QIACHIP KT19-117S-4+KR1204B-4

Contents

QIACHIP 433MHz Universal Wireless Remote Control Switch System

Model: KT19-117S-4 (Transmitter) & KR1204B-4 (Receiver)

Brand: QIACHIP

1. Introduction

This manual provides detailed instructions for the QIACHIP 433MHz Universal Wireless Remote Control Switch System, comprising a transmitter (remote control) and a receiver module. This system is designed for various applications including lighting, electric doors, automated curtains, and general switching needs. Please read this manual carefully before installation and operation to ensure correct usage and optimal performance.

2. Safety Information

  • Do NOT install with electricity: Always ensure the power supply is disconnected before wiring to prevent electric shock and damage to the device.
  • Power Supply: Ensure the input voltage to the receiver module is within the specified range (DC 5V-80V).
  • Remote Control Battery: If the remote control's range decreases, replace the battery promptly.
  • Interference: Avoid installing the device near large metal surfaces, strong electromagnetic fields, or other electronic devices that may cause interference, as this can reduce the remote control's effective range.
  • Intended Use: Do not use this product for purposes other than its intended design. Improper use may lead to reduced performance, shortened lifespan, or safety hazards.

3. Product Overview

The QIACHIP wireless remote control system consists of a 4-channel receiver module and a 4-button remote control transmitter.

3.1 Receiver Module (KR1204B-4)

The receiver module features a learning button for programming, an indicator LED, and screw terminals for wiring. It supports various working modes to suit different applications.

QIACHIP KR1204B-4 Receiver Module Board
Figure 1: QIACHIP KR1204B-4 Receiver Module Board
QIACHIP KR1204B-4 Receiver Module with protective casing
Figure 2: QIACHIP KR1204B-4 Receiver Module with protective casing

3.2 Remote Control Transmitter (KT19-117S-4)

The remote control is a 4-button device (A, B, C, D) used to send wireless signals to the receiver module. It is compact and includes a keychain for convenience.

QIACHIP KT19-117S-4 Remote Control Transmitter front and back
Figure 3: QIACHIP KT19-117S-4 Remote Control Transmitter
QIACHIP KT19-117S-4 Remote Control Transmitter dimensions
Figure 4: Remote Control Transmitter Dimensions

4. Specifications

4.1 Receiver Module (KR1204B-4)

FeatureSpecification
Input VoltageDC 5V-80V
Working Current≤10A
Quiescent Current5mA
Frequency433MHz / 433.92MHZ
Output Current≤10A
Receiving Sensitivity>104dbm
Support Encoding FormatEV1527 / Learning Code (1527)
Wiring MethodNC COM NO (+V GND)
Working ModeMomentary, Toggle, Latching Time delay
Maximum Paired RemotesNo more than 20 pcs
Working Temperature-10°C to +80°C
Dimensions73 x 55 x 30 mm

4.2 Remote Control Transmitter (KT19-117S-4)

FeatureSpecification
Model NumberKT19-117S-4
Working VoltageDC 3V
Working Current<25mA
Working Frequency433MHz
Transmitting Power+13dbm
Encoding Format1527 encoding

5. Setup and Wiring

Before proceeding with wiring, ensure all power sources are disconnected. Incorrect wiring can damage the device or cause injury.

5.1 Wiring Instructions for Receiver Module (KR1204B-4)

The receiver module has terminals for power input and relay outputs:

  • +V: Connect to the positive terminal of the DC 5V-80V power supply.
  • GND: Connect to the negative terminal of the DC 5V-80V power supply.
  • NO (Normally Open): Output terminal, normally open end of the relay.
  • COM (Common): Output terminal, common end of the relay.
  • NC (Normally Closed): Output terminal, normally closed end of the relay.

5.2 Wiring Diagrams

Below are common wiring diagrams for different applications. Always ensure power is off before making any connections.

5.2.1 Wiring for DC Lamps

Wiring diagram for connecting DC lamps to the receiver module
Figure 5: DC Lamp Wiring Diagram. Connect lamps to the relay outputs (NO, COM, NC) and power the module with DC 5V-80V.

Warning: Do not install with electricity.

