JUNCTEK JDS6600

Contents

JDS6600 DDS Function Signal Generator User Manual

Model: JDS6600 Series | Brand: JUNCTEK

1. Introduction

The JUNCTEK JDS6600 series is a dual-channel DDS (Direct Digital Synthesizer) function signal generator. It integrates multiple functions including Function Signal Generator, Arbitrary Waveform Generator, Pulse Generator, Sweep, Counter, and Frequency Meter. This instrument utilizes advanced DDS technology to deliver stable, precise, pure, and low-distortion signals, making it an ideal testing and measuring tool for electronics engineers, educational laboratories, and research institutions.

The JDS6600 series is available in various models (15MHz, 30MHz, 40MHz, 50MHz, 60MHz), primarily differing in their maximum sine wave output frequency. Its user-friendly interface and robust features make it suitable for a wide range of applications.

2. Safety Information

Please read this manual carefully before operating the instrument to ensure safe and correct usage. Keep this manual for future reference.

  • Ensure the power supply voltage matches the instrument's requirements.
  • Do not operate the instrument in wet or damp conditions.
  • Avoid operating the instrument in explosive atmospheres or in the presence of flammable gases or fumes.
  • Do not attempt to repair or modify the instrument yourself. Refer all servicing to qualified personnel.
  • Disconnect power before cleaning or when the instrument is not in use for extended periods.

3. Package Contents

Upon receiving your JDS6600 series signal generator, please check the package for any damage and verify that all accessories are included:

  • JDS6600 Series DDS Signal Generator (1 unit)
  • Power Adapter (Input: 100~240V~50/60Hz, Output: 5.0V-0.2A) (1 unit)
  • BNC-BNC Cable (1 unit)
  • USB Data Cable (1 unit)
  • BNC-Clip Cable (2 units)
  • Operating Instruction Manual (PDF version) (1 unit)

If any items are missing or damaged, please contact your dealer or the manufacturer immediately.

JDS6600 Signal Generator and included accessories
Figure 3.1: JDS6600 Signal Generator and standard accessories.

4. Product Overview

4.1. Front Panel Layout

Front panel diagram of JDS6600 Signal Generator with labels
Figure 4.1: Front Panel Overview
  • Power Key: Turns the instrument ON/OFF.
  • LCD: 2.4-inch TFT color LCD display for showing parameters and waveforms.
  • Direction Keys: Used for navigation and parameter adjustment.
  • Menu Softkeys: Activate corresponding functions displayed on the LCD.
  • Function Keys: Dedicated buttons for WAVE, MOD, SYS, MEAS, OK, CH1, CH2.
  • Knob: Rotary encoder for continuous parameter adjustment.
  • Channel Control Area: Buttons and indicators for CH1 and CH2.
  • Ext. IN Signal Input Connector: External signal input.
  • CH1/CH2 Signal Output Connectors: BNC connectors for waveform output.

4.2. Rear Panel Layout

Rear panel diagram of JDS6600 Signal Generator with labels
Figure 4.2: Rear Panel Overview
  • TTL Extension Port: For TTL level mode serial interface, supporting secondary development.
  • USB Interface: For PC communication and software control.
  • Power Socket: DC 5V power input.

5. Initial Setup

5.1. Unpacking and Inspection

Before powering on the instrument, carefully unpack it and inspect for any signs of physical damage. Verify that all items listed in the "Package Contents" section are present. If the packaging was damaged during transit, retain it and contact the supplier.

5.2. Power Connection

  1. Connect the provided Power Adapter to the DC 5V power socket on the rear panel of the JDS6600.
  2. Plug the power adapter into a suitable electrical outlet.

5.3. Initial Power On and Language Selection

  1. Press the Power Key on the front panel to turn on the instrument.
  2. The instrument will display a welcome screen, followed by a language selection interface.
  3. Use the soft keys to select your preferred language (e.g., "ENG" for English).
  4. Once selected, the instrument will enter the main operating interface. The language setting will be saved for future power-ons.

