1. Introduction
The Sinocare ARM-30E+ is an automatic arm blood pressure monitor designed for convenient and accurate measurement of blood pressure and pulse rate at home. This device features a large LCD display, dual user mode with extensive memory, and a comfortable long cuff suitable for various arm sizes. It is intended for general home use and provides essential health monitoring data.
2. Package Contents
Please check the package for the following items:
- Blood Pressure Monitor (ARM-30E+)
- 22-42cm Long Cuff
- User Manual
Note: Batteries and USB cable are not included in the package.
3. Product Features
- Accurate Measurement: Provides reliable blood pressure and pulse readings.
- Dual User Mode: Supports two users, each with 99 memory slots for storing readings.
- Long Cuff Design: Includes a 22-42cm cuff, suitable for a wide range of arm circumferences.
- Cuff Worn Detection: Helps ensure proper cuff placement for accurate readings.
- Irregular Heartbeat Detection: Alerts the user to potential irregular heartbeats.
- One-Button Operation: Simplifies the measurement process for ease of use.
- Automatic Power-Off: The device automatically turns off after 1 minute of inactivity to conserve battery life.
- Data Storage: Yes
- Voice Function: This model does not include a voice function.
- Bluetooth: No
4. Setup
- Power Supply: Insert 4 AAA batteries into the battery compartment. Alternatively, connect the monitor using a micro USB 5-6V adapter (not included).
- Connect the Cuff: Unpack the cuff and securely connect its air tube to the air jack on the side of the blood pressure monitor.
- Positioning: Sit upright in a chair with your feet flat on the floor. Ensure your arm is resting comfortably on a table, with the cuff at heart level.
- Apply the Cuff: Wrap the cuff around your upper arm, ensuring the bottom edge of the cuff is 0.8-1.2 inches (2-3 cm) above your elbow joint. The air tube should run down the center of your arm in line with your middle finger. The cuff should be snug but not too tight.
5. Operation
- Start Measurement: With the cuff correctly applied and you in a relaxed position, press the START/STOP button. The cuff will automatically inflate, and the measurement will begin.
- Reading Results: Once the measurement is complete, your Systolic (SYS), Diastolic (DIA) blood pressure, and Pulse (PUL) rate will be displayed on the LCD screen.
- Memory Function: To view previous readings, press the MEM button. You can cycle through stored measurements for both users.
- User Selection: If using dual user mode, ensure the correct user profile is selected before taking a measurement to store data accurately.
- Power Off: The device will automatically power off after 1 minute of inactivity. You can also manually turn it off by pressing the START/STOP button.
6. Maintenance
- Cleaning: Wipe the monitor and cuff with a soft, dry cloth. Do not use abrasive cleaners or immerse the device in water.
- Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Replacement: Replace all batteries when the low battery indicator appears on the display. Remove batteries if the device will not be used for an extended period.
- Cuff Care: Ensure the cuff is not twisted or sharply bent during storage.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No display/Device won't turn on | Low or dead batteries; Incorrect battery insertion; Power adapter issue. | Replace batteries; Check battery polarity; Ensure USB adapter is 5-6V and properly connected. |
| Error message on display | Improper cuff placement; Movement during measurement; Unstable pulse. | Re-apply cuff correctly; Remain still and silent during measurement; If errors persist due to unstable pulse, consult a healthcare professional or contact support. |
| Inaccurate readings | Incorrect cuff size or placement; Movement; Talking; Recent exercise/stress. | Ensure proper cuff fit and placement; Relax for 5 minutes before measurement; Avoid talking or moving; Take multiple readings and average them. |
| Screen goes blank after connecting USB | Possible internal fault or power issue. | Disconnect USB, remove and reinsert batteries. If issue persists, contact customer support. |
8. Specifications
| Feature | Detail |
|---|---|
| Product Name | Arm Blood Pressure Monitor |
| Model | ARM-30E+ |
| Display | LCD display |
| Measuring Method | Oscillometric measurement |
| Measuring Part | Upper arm |
| Measuring Range | SYS: 57-255 mmHg; DIA: 25-195 mmHg; Pulse rate: 40-199 bpm |
| Accuracy (Cuff Pressure) | ±3 mmHg (±0.4 kPa) |
| Accuracy (Pulse Rate) | ±5% |
| Weight | Approx. 220g (without batteries) |
| Dimensions | 118 * 98 * 62.5 mm |
| Screen Size | 44.5 * 58.5 mm (2.9 inches) |
| Cuff Size | 22-42 cm (8.6-16.5 inches) |
| Batteries Included | No |
| Data Storage | Yes |
| Bluetooth | No |
| Application | Arm |
| Certification | CE |
9. User Tips
- Accuracy: Users report small discrepancies within 1.5-2%, indicating generally accurate readings.
- Battery Life: Batteries can last for a long time, with some users reporting 4 months of daily use (2-3 times a day).
- Cuff Fit: The 22-42cm cuff is versatile and suitable for various arm sizes, including those up to 40cm circumference.
- Power Source: The device can be powered by 4x AAA batteries or a micro USB 5-6V adapter (e.g., a phone charger).
- Sound Function: While this model is stated to be without voice function, if you encounter a version with sound, some users have found that the sound can be disabled by pressing the left key for 5 seconds, then using the left/right keys to select 'SN ON' and changing it to 'SN OFF' with the right key.
10. Warranty and Support
This Sinocare Blood Pressure Monitor comes with a manufacturer's warranty. Please refer to the warranty card included in your package for specific terms and conditions. For any technical assistance, troubleshooting beyond this manual, or warranty claims, please contact the seller or Sinocare customer support directly.
