1. Introduction
This manual provides detailed instructions for assembling and operating your F450 Drone Frame Kit. The F450 is a versatile 4-axis quadcopter frame designed for hobbyists and enthusiasts building their own multi-rotor aircraft. It features a robust design made from nylon and glass fiber, suitable for various flight controllers like MK, KK, FF, and MWC.
Please read this manual thoroughly before assembly and operation to ensure safe and correct usage.
2. Safety Warnings and Compliance
⚠️⚠️ For recreation use only. Illegal modification of drones/planes is prohibited. Please also pay attention to the relevant laws and regulations on the use of drones/planes in your country/area to ensure legal use.
Always operate your drone in a safe environment, away from people, animals, and obstacles. Ensure all components are securely fastened before each flight. Failure to follow safety guidelines may result in injury or damage to property.
3. Package Contents
Verify that all components listed below are present in your package:
- 4x Main Arms (color may vary: white&red, black&red, white&black)
- 2x Center Boards (top and bottom plates)
- 25x M2.5x6 Screws
- 16x M3x8 Screws
- 1x Landing Skid Gear Set (if included in your specific combo, includes 4 pieces and M2.5x8 screws for assembly)


4. Specifications
| Feature | Specification |
|---|---|
| Model Number | F450 |
| Frame Arm Material | Nylon and Glass Fiber |
| Wheelbase | 450mm (17.7 inches) |
| Frame Weight | 282g (with package: 343g) |
| Take-off Weight (Recommended) | 800-1700g |
| Compatible Drone Model | DJI F450 (and similar quadcopters) |
| Compatible Controller Boards | MK, KK, FF, MWC (standard 50mm) |
| Landing Skid Height | 150mm |
| Landing Skid Weight | 72g (for a set of 4) |
| Electrified | No (frame kit only) |
| High-concerned chemical | None |
| Origin | Mainland China |
5. Assembly Instructions
The F450 frame kit requires self-assembly. Follow these steps carefully:
5.1 Frame Assembly
- Attach Arms to Bottom Center Board: Secure the four main arms to the bottom center board using the provided M3x8 screws. Ensure the arms are oriented correctly, with the motor mounts facing outwards. The bottom center board is designed with a PCB for easy wiring of ESCs and power distribution.
- Attach Top Center Board: Place the top center board over the assembled arms and bottom board. Secure it using the remaining M3x8 screws.
- Verify Connections: Double-check that all screws are tightened securely.


5.2 Landing Gear Installation (if applicable)
If your kit includes landing gear, follow these steps:
- Position Landing Gear: Attach each landing gear leg to the underside of the drone arms. The landing gear is universal and can be used with F450, F550, SK480, or S500 frames.
- Secure with Screws: Use the provided M2.5x8 screws (8 pieces for a set of 4 landing gear legs) to firmly attach the landing gear to the frame arms. Refer to the diagrams for correct screw placement.




6. Recommended Configuration (Not Included)
To complete your F450 quadcopter, the following components are recommended:
- Motors: 4x 2212-2216 brushless motors
- ESCs: 4x Electronic Speed Controllers (15~40A)
- Battery: 1x 3S/11.1V/2200-5200MAH LiPo battery
- Propellers: 4x 9443, 1045, or 1047 propellers
- Flight Controller: Compatible with standard 50mm controller boards (e.g., MK, KK, FF, MWC)
7. Operating Guidelines
Once your F450 quadcopter is fully assembled with all electronic components, follow these general operating guidelines:
- Pre-Flight Check: Before each flight, inspect all components for damage, loose connections, or obstructions. Ensure propellers are securely attached and oriented correctly.
- Battery Safety: Use only recommended batteries. Charge batteries in a safe, fire-proof location. Never leave charging batteries unattended.
- Flight Environment: Operate in open areas, away from people, buildings, and power lines. Avoid flying in strong winds or adverse weather conditions.
- Flight Controller Setup: Calibrate your flight controller according to its specific manual. Ensure all sensors (accelerometer, gyroscope, compass) are calibrated correctly.
- First Flight: For your first flight, start with short, low-altitude hovers to test stability and control. Gradually increase flight duration and complexity as you gain experience.
- Emergency Procedures: Familiarize yourself with your flight controller's emergency procedures, such as failsafe settings.
8. Maintenance
Regular maintenance will extend the lifespan of your F450 drone frame kit:
- Inspect Frame: After each crash or hard landing, inspect the frame arms and center boards for cracks or damage. Replace any damaged parts immediately.
- Check Screws: Periodically check all screws for tightness. Vibrations during flight can cause screws to loosen.
- Clean Components: Keep the frame and electronic components clean from dust, dirt, and moisture. Use a soft, dry cloth for cleaning.
- Motor Mounts: Ensure motor mounts are secure and free from excessive vibration.
- Landing Gear: Inspect landing gear for signs of wear or damage, especially after rough landings.
9. Troubleshooting
Here are some common issues and their potential solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Drone unstable/flips on takeoff | Incorrect propeller orientation; improperly calibrated flight controller; loose motor mounts. | Ensure propellers are installed correctly (CW/CCW). Recalibrate flight controller. Tighten motor mount screws. |
| One motor not spinning | Faulty motor or ESC; loose wiring connection. | Check wiring between ESC and motor, and ESC and flight controller. Test motor/ESC individually. Replace if faulty. |
| Short flight time | Underpowered battery; inefficient propellers; heavy payload. | Use a higher capacity battery. Ensure propellers are matched to motors. Reduce payload. |
| Excessive vibration | Unbalanced propellers; loose frame components; bent motor shaft. | Balance propellers. Tighten all frame screws. Inspect motor shafts for bends. |
10. User Tips
- Build Quality: Users have noted the good build quality of the frame, suggesting it's a reliable base for your drone project.
- Component Compatibility: The frame is designed for standard 50mm controller boards, offering flexibility in choosing your flight controller.
- Landing Gear Versatility: The landing gear is compatible with various frames like F450, F550, SK480, and S500, making it a versatile accessory.
11. Warranty and Support
This F450 Drone Frame Kit is manufactured to high standards. For any issues or support inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.
Please note that this product is a frame kit and does not include electronic components. Warranty typically covers manufacturing defects of the frame components only.