1. Introduction
The ESP32-Audio-Kit is a compact audio development board designed by Ai-Thinker, built around the ESP32-A1S module. It features various audio peripherals, including a TF card slot, headphone output, two microphone inputs, and two speaker outputs, facilitating rapid development for audio applications.
This board supports a wide range of audio formats such as MP3, AAC, FLAC, WAV, OGG, OPUS, AMR, TS, EQ, Downmixer, Sonic, and ALC. It can play music from diverse sources including HTTP, HLS (HTTP Live Streaming), SPIFFS, SDCARD, A2DP source, A2DP receiver, and HFP. The kit also integrates media services like DLNA, VoIP, and network broadcasts, with support for online and offline voice recognition, and integration with services like Alexa and DuerOS.
Note on Module Versions: There are two versions of the ESP32-A1S module: one with a built-in AC101 audio core and another with an ES8388 audio chip. Due to chip availability, the AC101 version (V1.3) has been phased out and replaced by the ES8388 version (V2.3). While the module interface of V2.3 remains largely compatible with V1.3, there are specific differences in audio output pin assignments.
Specifically, the red-boxed part in the pinout diagram for V2.3 (ES8388 version) corresponds to SPORP and SPOLP in V1.3 (AC101 version). The audio output for the V2.3 module is: Right channel output: HPOUTR (positive) and SPORN (negative); Left channel output: HPOUTL (positive) and SPOLN (negative).
Additionally, for the ES8388, the Linein and MIC2 inputs are shared and cannot be used simultaneously. Both MIC1 and MIC2 can function as Linein inputs, with configuration adjusted via software.
2. Safety & Warnings
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
3. Specifications
| Feature | Detail |
|---|---|
| Product Name | ESP32-Audio-Kit ESP32-A1S Audio Development Board |
| Batch/Serial Number | 1005001593671860 |
| Board | Ai-thinker ESP32-Audio-Kit |
| Module | ESP32-A1S V2.2 (batch marking A541) |
| Chip | ESP32 Dual-core LX6, 240 MHz |
| PSRAM | 64 MB (8 MB) integrated |
| Flash | External SPI, 4 MB typical |
| Audio Codec | ES8388 (I2S + I2C control) |
| Dimensions (Module) | 31.5 × 19.0 × 3.1 mm |
| Supply Voltage | 3.0–3.6 V, >500 mA (USB 5V via onboard regulator) |
| Dissipation Power | Low |
| Operating Temperature | Normal |
| Application | Computer |
| Type | Voltage Regulator |
| Package | Module |
| Customization | Yes |
| High-concerned chemical | None |
4. Setup
4.1 Pre-Installation Considerations
Prior to integration, ensure that the operational environment aligns with specified technical parameters. It is recommended to verify compatibility with existing systems to facilitate seamless implementation.
4.2 Installation Process
Follow established procedures for component placement and connection. Proper handling is essential to maintain integrity and prevent potential performance degradation.
4.3 Speaker Amplifier Enable (NS4150)
The PA_ENABLE pin (GPIO21) must be driven HIGH to enable the speaker amplifier (NS4150) for any sound output from the speaker JST jacks. This action should be performed after the ES8388 audio codec has been initialized. The headphone jack (HPOUTL/HPOUTR) bypasses the NS4150 amplifier and does not require this step.
4.4 Visual Overview



5. Operation
During use, maintain conditions within the prescribed ranges for temperature and humidity. Continuous monitoring of performance indicators is advised to sustain operational excellence and ensure stable functionality.
6. Maintenance & Care
Implement routine maintenance protocols to uphold product standards. Periodic inspections are encouraged to ensure ongoing compliance with quality expectations. Store the device in a dry place and keep it away from children.
7. Troubleshooting
7.1 No Sound Output
If flashing firmware (e.g., for Bluetooth operation) results in no sound, verify the DIP switch settings on the board. Ensure that the PA_ENABLE (GPIO21) pin is driven HIGH after the ES8388 audio codec has been initialized. This is crucial for enabling the speaker amplifier. Note that the headphone jack (HPOUTL/HPOUTR) bypasses the NS4150 amplifier and does not require this specific enable signal.
7.2 Firmware Development Issues
When developing firmware, it is strongly advised to avoid manually writing to ES8388 registers. Instead, utilize the espressif/esp_codec_dev library from the ESP-IDF for proper and reliable control of the audio codec.
8. User Tips
For home automation integration, users have reported success flashing Squeezelite firmware. This allows the board to be immediately recognized and functional within Home Assistant setups, providing a straightforward solution for audio streaming.
9. Compliance Information
9.1 CE Marking
This product conforms to the following EU Directives:
- 2014/35/EU (Low Voltage Directive)
- 2014/30/EU (Electromagnetic Compatibility Directive)
9.2 RoHS Declaration
This product is in compliance with Directive 2011/65/EU and its amendment (EU) 2015/863, concerning the restriction of hazardous substances (Pb, Cd, Hg, etc.) in electrical and electronic equipment.
10. Manufacturer & EU Representative Information
10.1 Manufacturer
Company Name: Shenzhen ZhengYi Electronic Technology Co., Ltd
Full Address: Jia An Road XA 41 D3-6F, Bao An District, ShenZhen, Guangdong Province, China
Email: 1020636662@qq.com
10.2 EU Authorized Representative
Company Name: eVatmaster Consulting GmbH
Full Address: Raiffeisen Street2 B11, 63110 Rodgau, Hessen, Germany
Email: contact@evatmaster.com
11. Additional Resources
For more detailed information and advanced configurations, please refer to the official user manual PDF: User Manual (PDF)
12. Warranty & Support
The manufacturer assumes no liability for issues arising from non-compliance with these instructions, improper use, or unauthorized modifications. Product specifications are subject to change without prior notice. For further details, consult the official documentation or contact the support team.