5.2.2 Wiring for Two DC Motors

Wiring diagram for connecting two DC motors to the receiver module
Figure 6: Two DC Motors Wiring Diagram. Connect motors to the relay outputs (NO, COM, NC) for directional control and power the module with DC 5V-80V.

Warning: Do not install with electricity.

6. Operating Modes

The system supports three main working modes:

  1. Momentary Mode (Jog):

    When the remote button is pressed and held, the corresponding relay on the receiver turns ON. When the remote button is released, the relay turns OFF.

  2. Toggle Mode (Self-locking):

    Press the remote button once to turn the corresponding relay ON. Press the same remote button again to turn the relay OFF.

  3. Latching Mode (Interlock):

    Press remote button A to turn ON the relay corresponding to A. Press remote button B to turn OFF relay A and turn ON relay B. This mode ensures only one relay is active at a time. If remote buttons A and B are pressed simultaneously, the receiver will turn OFF.

7. Programming the Remote Control (Learning Code)

Note: Programming can only be performed when the receiver's LED indicator is lit.

7.1 Clearing All Paired Remotes (Reset Function)

To clear all previously paired remote controls from the receiver's memory:

  1. Press the learning button on the receiver module 8 times.
  2. The receiver's LED indicator will flash and then turn off, indicating that all remote control data has been cleared.

After clearing, no remote control will be able to operate the receiver until re-programmed.

Video 1: Demonstration of clearing codes and programming momentary mode.

7.2 Setting Momentary Mode (Jog)

  1. Press the learning button on the receiver module once.
  2. Wait for the LED on the receiver to light up, indicating it has entered the setting state.
  3. Press a button on the remote control (e.g., button A) once. The receiver's LED indicator will flash and then turn off.
  4. Momentary mode is now successfully set for that button.

7.3 Setting Toggle Mode (Self-locking)

  1. Press the learning button on the receiver module twice.
  2. Wait for the LED on the receiver to light up, indicating it has entered the setting state.
  3. Press a button on the remote control (e.g., button A) once. The receiver's LED indicator will flash and then turn off.
  4. Toggle mode is now successfully set for that button.

7.4 Setting Latching Mode (Interlock)

Note: For Latching mode, you need to program two different buttons on the remote control: one for ON and one for OFF.

  1. Press the learning button on the receiver module three times.
  2. Wait for the LED on the receiver to light up, indicating it has entered the setting state.
  3. Press the first button on the remote control (e.g., button A) once. The LED will flash 5 times. This button will be for ON.
  4. Press the second button on the remote control (e.g., button B) once. The LED will flash 5 times. This button will be for OFF.
  5. The receiver's LED indicator will then turn off. Latching mode is now successfully set.

8. Troubleshooting

ProblemPossible CauseSolution
Remote control not working / Short rangeLow battery in remote; Interference from other devices; Obstructions (e.g., metal surfaces).Replace remote battery. Relocate receiver away from interference sources. Ensure clear line of sight if possible.
Receiver not responding to remoteRemote not paired; Incorrect working mode set; Power issue with receiver.Ensure remote is paired correctly (see Section 7). Verify the working mode is set as desired. Check power connections to the receiver.
Relay not switchingIncorrect wiring; Overload on relay; Faulty relay.Check wiring against diagrams (Section 5.2). Ensure connected load does not exceed 10A. If problem persists, the relay might be faulty.

9. Maintenance

  • Keep the receiver module and remote control dry and clean.
  • Avoid exposing the devices to extreme temperatures or humidity.
  • Regularly check the remote control battery and replace it when necessary.
  • Ensure all wiring connections are secure and free from corrosion.

10. User Tips

  • This universal remote control system is highly versatile and can be used for a wide range of applications, including controlling lights, electric doors, automated curtains, and various other switches.
  • Experiment with the different working modes (Momentary, Toggle, Latching) to find the best fit for your specific application.
  • When programming Latching mode, remember to assign separate buttons for the ON and OFF functions for proper operation.

11. Warranty and Support

For technical support, warranty information, or further services, please visit the official QIACHIP website at www.qiachip.com.

Please note that this product is designed to work optimally with QIACHIP brand remote controls and receivers. Compatibility with other brands is not guaranteed.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.