into the gun body.
  4. Reattach the air cap and union nut, tightening securely.
  5. Attach the 800ml container to the bottom of the gun body by screwing it on firmly.

4.2. Nozzle Selection

The sprayer comes with three nozzle sizes to accommodate various paint types and desired finishes:

  • 1.0mm / 1.8mm Nozzles: Ideal for thin paints such as sealers and varnish.
  • 2.5mm Nozzle: Suitable for thicker materials like latex paint and chalk-type paint.
Nozzle size options for versatility
Choose the correct nozzle size for optimal spray performance.

4.3. Paint Preparation & Viscosity Test

Proper paint thinning is crucial for optimal spray performance and to prevent clogging. Always follow the paint manufacturer's recommendations for thinning. Use the included viscosity cup to test the paint's consistency.

  1. Fill the viscosity cup with the prepared paint.
  2. Measure the time it takes for the paint to completely drain from the cup.
  3. The recommended viscosity for this sprayer is 8-12 seconds. If the paint drains too quickly, it's too thin; if it drains too slowly, it's too thick and needs further thinning.
  4. Adjust paint consistency by adding appropriate thinner (water for water-based paints, mineral spirits for oil-based paints) and re-test until the desired viscosity is achieved.

4.4. Filling the Container

Once the paint is prepared, carefully pour it into the 800ml container. Do not overfill. Securely screw the container back onto the spray gun.

800ml large capacity paint container
The 800ml container provides ample capacity for various projects.

5. Operation

5.1. Powering On

  • For DKSG55K1 (AC Model): Plug the power cord into a suitable electrical outlet.
  • For DKSG20K2 (DC Model): Ensure the battery is fully charged and securely inserted into the battery slot.

5.2. Adjusting Spray Patterns

Your sprayer offers three adjustable spray patterns to suit different applications:

  • Horizontal: For vertical surfaces.
  • Vertical: For horizontal surfaces.
  • Circular: For small areas, corners, or intricate details.

To change the spray pattern, rotate the air cap to align the desired pattern with the nozzle. Always test the spray pattern on a scrap piece of material before applying to your project.

Image showing horizontal, vertical, and circular spray patterns
Adjust the air cap to select between horizontal, vertical, and circular spray patterns.

5.3. Adjusting Flow Control

The flow control knob (Jog Wheel) located on the side of the spray gun allows you to adjust the paint output volume. Turn the knob clockwise to increase flow and counter-clockwise to decrease flow. Start with a lower setting and gradually increase until the desired coverage is achieved.

5.4. Spraying Technique

  1. Hold the spray gun approximately 200-250mm (8-10 inches) from the surface.
  2. Maintain a consistent distance and speed while spraying to ensure an even coat.
  3. Use smooth, overlapping strokes. Release the trigger at the end of each stroke to avoid paint buildup.
  4. For best results, apply multiple thin coats rather than one thick coat.
DEKO HVLP Electric Paint Sprayer in use, demonstrating spray
Demonstration of the HVLP Electric Paint Sprayer in action.

6. Maintenance & Cleaning

Thorough cleaning after each use is essential to prolong the life of your spray gun and ensure consistent performance.

  1. Disconnect Power: Always unplug the AC model or remove the battery from the DC model before cleaning.
  2. Empty Container: Unscrew the paint container and pour any remaining paint back into its original can.
  3. Initial Rinse: Fill the container with an appropriate cleaning solution (water for water-based paints, mineral spirits or paint thinner for oil-based paints). Spray the cleaning solution through the gun into a waste container until it runs clear.
  4. Disassemble: Detach the gun body from the motor unit (if applicable), unscrew the union nut, air cap, and remove the nozzle.
  5. Thorough Cleaning: Clean all disassembled parts (nozzle, air cap, container, suction tube) with the appropriate cleaning solution and the included cleaning needle/brush. Pay special attention to small orifices to prevent clogging.
  6. Wipe Down: Wipe the exterior of the spray gun with a damp cloth.
  7. Dry & Reassemble: Ensure all parts are completely dry before reassembling. Store the spray gun in a clean, dry place.

7. Troubleshooting

ProblemPossible CauseSolution
No spray or weak sprayNozzle clogged, paint too thick, air cap blocked, suction tube blocked, low paint level.Clean nozzle and air cap. Thin paint to correct viscosity. Check and clear suction tube. Refill paint container.
Uneven spray patternNozzle partially clogged, air cap not properly aligned, inconsistent spraying technique.Clean nozzle. Ensure air cap is correctly aligned for desired pattern. Practice consistent strokes.
Paint drips or runsPaint too thin, spraying too close to surface, too much paint flow.Thicken paint slightly. Increase spraying distance. Reduce paint flow with the control knob.
Motor runs but no paint spraysSuction tube not immersed in paint, air leak, nozzle/air cap completely blocked.Ensure suction tube is in paint. Check all connections for tightness. Thoroughly clean nozzle and air cap.
DKSG20K2 (DC) not powering onBattery not charged, battery not inserted correctly, faulty battery/charger.Charge battery fully. Reinsert battery firmly. Test battery/charger if possible.

8. Specifications

8.1. DKSG55K1 (AC Powered)

FeatureSpecification
ModelDKSG55K1
TypeHVLP
Voltage230/110V
Frequency50/60Hz
Rated Speed30000rpm
Container Volume800ml
Nozzle Size1.0mm/1.8mm/2.5mm
Air Flow160L/MIN
Paint Flow100-200ml/min
Max. Viscosity8-12s
Wire Length1.8m
Product Weight1.568kg
Main features and specifications for DKSG55K1
Key specifications for the DKSG55K1 model.

8.2. DKSG20K2 (DC Battery Powered)

FeatureSpecification
ModelDKSG20K2
TypeHVLP
Voltage18V
Battery1500MAH
Rated Speed30000rpm
Rated Power120W
Container Volume800ml
Nozzle Size1.0mm/1.8mm/2.5mm
Air Flow160L/MIN
Paint Flow100-200ml/min
Max. Viscosity8-12s
Spraying Distance200-250mm
Product Weight1.68kg
Main features and specifications for DKSG20K2
Key specifications for the DKSG20K2 model.

9. User Tips

  • Paint Compatibility: While suitable for many paints, always check the paint manufacturer's recommendations for spray application and thinning. For emulsion paints, ensure proper thinning to achieve the recommended viscosity.
  • Test First: Before starting your main project, always test the spray pattern and flow on a piece of scrap material to ensure optimal settings and prevent mistakes.
  • Clean Immediately: The most common cause of sprayer issues is dried paint. Clean your sprayer immediately after each use to prevent clogs and ensure longevity.
  • Wear Protection: Always wear a mask, safety glasses, and gloves to protect yourself from paint fumes and overspray.

10. Warranty & Support

Your DEKO HVLP Electric Paint Sprayer comes with a 1-Year Limited Warranty from the date of purchase. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please contact DEKO customer service through the retailer where you purchased the product. Provide your model number and a detailed description of the issue to expedite service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.