DEKO DKRH26H2

Contents

DEKO DKRH26H2 Multifunctional Rotary Hammer Instruction Manual

Model: DKRH26H2

1. Introduction

Thank you for choosing the DEKO DKRH26H2 Multifunctional Rotary Hammer. This powerful tool is designed for various heavy-duty tasks including drilling, hammer drilling, and chiseling in materials such as concrete, masonry, wood, and steel. With its 1000W motor and ergonomic design, it offers efficiency, comfort, and safety for both professional and DIY users. Please read this manual carefully before operation to ensure safe and effective use of your tool.

2. General Safety Instructions

WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

2.1 Work Area Safety

  • Keep work area clean and well lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2.2 Electrical Safety

  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
  • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

2.3 Personal Safety

  • Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
  • Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
  • Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source, picking up or carrying the tool.
  • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
  • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
  • Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

2.4 Power Tool Use and Care

  • Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
  • Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
  • Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
  • Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
  • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
  • Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

3. Package Contents

The DEKO DKRH26H2 Rotary Hammer typically includes the following items:

DEKO DKRH20H3 Rotary Hammer kit with BMC case, side handle, and drill bits
Image: Contents of the DKRH20H3 kit, similar to DKRH26H2. Includes rotary hammer, side handle, drill bits, BMC box, and manual.
  • (1) DEKO DKRH26H2 Rotary Hammer
  • (1) Side Handle
  • (3) Drill Bits (various sizes)
  • (1) BMC (Blow Molded Case) for storage
  • (1) Instruction Manual
  • (2) Chisels (flat and point)

4. Product Overview

Familiarize yourself with the components of your DEKO DKRH26H2 Rotary Hammer:

Diagram of DEKO DKRH26H2 Rotary Hammer with numbered parts
Image: Labeled diagram of the rotary hammer components.
  1. Tool Receptacle (SDS)
  2. Locking Mechanism Cover
  3. Attachable Handle
  4. Changeover Switch (Mode Selector)
  5. Switch Right/Switch Left (Rotation Direction Selector)
  6. ON/OFF Button (Trigger)
  7. Setting Knob (Speed/Impact Regulator)

5. Specifications

Technical specifications for the DEKO DKRH26H2 Rotary Hammer:

Table of specifications for DEKO DKRH26H2 Rotary Hammer
Image: Detailed specifications for the DKRH26H2 model.
FeatureSpecification (DKRH26H2)
Rated input power1000W
Impact rate at nominal rotary speed0-4800 per min
Impact energy per stroke3.2J
No-load speed0-1300 RPM
Spindle collar diameter50mm
Weight (without accessories) approx2.6KG
Protection classII
Length of cable2.0m
Item Size38cm*5cm*20cm

Drilling Capacities:

MaterialMax. Diameter
Masonry (core drill)68mm
Concrete26mm
Wood30mm
Steel13mm

6. Setup

6.1 Attaching the Auxiliary Handle

The auxiliary handle (3) can be swiveled 360 degrees for maximum control and comfort. Loosen the handle, adjust to the desired position, and tighten securely before use.

Image showing the attachable handle of the rotary hammer
Image: The ergonomic, 360-degree swivel auxiliary handle for enhanced grip and control.

6.2 Inserting and Changing Drill Bits (SDS System)

The DEKO DKRH26H2 uses an SDS tool receptacle (1) for quick and secure bit changes.

Close-up of a hand inserting an SDS drill bit into the rotary hammer
Image: Proper insertion of an SDS drill bit into the tool receptacle.
  1. Ensure the tool is unplugged from the power source.
  2. Pull back the locking mechanism cover (2) on the tool receptacle (1).
  3. Insert the SDS drill bit or chisel into the receptacle, pushing firmly until it clicks into place. The SDS system allows for slight movement of the bit once inserted; this is normal and necessary for the hammer action.
  4. Release the locking mechanism cover.
  5. Gently pull on the bit to ensure it is securely locked.
  6. To remove, pull back the locking mechanism cover and pull the bit out.

