Estardyn DC 400W 15A Step-up Boost Converter Module

Contents

Estardyn DC 400W 15A Step-up Boost Converter Instruction Manual

Model: DC 400W 15A Step-up Boost Converter Module

1. Introduction

This manual provides detailed instructions for the Estardyn DC 400W 15A Step-up Boost Converter module. This non-isolated step-up (BOOST) module is designed to convert a lower DC input voltage to a higher, continuously adjustable DC output voltage, while also offering constant current capabilities. It is suitable for a wide range of applications including DIY power supplies, electronic device power, car power supplies, solar panel regulation, battery charging, and driving high-power LED lights.

2. Specifications

FeatureSpecification
Module TypeNon-isolated step-up module (BOOST)
Input VoltageDC 8.5V - 50V
Input Current15A (MAX), enhance heat dissipation if exceeding 8A
Quiescent Current10mA (increases with higher output voltage)
Output Voltage10V - 60V (continuously adjustable)
Constant Current Range0.2A - 12A
Operating Temperature-40°C to +85°C (enhance heat dissipation if ambient temperature is too high)
Operating Frequency150KHz
Conversion EfficiencyUp to 96%
Overcurrent ProtectionYes
Input Reverse Polarity ProtectionNo (ensure correct polarity during connection)
Installation4 x 2.55mm screw holes
Module Dimensions (LxWxH)67mm x 48mm x 28mm
Weight60g

3. Product Overview

The module features clearly marked input and output terminals, along with potentiometers for adjusting output voltage and current. Refer to the diagrams below for component identification.

Top view of the DC 400W 15A Step-up Boost Converter module with labels for Input, Output, Fuse, W502 (Voltage Adjust), and W103 (Current Adjust).
Figure 1: Component identification on the module.
The DC 400W 15A Step-up Boost Converter module held in a hand, illustrating its compact size.
Figure 2: Module size reference.

4. Setup and Wiring

Before connecting, ensure your input power source is within the specified voltage range (DC 8.5V-50V). Pay close attention to polarity as the module does not have input reverse polarity protection.

4.1. Connection Points

  • Input: Connect your DC power source to the 'Input' terminals (IN+ for positive, IN- for negative).
  • Output: Connect your load (e.g., LED, battery, electronic device) to the 'Output' terminals (OUT+ for positive, OUT- for negative).
Diagram showing input and output terminals on the boost converter module.
Figure 3: Input and Output connection terminals.

4.2. Heat Dissipation

For input currents exceeding 8A or when operating in high ambient temperatures, it is crucial to enhance heat dissipation. This may involve adding external cooling fans or ensuring adequate airflow around the module's heatsinks.

5. Operation and Adjustment

The module features two potentiometers for adjusting the output voltage and constant current limit.

Diagram illustrating the location of voltage adjustment (W502) and current adjustment (W103) potentiometers on the module.
Figure 4: Voltage and Current adjustment potentiometers.

5.1. Output Voltage Adjustment (W502)

Use a small screwdriver to turn the potentiometer labeled 'W502' (Voltage adjustment) to set the desired output voltage. Turn clockwise to increase voltage, counter-clockwise to decrease.

5.2. Constant Current Adjustment (W103)

The potentiometer labeled 'W103' (Current adjustment) controls the constant current limit. To set the current limit:

  1. First, adjust the output voltage to your desired level.
  2. Connect an ammeter in series with your load, or use a suitable dummy load.
  3. Turn the W103 potentiometer to set the maximum current your load should draw. Turn clockwise to increase the current limit, counter-clockwise to decrease.
  4. Note: Adjusting the current limit without a load connected can be tricky. It is recommended to adjust with a load or an ammeter to accurately set the limit.

6. Applications

This boost converter module is versatile and can be used in various scenarios:

  • DIY adjustable power supplies (e.g., 12V input to 12-50V adjustable output).
  • Powering electronic devices requiring specific voltage settings.
  • Car power supply for laptops, PDAs, or other digital products.
  • Creating mobile power solutions with high-capacity lithium battery packs.
  • Solar panel voltage regulation.
  • Charging various types of batteries, including rechargeable lithium batteries.
  • Driving high-power LED lights.

7. Maintenance

  • Keep the module clean and free from dust and debris.
  • Ensure proper ventilation, especially during high-power operation, to prevent overheating.
  • Regularly check connections for tightness and signs of corrosion.
  • Avoid exposing the module to moisture or extreme temperatures outside its operating range.

8. Troubleshooting

  • No Output Voltage: Check input power supply, ensure correct polarity, and verify connections.
  • Output Voltage Not Adjustable: Ensure the input voltage is within the specified range and that the potentiometer W502 is functioning correctly.
  • Current Limit Not Working/Inaccurate: Ensure the W103 potentiometer is adjusted correctly, preferably with a load or ammeter. Some users have reported challenges with current limiting; double-check your adjustment procedure and measurement setup.
  • Overheating: Reduce load, ensure adequate heat dissipation (as mentioned in Section 4.2), or check for short circuits in the load.

9. User Tips

  • This module is effective for constant current applications, such as driving LEDs.
  • When setting the current limit, it is best to do so with a load connected to accurately gauge the output current.
  • The module can be successfully connected to lithium battery packs for portable power solutions.

10. Warranty and Support

For any technical assistance or inquiries regarding the product, please contact the seller or manufacturer directly. Keep your purchase records for warranty claims, if applicable.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.