6. Operating Instructions

6.1. Main Interface Operation and Waveform Output

  1. Output ON/OFF: Press the OK button to simultaneously turn the output of both channels ON or OFF.
  2. Channel Selection: Use the CH1 or CH2 buttons to select the currently active channel. Pressing the button again will toggle the output of that specific channel ON/OFF. A long press on CH1 or CH2 will set that channel as the main display (upper part of the screen).
  3. Waveform Selection: Press the WAVE key to activate waveform switching for the current channel. When the waveform is active, use the Knob and Direction Keys to quickly switch between arbitrary waveforms and preset waveforms.
  4. Frequency Setting: Press the FREQ soft key to highlight the "Frequency" parameter. Use the Direction Keys to move the cursor to the digit you wish to edit, then turn the Knob to change the value. Long press the FREQ key to change the frequency unit (MHz, KHz, Hz, mHz, uHz).
  5. Amplitude, Offset, and Duty Cycle: Use the corresponding soft keys (AMPL, OFFS, DUTY) to adjust these parameters. Long press these soft keys to reset them to default values.
Video 6.1: Overview of JDS6600 functions including dual-channel waveform, frequency sweep, pulse, burst, and measurement capabilities.

6.2. Measurement Mode (MEAS)

Press the MEAS button to enter the measurement mode interface. This mode allows you to measure various parameters of an input signal.

6.2.1. Measurement Function

The instrument can measure the frequency, period, positive pulse width, negative pulse width, and duty cycle of an input signal. The measurement frequency range is 1Hz-100MHz, and the signal amplitude range is 2mVpp-20Vpp. Input signals are connected via the Ext. IN interface.

  • Coupling Setting: Press the COUP soft key to switch between AC or DC coupling.
  • Gate Time Setting: Use the GATE soft key to set the gate time (0.01S-10S). Use the arrow keys to select the bit and the knob to adjust the value.
  • Measurement Mode Switching: Use the MODE soft key to switch between counting frequency and counting period via the encoder.

6.2.2. Counting Function

The period number of the input signal can be calculated in real-time. After setting all parameters, press the ON soft key to start counting and OFF to stop.

6.3. Modulation Mode (MOD)

Press the MOD button to enter the modulation mode. Use the FUNC soft key to switch between Sweep, Pulse, and Burst functions.

6.3.1. Sweep Function

The sweep function allows you to set a starting and ending frequency within the generator's output frequency range. Sweep time is adjustable from 0.1s to 999.9s. Available sweep types are linear and logarithmic. Sweep directions include forward, reverse, and round trip.

  • Select starting frequency, end frequency, sweep time, sweep direction, and sweep mode using the soft keys.
  • Use arrow keys and the knob to edit parameters.
  • Press ON to start the sweep function and OFF to stop.
Oscilloscope display showing frequency sweep function
Figure 6.1: Frequency Sweep Function Display

6.3.2. Pulse Function

This function allows precise digital adjustment of pulse wave width and period, offering greater accuracy than duty cycle adjustment.

  • Select pulse width, period, offset, and amplitude using the soft keys.
  • Use arrow keys and the knob to edit parameters. Pulse width and period units can be switched between ns and us by pressing the OK key when the item is highlighted.
  • Press ON to start the pulse function and OFF to stop.
Oscilloscope display showing pulse wave output
Figure 6.2: Pulse Wave Output

6.3.3. Bursting Function

The burst function allows the output of a pulse train with 1 to 1,048,575 periods. Burst modes include internal CH2 channel bursts, external input signal bursts, and manual bursts. Ensure the period time of the burst train is less than the burst signal period time.

  • Select the number of pulses and the burst mode using the soft keys.
  • Use arrow keys and the knob to edit parameters.
  • Press ON to start the burst function and OFF to stop.
Oscilloscope display showing burst function output
Figure 6.3: Burst Function Display

6.4. System Settings (SYS)

Press the SYS button to enter the system setting interface. Here you can configure various instrument parameters:

  • Sound Settings: Turn ON/OFF instrument sounds.
  • Brightness Adjustment: Adjust LCD brightness from 0 to 12 levels using the rotary encoder.
  • Language Setting: Select between English and Chinese display.
  • Synchronization: Set CH1 as the operation target for synchronization. CH2 parameters will follow CH1. Select the item to be synchronized (frequency, waveform, amplitude, duty cycle, offset) and confirm.
  • Arbitrary Waveform Number Setting: Adjust the number of arbitrary waveforms for the main interface waveform (1-60).
  • Save/Recall: Save or recall current waveform parameters to/from specified memory locations (00-99).

