DEKO DNS-550E, DKMZ350, MZ239, MZ224, MZ236, MZ240, MZ232, MZ225

Contents

DEKO Auto-Darkening Welding Helmet User Manual

Models: DNS-550E, DKMZ350, MZ239, MZ224, MZ236, MZ240, MZ232, MZ225

1. Introduction

This manual provides instructions for the safe operation, setup, maintenance, and troubleshooting of your DEKO Auto-Darkening Welding Helmet. Please read this manual thoroughly before use and keep it for future reference.

DEKO Auto-Darkening Welding Helmet
DEKO Auto-Darkening Welding Helmet (Example Model)

Safety Precautions

  • Always wear appropriate personal protective equipment (PPE) in addition to the welding helmet.
  • Ensure the helmet is functioning correctly before each use.
  • Do not use the helmet if any part is damaged.
  • Protect the auto-darkening filter from scratches and impacts.
  • Avoid direct exposure to welding arc without proper eye protection.

2. Setup and Adjustment

2.1 Headband Adjustment

The helmet features an adjustable headband designed for comfort and stability. Proper adjustment is crucial for reducing fatigue during prolonged use.

  1. Adjustable Headband Length: Use the top strap to adjust the length of the headband to fit the top of your head.
  2. Adjustable Headband Tightness: Rotate the knob at the back of the headband to adjust the overall tightness around your head.
  3. Headband Fixed Knob: Ensure the side knobs are securely tightened to fix the helmet's position relative to your face.
Adjustable headband for welding helmet
Adjustable headband components for a personalized fit.

2.2 Power Supply and Battery Check

The helmet is powered by a combination of a Lithium Battery and Solar Cells, designed for over 5000 welding hours. The battery type is CR2032.

  • Before first use, ensure the CR2032 battery is correctly installed.
  • The solar cells continuously charge the internal battery during operation in sufficient light.
  • If the helmet fails to auto-darken, check the battery level and replace if necessary.

3. Operating Instructions

The DEKO Auto-Darkening Welding Helmet is designed for various welding processes, including MMA, MIG, MAG/CO2, TIG, Arc Welding, Plasma Welding, Arc Gouging, and Plasma Cutting.

3.1 Auto-Darkening Filter (ADF) Controls

The Auto-Darkening Filter (ADF) automatically adjusts the shade level to protect your eyes from intense light during welding. The controls are typically located on the side or inside the helmet's viewing cartridge.

ADF-550E Auto-Darkening Filter controls
ADF-550E control panel with Delay, Shade, and Sensitivity adjustments.
  • SHADE: Adjusts the darkness level of the filter. The helmet offers a variable shade range of DIN 4 to DIN 9-13. Select the appropriate shade for your welding process.
  • SENS (Sensitivity): Controls how sensitive the filter is to the welding arc. Adjust between low and high settings based on ambient light and welding conditions. A higher sensitivity means the filter will darken with less intense light.
  • DELAY: Sets the time it takes for the filter to return to its light state (DIN 4) after the arc stops. Adjustable from 0.1s to 1.0s. A longer delay is useful for high amperage welding to prevent eye strain from afterglow.

3.2 Eye Protection

The helmet provides ultimate eye protection with UV/IR protection up to DIN 16. The auto-darkening filter switches from light to dark in approximately 1/15000 seconds. In the event of electric failure, the filter remains protecting against UV and IR radiation at a permanent shade 16. This meets ANSIZ87.1-2010 and EN3794/9-13 standards.

Welding helmet providing eye protection
The helmet ensures comprehensive eye protection during welding operations.

3.3 Product Demonstration Video

Official product demonstration showcasing the helmet's features and use.

4. Maintenance

Proper maintenance ensures the longevity and optimal performance of your welding helmet.

  • Cleaning: Regularly clean the helmet shell with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Lens Care: Clean the auto-darkening filter and protective lenses with a soft, lint-free cloth. Use a mild lens cleaning solution if necessary. Avoid scratching the lens surface.
  • Battery Replacement: The helmet uses a CR2032 battery. If the auto-darkening function becomes unreliable or stops working, replace the battery. Refer to the battery compartment for instructions on replacement.
  • Protective Lenses: The outer and inner protective lenses are consumable parts and should be replaced when scratched, pitted, or damaged to maintain clear vision and protection.
  • Storage: Store the helmet in a dry, clean environment away from direct sunlight and extreme temperatures.

5. Troubleshooting

If you encounter issues with your DEKO welding helmet, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Lens does not darken when welding arc starts.
  • Low battery.
  • Sensitivity setting too low.
  • Sensors are blocked or dirty.
  • Ambient light too low for solar cells.
  • Replace CR2032 battery.
  • Increase sensitivity setting.
  • Clean sensors on the ADF.
  • Ensure adequate lighting for solar charging.
Poor visibility through the lens.
  • Protective lenses are dirty or scratched.
  • Incorrect shade setting.
  • Clean or replace protective lenses.
  • Adjust shade setting to appropriate level for welding process.
Helmet feels uncomfortable or unstable.
  • Headband not properly adjusted.
  • Adjust headband length and tightness using the knobs and straps.

6. Specifications

The following table outlines the general specifications for the DEKO Auto-Darkening Welding Helmet (DNS-550E model shown as example; specifications may vary slightly by model).

DNS-550E Welding Helmet Specifications
Detailed specifications for the DNS-550E model.
FeatureSpecification
Model NumberDNS-550E (Other models: DKMZ350, MZ239, MZ224, MZ236, MZ240, MZ232, MZ225)
View AreaDNS-550E: 95*35mm; DKMZ350: 90*35mm; MZ239: 90*30mm; MZ224: 92.5*42.5mm; DNS-980E: 98*80mm
Switch Time (Light to Dark)Adjustable: 0.1s ~ 1.0s; Darkening Speed: 1/25000s (DNS-550E), 1/15000s (DKMZ350), 1/5000s (MZ239), 1/10000s (DNS-980E)
SensitivityAdjustable: low/high (0.00004 seconds)
Shade RangeDIN 4 (Light State), Variable 9-13 (Dark State)
UV/IR ProtectionDIN 16 (Permanent Protection)
Power SupplyLithium Battery + Solar Cells (>5000 welding hours)
Battery TypeCR2032
Helmet MaterialPP
Cartridge SizeApprox. 11.8 x 8.7 x 8.5 inches (general), 12 x 9 x 8.8 inches (DNS-550E)
Visor TypeAuto-Darkening Filter
Recommended IndustryHeavy Infrastructure
User TypeProfessional and DIY Household
Welding FeaturesTraditional Headgear
CertificationCE
Optical Class1/2/1/2
Arc Sensor2
OriginMainland China

7. Warranty and Support

DEKO offers a one-year warranty for this product. Additionally, DEKO provides free lifetime technical support.

DEKO Quality Service banner with warranty information
DEKO Quality Service highlights warranty and technical support.

For warranty claims or technical assistance, please contact DEKO customer support through your purchase platform or the official DEKO website.

8. User Tips

  • Spare Parts: It is recommended to keep spare outer and inner protective lenses on hand, as they are consumable and may need frequent replacement due to scratches or damage. Some users have noted difficulty finding replacements, so consider purchasing spares when available.
  • Dioptric Lenses: If you require dioptric correction, check with DEKO support or your supplier for compatible dioptric glass inserts.
  • Arc Welding: This helmet is suitable for arc welding processes. Ensure proper shade and sensitivity settings for optimal protection.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.