SUNSHINE LS3 Mini

Contents

Sunshine LS3 Mini 10.5-inch LCD Screen Remover Heating Separator Pad User Manual

Model: LS3 Mini | Brand: SUNSHINE

Introduction

The Sunshine LS3 Mini is a portable LCD screen remover heating separator pad designed for efficient and safe separation of display touch screens on various devices, including iPhones, Samsung phones, and iPads up to 10.5 inches. It features quick and constant temperature heating, intelligent temperature control, and a high-temperature resistant, soft, and non-deformable silicone mat with a safe and non-slip design. This manual provides essential information for the proper setup, operation, and maintenance of your device.

Sunshine LS3 Mini Portable LCD Screen Remover with blue silicone mat

The Sunshine LS3 Mini LCD Screen Remover Heating Separator Pad.

1. Setup

  1. Unpack the Device: Carefully remove the LS3 Mini heating separator pad, power cord, and user manual from the packaging.
  2. Placement: Place the device on a stable, flat, and heat-resistant surface. Ensure there is adequate ventilation around the unit.
  3. Power Connection: Connect the provided power cord to the LS3 Mini and then to a suitable power outlet. The device supports both 110V and 220V, depending on the specific model purchased. Verify your local voltage matches the device's requirements.
  4. Initial Inspection: Before first use, inspect the silicone mat for any signs of damage. The double-layer silicone is designed to be soft, non-deformable, and high-temperature resistant.
Sunshine LS3 Mini packaging showing the device, power cord, and user manual

Package contents: LS3 Mini host, power cord, and user manual.

2. Operating Instructions

2.1 Temperature Control

  1. Power On: Flip the power switch to turn on the device. The LED LCD display will illuminate, showing the actual temperature and preset temperature.
  2. Set Temperature: Press the "SET" button to enter temperature setting mode. Use the "+" (Upward) and "-" (Downward) buttons to adjust the desired temperature within the range of 10-130°C.
  3. Confirm Setting: Once the desired temperature is set, the device will automatically begin heating to reach the preset temperature. The display will show both the actual temperature and the preset temperature.
Close-up of the LS3 Mini control panel showing actual and preset temperature displays, and SET, plus, minus buttons

LED LCD display for intuitive temperature control (10-130°C).

2.2 Screen Separation Process

  1. Pre-heat: Allow the LS3 Mini to reach the desired temperature for screen separation. The rapid heating system ensures efficient and even heat distribution.
  2. Place Device: Carefully place the mobile phone or tablet (up to 10.5 inches) onto the silicone heating mat. Ensure the screen area requiring separation is directly over the heated section.
  3. Heat Application: The constant temperature heating will soften the adhesive holding the screen, making it easier to separate.
  4. Screen Removal: Once the adhesive is sufficiently softened, use appropriate screen opening tools (not included) to carefully pry open and remove the display. Always exercise caution to avoid damaging internal components.
Visual representation of the heating mat with 130°C temperature and heat arrows

Rapid and constant temperature heating for efficient screen separation.

2.3 Product Demonstration Video

Demonstration of the Sunshine LS3 Mini in use for screen separation on various devices.

3. Maintenance

  • Cleaning: Ensure the device is powered off and cooled down before cleaning. Wipe the silicone mat and the main unit with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Storage: Store the LS3 Mini in a dry, cool place away from direct sunlight and excessive dust. The flexible silicone mat can be bent for easy storage.
  • Cable Care: Regularly check the power cord for any signs of damage. Do not use the device if the power cord is frayed or damaged.

4. Troubleshooting

  • Device Not Powering On:
    • Check if the power cord is securely connected to both the device and the power outlet.
    • Ensure the power switch is in the "ON" position.
    • Verify the power outlet is functional.
  • Device Not Heating:
    • Confirm that a temperature has been set using the "SET" button and +/- controls.
    • Allow sufficient time for the device to reach the preset temperature.
  • Inaccurate Temperature Reading:
    • Ensure the device is used in a stable environment, away from drafts or extreme temperatures.
    • If issues persist, contact customer support.

5. Specifications

Table of product specifications for Sunshine LS3 Mini

Detailed product specifications for the Sunshine LS3 Mini.

AttributeValue
BrandSUNSHINE
Product NameLCD Screen Remover
ModelLS3 Mini
Working Size225*140mm
Product Size147*285*34mm
Packaging Size150*115*60mm
Net Weight≈ 447g
Gross Weight≈ 560g
Voltage110V/220V
Frequency60Hz/50Hz
Current1A
Power120W
Temperature Range10-130°C
ConfigurationHost*1, Power cord*1, User manual*1
Diagram showing the dimensions of the Sunshine LS3 Mini

Dimensions of the LS3 Mini, suitable for screens up to 10.5 inches.

6. User Tips

  • Safety First: Always wear appropriate safety gear, such as heat-resistant gloves and eye protection, when operating the heating pad.
  • Gradual Heating: For stubborn adhesives, consider starting with a lower temperature and gradually increasing it to avoid overheating the device or damaging components.
  • Organize Components: The silicone mat features small compartments and grids, which can be used to organize screws and small components during disassembly.

7. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.