7. Technical Specifications

ParameterSpecification
Model SeriesJDS6600-15M, JDS6600-30M, JDS6600-40M, JDS6600-50M, JDS6600-60M
Sine Wave Frequency Range0-15MHz (15M model) to 0-60MHz (60M model)
Square Wave Frequency Range0-15MHz (15M model), 0-25MHz (30M, 40M, 50M, 60M models)
Triangle Wave Frequency Range0-15MHz (15M model), 0-25MHz (30M, 40M, 50M, 60M models)
Pulse Width Adjustment100nS~4000S (15M) to 25nS~4000S (60M)
Rise/Fall Time≤25ns (15M) to ≤10ns (40M, 50M, 60M)
Frequency Resolution0.01uHz (0.00000001Hz)
Sampling Rate266MSa/s
Wave Length2048 points/channel
Waveform Vertical Resolution14 bits
Wave TypesSine, Square, Pulse (adjustable duty cycle), Triangular, Partial Sine, CMOS, DC Level, Half Wave, Full Wave, Positive Staircase, Anti-ladder, Noise, Exponential Rise, Exponential Drop, Multisonic, Symplectic, Lorenz, and 60 Arbitrary Waveforms
Frequency Accuracy±20ppm
Frequency Stability±1ppm/3hours
Amplitude RangeFrequency <11MHz: 2mVpp~20Vpp
11MHz ≤ Frequency <31MHz: 2mVpp~10Vpp
31MHz ≤ Frequency: 2mVpp~5Vpp
Amplitude Resolution1mVpp
Amplitude Stability±0.5%/5 hours
Amplitude FlatnessFrequency≤10MHz: ±5%
10MHz<Frequency: ±10%
Offset Range-9.99V~+9.99V
Offset Resolution0.01V
Phase Adjustment Range0°-359.9°
Phase Resolution0.1°
Duty Cycle Adjustment Range0.1%~99.9%
Output Impedance50Ω ±10% (typical)
Frequency Measurement Range1Hz~100MHz
Counting Range0-4294967295
Sweep TypeLinear sweep, logarithmic sweep
Sweep Time0.1s~999.9s
Bursting Number1-1048575
Display2.4 inch TFT color LCD display
Store and Load Memory100 groups (00-99)
Arbitrary Waveform Storage1 to 60 total groups (15 groups by default)
Interface ModeUSB to serial interface
Extension InterfaceTTL level mode serial interface for user secondary development
Communication Speed115200bps
Power SupplyDC5V±0.5V
Operating ConditionsTemperature: 0~40 °C, Humidity: <80%
Diagram showing JDS6600 dimensions: 195mm length, 175mm width, 70mm height
Figure 7.1: JDS6600 Dimensions (approx. 195mm x 175mm x 70mm)

8. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the instrument. Do not use abrasive cleaners or solvents.
  • Storage: Store the instrument in a cool, dry place away from direct sunlight and extreme temperatures.
  • Handling: Handle the instrument with care to avoid physical shock or damage.

9. Troubleshooting

  • Instrument Not Powering On:
    • Check if the power adapter is securely connected to the instrument and the power outlet.
    • Verify that the power outlet is functional.
    • Ensure the power adapter is the correct voltage (DC 5V).
  • No Signal Output:
    • Ensure the output for the selected channel (CH1/CH2) is turned ON (indicated on the display).
    • Check the connection cables (BNC-BNC, BNC-Clip) for proper connection and integrity.
    • Verify that the amplitude and offset settings are appropriate for your measurement device.
  • Incorrect Readings/Malfunction:
    • If the instrument is not working properly or fails performance tests, contact the manufacturer or your dealer for assistance.

10. User Tips

  • PC Software for Arbitrary Waveforms: Utilize the provided PC software to easily draw and generate custom arbitrary waveforms. This greatly expands the instrument's versatility.
  • Secondary Development: The TTL level mode serial interface and communication protocol allow for advanced users to integrate the JDS6600 into custom systems or develop their own control applications.
  • Cable Inclusion: The product package includes necessary cables (BNC-BNC, BNC-Clip, USB) for immediate use and connectivity.

11. Warranty and Support

For any issues, questions, or technical support regarding your JDS6600 series signal generator, please contact JUNCTEK directly:

  • E-mail: junce@junteks.com
  • Website: www.junteks.com

Please have your product model and any relevant details ready when contacting support.

12. Software and Firmware

The JDS6600 supports PC software for enhanced control and arbitrary waveform generation. The communication protocol is also available for secondary development.

Screenshot of PC software control panel for DDS Signal Generator
Figure 12.1: PC Software Control Panel
Screenshot of PC software for arbitrary waveform generation
Figure 12.2: PC Software for Arbitrary Waveform Generation

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.