7. Operating Instructions

7.1 Selecting Operating Mode

The rotary hammer features three function modes, selected using the changeover switch (4):

Close-up of the mode selector switch on the DEKO rotary hammer
Image: The three-function mode selector switch for different work scenarios.
  • Hammer Only (Chiseling-only): For demolition work, chiseling, or breaking concrete.
  • Hammer Drill (Hammering and Rotation): For drilling into concrete and masonry with impact.
  • Drill Only (Rotation only): For drilling into wood, metal, or plastic without impact.

CAUTION: Always ensure the tool is unplugged when changing modes to prevent accidental activation.

7.2 ON/OFF and Speed Control

  • ON/OFF Button (6): Press the trigger to start the tool. Release to stop.
  • Setting Knob (7): This knob allows you to adjust the no-load speed (0-1300 RPM) and impact rate (0-4800 per min) for precise control depending on the material and task. Rotate the knob to increase or decrease the speed/impact.

7.3 Rotation Direction

Use the Switch Right/Switch Left (5) to select the desired rotation direction (forward or reverse). This is typically used for drilling and for removing stuck drill bits.

7.4 Typical Applications

The DEKO DKRH26H2 is suitable for a variety of tasks:

  • Image of a person installing a lamp
    Lamp Installation
  • Image of electrical wire installation in a wall
    Wire Installation
  • Image of air conditioning unit installation
    Air Conditioning Installation
  • Image of a demolished wall
    Demolition Wall
  • Image of water pipe installation
    Water Pipe Installation
  • Image of furniture installation
    Furniture Installation

8. Maintenance

8.1 Cleaning

  • Keep the ventilation openings of the power tool clean to ensure proper cooling.
  • Regularly clean the tool housing with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • Clean the SDS tool receptacle regularly to ensure smooth bit insertion and removal.

8.2 Lubrication

  • The SDS chuck mechanism may require occasional lubrication with specialized grease to maintain smooth operation. Refer to the manufacturer's recommendations for specific lubrication intervals and types.

8.3 Storage

  • Store the power tool and its accessories in the provided BMC case in a dry, secure place out of reach of children.
  • Protect the tool from moisture and direct sunlight.

9. Troubleshooting

ProblemPossible CauseSolution
Tool does not startNo power supply; Faulty power cord/plug; ON/OFF switch malfunction.Check power connection; Inspect cord/plug for damage; Contact service for switch repair.
Tool overheats during useOverloading the tool; Blocked ventilation openings; Prolonged continuous use.Reduce load; Clean ventilation openings; Allow tool to cool down periodically.
Reduced impact or drilling performanceWorn drill bit/chisel; SDS chuck dirty or unlubricated; Internal mechanism issue.Replace worn accessories; Clean and lubricate SDS chuck; Contact service if problem persists.
Smoke appears during operationOverheating due to heavy load or prolonged use; Internal motor issue.Immediately stop operation and unplug the tool. Allow it to cool. If smoke persists, discontinue use and contact service.

10. User Tips

  • For heavy-duty tasks, especially in hot conditions, allow the tool to cool down periodically to prevent overheating and extend its lifespan.
  • The included drill bits and chisels may be suitable for light use, but consider investing in higher quality accessories for more demanding or frequent work.
  • Ensure the chuck is clean and properly lubricated for optimal performance and to prevent bits from getting stuck.
  • When drilling into tough materials, use a steady, firm pressure without forcing the tool. Let the hammer action do the work.

11. Warranty and Support

DEKO offers a one-year limited warranty for this product. Additionally, DEKO provides free lifetime technical support. For warranty claims or technical assistance, please contact DEKO Global Store customer service.

DEKO Quality Service banner with warranty and support information
Image: DEKO Quality Service details, including 1-year warranty and lifetime technical support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.