MESTEK IR02C

Contents

MESTEK Digital Infrared Thermometer User Manual

Models: IR02C, IR03A, IR03B, IR01B, IR01C, IR01D

1. Product Overview

The MESTEK Digital Infrared Thermometer is a high-precision, non-contact temperature measurement device designed for various industrial and home applications. It features a color screen backlight, 12-point infrared accurate positioning, adjustable emissivity, and quick measurement capabilities. Certain models also include ambient temperature, humidity, and temperature probe functions.

Mestek IR02C Infrared Thermometer with laser targeting and temperature probe

Figure 1: MESTEK IR02C Infrared Thermometer with laser targeting and temperature probe, showing temperature range -50°C to 800°C (-58°F to 1472°F).

Video 1: Unboxing and initial demonstration of the MESTEK Infrared Thermometer.

2. Setup

2.1 Battery Installation

The thermometer requires 2 AAA batteries (not included). Open the battery compartment located on the handle, insert the batteries according to the polarity markings, and close the compartment securely.

2.2 Initial Use

After installing batteries, press the trigger to power on the device. The color screen backlight will activate, displaying current readings. If the ambient temperature changes significantly, allow the device to stabilize for 30 minutes before use to ensure accuracy.

Mestek IR02C Color Screen Backlight display

Figure 2: The thermometer's color screen backlight display.

3. Operating Instructions

3.1 Basic Measurement

Point the thermometer at the target object and press the trigger. The laser pointer(s) will indicate the measurement area. The temperature reading will be displayed on the screen within 0.5 seconds. The device uses a 12:1 distance-to-spot ratio (D:S), meaning for every 12 units of distance from the object, the measurement spot diameter is 1 unit. For example, at 120 cm distance, the spot diameter is 10 cm.

Mestek IR02C 12-point laser positioning

Figure 3: Illustration of 12-point laser positioning for accurate targeting.

Mestek IR02C Object Distance Ratio 12:1 diagram

Figure 4: Diagram explaining the 12:1 object distance ratio (D:S).

3.2 Mode Adjustment

In standby mode, press and hold the 'MODE' key for 2 seconds to cancel the laser positioning point. Press and hold again for 2 seconds to display the laser positioning. The 'MODE' button also cycles through various display modes and settings:

  1. Click once: Toggle between Ambient / Surface temperature (for models with ambient temperature sensor).
  2. Press twice: Switch to the temperature probe function (for models with temperature probe).
  3. Press three times: Switch to adjust emissivity.
  4. Press four times: Toggle between Celsius (°C) and Fahrenheit (°F) units.
Mestek IR02C Operation Mode Adjustment Method

Figure 5: Visual guide for operation mode adjustment using the 'MODE' button.

Mestek IR02C Celsius Fahrenheit unit conversion

Figure 6: Illustration of Celsius/Fahrenheit unit conversion.

3.3 Emissivity Adjustment

Emissivity (ε) is adjustable from 0.1 to 1.0. The default setting is 0.95. Adjusting emissivity according to the material being measured ensures more accurate readings. Refer to the Emissivity Comparison Table below for common materials.

Mestek IR02C Emissivity Comparison Table

Figure 7: Emissivity Comparison Table for various materials.

3.4 High/Low Temperature Alarm

The device supports setting high and low temperature alarms. When the measured temperature exceeds the set limits, an alarm will sound or be indicated on the display.

Mestek IR02C High/Low Temperature Alarm display

Figure 8: Display showing high and low temperature alarm indicators.

3.5 Maximum Measurement (MAX)

The default measurement value at startup is the maximum value. Continuous measurement can lock a higher temperature point. This feature is useful for identifying hot spots.

Mestek IR02C Maximum Measurement feature

Figure 9: Display indicating the maximum measurement feature.

4. Maintenance

4.1 Cleaning

  • Use a soft, damp cloth to clean the exterior of the device.
  • Do not use abrasive cleaners or solvents.
  • Keep the lens and laser aperture clean and free from dust or debris to ensure accurate readings.

4.2 Storage

When not in use, store the thermometer in a dry place, away from direct sunlight and extreme temperatures. The recommended storage temperature is -10°C to 60°C.

4.3 Battery Replacement

Replace batteries when the low power prompt appears on the screen to ensure continuous operation and accuracy.

5. Troubleshooting

5.1 Common Issues and Solutions

  • Inaccurate Readings:
    • Check and adjust the emissivity setting for the material being measured.
    • Ensure the lens and laser aperture are clean.
    • Allow the device to stabilize for 30 minutes if there's a significant change in ambient temperature.
    • Ensure the target object fills the measurement spot, especially at longer distances.
  • No Display/Device Not Turning On:
    • Check battery installation and ensure correct polarity.
    • Replace with new AAA batteries.
  • Laser Not Visible:
    • Ensure the laser positioning is enabled via the 'MODE' button (refer to Section 3.2).
    • Check battery level.

5.2 Important Precautions

  • Do not measure through transparent surfaces such as glass or plastic.
  • Do not aim the laser at the eyes or indirectly aim at the eyes through reflective surfaces.

6. Specifications

Mestek Infrared Thermometer Model Comparison Table

Figure 10: Detailed specifications for various MESTEK Infrared Thermometer models.

6.1 General Specifications

Feature Specification
D:S Ratio 12:1
Emissivity 0.1~1.0 adjustable
Response Spectrum 8~14um
Laser Less than 1mW/630-670nm, Level 2
Response Time Less than 0.5s
Automatic Shutdown 30 seconds
Data Retention Yes
Operating Temperature 0~40°C
Storage Temperature -10~60°C
Power Supply 1.5V*2 AAA battery (not included)
Accuracy ±2°C
Certification CE, RoHS

6.2 Model-Specific Temperature Ranges

  • IR03A: -50~400°C
  • IR03B: -50~600°C
  • IR01B: -50~550°C
  • IR01C: -50~550°C (includes ambient temperature and humidity)
  • IR01D: -50~800°C (includes ambient temperature and humidity)
  • IR02C: -50~800°C (includes ambient temperature, humidity, and temperature probe measure)
Mestek IR02C Product Dimensions

Figure 11: Product dimensions for the MESTEK IR02C model.

7. Warranty and Support

For warranty information and technical support, please contact MESTEK Official Store directly. Details can typically be found on the product packaging or the seller's official store page.

MESTEK Official Store has been operating since January 23, 2018, with a positive feedback rate of 93.8% and a store rating of 4.8 out of 5.

8. User Tips

  • Model Differences: Be aware that different models (e.g., IR03A, IR02C) have varying temperature ranges and features like ambient temperature/humidity measurement or a temperature probe. Always check your specific model's capabilities against the specifications table.
  • Optimal Measurement: For best results, ensure the target object is within the recommended distance-to-spot ratio (12:1) and that the emissivity setting matches the material you are measuring.
  • Environmental Stability: If moving the thermometer between environments with large temperature differences, allow it to acclimate for about 30 minutes before taking critical measurements.

© 2023 MESTEK. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.