1. Overview
The AISET NG series is a reliable, cost-effective digital temperature controller, designed for temperature measurement and automatic control in industrial workshops, production lines, laboratories, and general automation equipment. It features simple operation, stable performance, high control accuracy, and strong adaptability, widely applied in various heating, cooling, and constant temperature control scenarios, fully complying with EU safety standards (EMC, LVD, WEEE directives) and AliExpress EU compliance requirements.
2. Important Safety Warnings
Read carefully before use to avoid injury, equipment damage, or non-compliance with EU regulations and AliExpress requirements.
- This product is for industrial use only, not for household use. Keep out of reach of children and untrained personnel to prevent accidents.
- WARNING: Always turn off the power supply before wiring, maintenance, disassembly, or cleaning to prevent electric shock and equipment damage.
- WARNING: Do not use the product beyond the rated parameters (voltage, temperature, load), which may cause fire, electric shock, or permanent product damage.
- WARNING: Avoid installing the controller in flammable, explosive, humid, dusty, or corrosive environments to eliminate potential safety hazards.
- WARNING: The controller must be grounded correctly in accordance with EU EMC and LVD directives; mandatory grounding is required for safe use and compliance with AliExpress requirements.
- WARNING: Do not modify, disassemble, or repair the product without authorization; any unauthorized operation will void the warranty and may violate EU regulations.
- WARNING: In case of abnormal operation (smoke, peculiar odor, overheating, or display failure), turn off the power immediately and stop using it, then contact professional maintenance personnel.
- WARNING: Disposal of this product must comply with EU WEEE directives; do not discard it as household waste. Please hand it over to qualified recycling institutions.
3. Setup and Wiring Instructions
3.1 Power On
Connect the power supply according to the wiring diagram (ensure correct grounding to meet EU compliance), then turn on the power switch. The AISET NG controller will automatically display the current measured temperature after power-on, allowing quick monitoring of real-time temperature status.
3.2 Wiring Instructions
Please turn off the power before wiring to avoid electric shock. The basic wiring of the AISET NG series is as follows (please refer to the product label for specific details to ensure correct connection and EU compliance for AliExpress):
- Power Terminal (L/N): Connect to AC 100~240V power supply, ensuring stable power input to avoid equipment malfunctions.
- Input Terminal (IN): Connect to thermocouple or RTD temperature sensor, ensuring tight connection for accurate signal transmission.
- Output Terminal (OUT): Connect to the load (such as heater, cooler, etc.), and match the load type with the controller's output mode.
- Ground Terminal (PE): Mandatory grounding (complies with EU safety regulations) to ensure safe use and prevent electrical hazards, which is required for AliExpress EU sales.
WARNING: Wrong wiring (especially no grounding) may cause electric shock, fire, or product damage, violate EU regulations, and fail to meet AliExpress requirements. Please double-check the wiring before power-on.
4. Operating Instructions
4.1 Set Target Temperature
- Press the "SET" key once; the display will flash, and you will enter the target temperature setting mode.
- Press the "▼" (down) or "▲" (up) key to adjust the target temperature to your required value, with intuitive operation and precise step adjustment.
- Press the "SET" key again to confirm and exit the setting mode, and the NG series controller will start automatic temperature control immediately.
4.2 Display Introduction
- Normal mode: The left display shows the current measured temperature, and the right display shows the target temperature, with a clear and easy-to-read interface.
- Setting mode: The flashing display indicates the parameter being set (only the target temperature is adjustable in simple operation, reducing complexity).
- Alarm mode: The alarm indicator will light up when the temperature exceeds the set range (optional function, ensuring safe operation).
5. Maintenance
- Install the NG series controller in a dry and ventilated place, away from high temperature, humidity, strong electromagnetic interference, and flammable/explosive materials.
- Regularly check the wiring, sensor connection, and controller status to ensure stable operation, EU compliance, and meet AliExpress requirements.
- Clean the controller surface with a dry, soft cloth; do not use corrosive cleaners to avoid damaging the product.
6. Troubleshooting
- CAUTION: If the controller fails (e.g., abnormal operation, smoke, peculiar odor, overheating, or display failure), turn off the power immediately and contact professional maintenance personnel; do not attempt to repair it yourself to avoid safety risks.
7. Key Specifications
| Item | Parameter |
|---|---|
| Measurement Range | -50°C ~ 999°C |
| Control Accuracy | ±0.1°C |
| Input Signal | Thermocouple (K/J/T/E), RTD (PT100) |
| Output Mode | Relay output, SSR drive (optional) |
| Operating Voltage | AC 100~240V, 50/60Hz (Complies with EU LVD directive) |
| Working Temperature | 0°C ~ 50°C |
| Protection Class | IP40 |
8. User Tips
No specific user tips or common questions were available from provided reviews or Q&A content.
9. Warranty
The AISET NG series temperature controller provides a 12-month warranty from the date of delivery. Under normal use and installation in accordance with this manual (and EU regulations, AliExpress requirements), free repair or replacement service is provided for defects caused by materials or workmanship. The warranty does not cover damage caused by improper operation, wrong wiring, unauthorized disassembly, non-compliance with EU regulations, or external factors.
10. Support and Further Information
This is a simplified EU compliance manual. For detailed operation steps, parameter settings, and advanced functions, please refer to the full-version manual. Ensure compliance with the target EU country's language requirements when selling.
A comprehensive user manual in PDF format can be viewed or downloaded from the following link: AISET NG Series Temperature Controller User Manual (PDF).