Estardyn XH-A105

Contents

XH-A105 Bluetooth 5.0 Digital Amplifier Board User Manual

Model: XH-A105

Introduction

The XH-A105 is a high-fidelity, two-channel stereo digital power amplifier board featuring Bluetooth 5.0 connectivity. It supports multiple audio input methods including Bluetooth, TF card, and a 3.5mm AUX line input, allowing direct connection to devices like mobile phones and MP3 players. The board includes an onboard volume adjustment potentiometer for convenient control.

Top-down view of the XH-A105 Bluetooth 5.0 digital amplifier board, showing components like the heatsink, capacitors, Bluetooth antenna, TF card slot, AUX input, and volume potentiometer.

Figure 1: XH-A105 Bluetooth 5.0 Digital Amplifier Board Overview

Specifications

Detailed specifications for the XH-A105 amplifier board are provided below:

  • Product Name: Two-channel Bluetooth 5.0 Power Amplifier Board
  • Product Model: XH-A105
  • Input Voltage: DC 12-30V
  • Input Current: > 3A
  • Output Power: Max 100W per channel (100W*2)
  • Audio Input: Bluetooth, TF Card, AUX (3.5mm)
  • Number of Channels: Two channels (Stereo)
  • Output Impedance: 4-8Ω
  • Dimensions: 92mm x 85mm x 18mm (Length x Width x Height)
  • Installation Aperture: 3mm
  • Installation Hole Distance: 85.5mm x 78.5mm
  • Product Weight: Approximately 83g

Power Output Table

The maximum output power varies depending on the input voltage and speaker impedance. Refer to the table below:

Table showing power output (W) for XH-A105 amplifier board at different input voltages (DC12V, DC24V, DC30V) and speaker impedances (4Ω, 6Ω, 8Ω). For DC12V: 36W (4Ω), 24W (6Ω), 18W (8Ω). For DC24V: 96W (4Ω), 72W (6Ω), Not Supported (8Ω). For DC30V: Not Supported (4Ω), Not Supported (6Ω), 112W (8Ω).

Figure 2: Voltage, Resistance, and Power Output Specifications

Note: Ensure that the connected speaker impedance and input voltage are within the supported ranges to prevent damage to the amplifier board.

Setup Instructions

Follow these steps to correctly connect your XH-A105 amplifier board:

Wiring diagram for the XH-A105 amplifier board. Shows connections for DC12-30V power supply to VCC and GND, AUX audio input from an MP3 player, and left/right speakers to -OUTL+ and -OUTR+ terminals. Also indicates power light, Bluetooth light, TF card slot, and volume potentiometer.

Figure 3: XH-A105 Wiring Diagram

  1. Power Supply Connection: Connect a DC 12-30V power supply to the VCC (positive) and GND (negative) terminals on the board. Ensure the power supply can provide more than 3A current. Upon successful power-on, the red power indicator light will illuminate, and the blue Bluetooth indicator light will flash.
  2. Speaker Connection: Connect your speakers to the output terminals.
    • For the left channel, connect the speaker to the -OUTL+ terminals, observing polarity.
    • For the right channel, connect the speaker to the -OUTR+ terminals, observing polarity.
    • Ensure speaker impedance is between 4-8Ω.
  3. Audio Input Connection: Choose one of the following audio input methods:
    • Bluetooth: The board will automatically enter Bluetooth pairing mode when powered on. Search for "XH-A105" on your device and connect. The blue Bluetooth indicator will stop flashing once connected.
    • TF Card: Insert a TF card containing audio files into the TF card slot.
    • AUX Input: Connect an audio source (e.g., MP3 player, mobile phone) to the 3.5mm AUX input jack using an audio cable.

Operating Instructions

Volume Control

  • Onboard Potentiometer: Rotate the green potentiometer knob clockwise to increase the volume and counter-clockwise to decrease it.
  • External Volume Control (for Bluetooth/TF card input): If using Bluetooth or TF card input, you can connect external wires to the "+ VOL -" holes for volume adjustment:
    • Connect "+" and "VOL" to increase volume.
    • Connect "-" and "VOL" to decrease volume.

Audio Input Selection

The amplifier board automatically selects the last active audio input. For example, if you are using Bluetooth audio input and then connect an AUX cable, the board will automatically switch to the AUX input.

Bluetooth Indicator Behavior

  • Rapid Flashing: Bluetooth is not connected and is in pairing mode.
  • Solid Blue: Bluetooth connection is successful.
  • Slow Flashing: Bluetooth is connected and playing audio.

Maintenance

  • Keep the amplifier board clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the board to moisture, extreme temperatures, or direct sunlight.
  • Ensure adequate ventilation around the heatsink to prevent overheating, especially during prolonged use at high volumes.
  • Do not attempt to modify the circuit board, as this may void any implied warranty and could cause damage.

Troubleshooting

Problem Possible Cause Solution
No power indicator light No power supply, incorrect voltage, or loose connection. Check power supply (DC 12-30V, >3A). Ensure VCC and GND are correctly connected.
No sound output Incorrect speaker wiring, wrong audio input selected, or source device issue. Verify speaker polarity and connection. Check audio input selection (Bluetooth, TF, AUX). Test audio source device.
Bluetooth not connecting Board not in pairing mode, or device too far. Ensure no other audio input is active. Keep device close to the board. Restart Bluetooth on your device and the amplifier.
Distorted sound Input volume too high, speaker impedance mismatch, or insufficient power. Reduce input volume. Check speaker impedance against specifications. Ensure power supply meets current requirements.

User Tips

  • Power Supply: For optimal performance and to achieve the advertised 100W per channel, use a robust power supply within the DC 12-30V range, ensuring it can deliver sufficient current (e.g., 5A or more for higher power output). A common user question is about the amplifier's power, and using an adequate power supply is key to realizing its potential.
  • Speaker Matching: Pay close attention to the speaker impedance (4-8Ω) and the power output table in the specifications section to avoid damaging the board or speakers.
  • Heat Management: While the board has a heatsink, consider additional cooling if operating at high volumes for extended periods, especially in enclosed spaces.
  • Audio Source Quality: The quality of your audio output will be influenced by the quality of your audio input source. Use high-quality audio files and cables for the best experience.
XH-A105 amplifier board connected to a stack of two large speakers, demonstrating a typical setup.

Figure 4: Example of XH-A105 connected to speakers

Warranty and Support

This product is designed for hobbyist and DIY audio projects. For technical support or inquiries, please refer to the seller's contact information or online resources where the product was purchased. Keep your purchase records for any potential support needs.

© 2023 Estardyn. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.