1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your BYNCG European Car License Plate Frame Reverse Backup Camera. Designed for universal car compatibility, this camera enhances parking safety with its wide viewing angle and night vision capabilities. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Safety & Warnings
Read all instructions before use to ensure safety and prevent damage.
2.1. General Safety Precautions
- Personal protection: Always wear appropriate safety protective equipment such as goggles and gloves during operation.
- Stable environment: Ensure that the vehicle is parked on a flat, sturdy, and well-ventilated surface. Use a jack and safety stand for reliable support. Do not rely solely on the jack.
2.2. Product Warnings
- Children: Keep the device and its cord out of reach of children under 3 years old.
- Plastic Bag: To avoid danger of suffocation, keep this plastic bag away from babies and children. Do not use this bag in cribs, beds, carriages, or play pens. This bag is not a toy.
2.3. Professional Advice
This manual provides general guidance. Car maintenance requires professional knowledge, specialized tools, and experience. We strongly recommend that you entrust the installation work to a qualified car maintenance technician. Incorrect installation may cause vehicle malfunctions, performance degradation, or serious safety accidents.
3. Product Features
- High-definition wide viewing angles (170 degrees).
- Good waterproof, shock-proof, and anti-jamming functions (IP67/IP68).
- CMOS imaging sensor for clear images.
- Support NTSC video system.
- Embedded mounting in the license plate frame for a clean installation.
- Snap-in design for easy installation.
- Available with 8LED, 12LED, or IR night vision for low illumination environments (works within 3 meters at night).
- Connects to any monitor with a composite yellow RCA jack.
- Utilizes an original chip for stable quality performance and vivid image colors.
- P&G CCD Lens with six layers of high-definition glass for clearer effects, longer life, and resistance to aging, heat, and cold.
4. Specifications
| Attribute | Value |
|---|---|
| Item Type | Registration Plate Holder / Rear View Camera |
| Material | ABS |
| Model Name | EU |
| Resolution | 520TVL (TV Lines) |
| Working Voltage | 12V |
| Waterproof Level | IP67 (Professional IP68 mentioned in image) |
| Night Vision | Yes |
| LED Quantity | 8pcs or 12pcs (depending on model) |
| White Balance | Auto |
| Car Model Compatibility | Universal for the car (Covers 95% of car models) |
| Item Length | 55cm (545mm) |
| Item Width | 14cm (140mm) |
| Item Height | 7cm (30mm) |
| Item Weight | 400kg (This seems to be a typo in source data, likely 0.4kg or 400g) |
| Package Weight | 0.647kg (1.43lb.) |
| External Testing Certification | CE |
| Origin | Mainland China |
5. Setup & Installation
5.1. Preparation Before Installation
- Tools and Materials: Ensure that the vehicle's user manual, service manual, necessary specialized tools (e.g., torque wrenches), and general-purpose tools are readily available.
- Accessory Check: After unpacking, immediately check against the accessory list to ensure all parts are present and undamaged. The package includes:
- 1x Rear View Camera (integrated into license plate frame)
- 1x Power Cable (1m)
- 1x Video Cable (6m)
- Old Parts Comparison: Carefully compare the new parts with the removed old parts, and confirm that key features such as size, shape, interface, and bolt hole position are consistent before installation.
5.2. Safety Preparation
- Park the vehicle, apply the handbrake, and secure the non-operating wheels with chocks.
- Disconnect the negative cable of the battery (negative first, then positive) and properly isolate it.
5.3. Disassembly of Old Accessories (if applicable)
- Orderly Disassembly: Disassemble from the outside to the inside and from accessories to the main body. Properly store and label all bolts, nuts, clips, and small parts.
- Avoid Violence: Use appropriate tools. If there is any jamming, check for hidden fixing points or buckles. Do not pry or pull forcibly.
- Handling Connections: For electrical connectors, first press down the latch and then pull it out. For oil pipelines, first clean the area around the connection and use a special tool to disassemble it, preparing a container to catch the flowing oil.
- Clean Contact Surface: After removing old parts, clean the installation contact surface to ensure it is free of rust, oil stains, and residues of old sealing materials.
5.4. Installation of New Accessories
- Replacement of Consumables: Damaged gaskets, sealing rings, O-rings, clamps, locknuts, etc., must be replaced with new ones.
- Standardized Tightening: Use a torque wrench to tighten bolts according to the sequence and torque values specified in the maintenance manual.
- Reliable Connection: Ensure all electrical plugs are fully inserted and locked. All oil and air pipes must be securely connected with clamps in the correct position.
- Add Lubricant/Sealant: Apply the specified type of lubricating grease or sealant to designated locations (e.g., bearings, threads, sealing surfaces) as required by the manual.
5.5. Wiring Diagram
The camera system requires connection to your vehicle's power supply and monitor. The red trigger wire from the 6-meter video cable needs to be connected to the reverse lights' 12V+ power and the radio's trigger wire.
6. Operating Instructions
Once correctly installed and wired, the camera system operates automatically:
- When the vehicle is put into reverse gear, the camera will automatically activate and display the rear view on your connected monitor.
- The integrated LEDs (8LED, 12LED, or IR) provide night vision capabilities, enhancing visibility in low-light conditions.
- The wide-angle lens provides a comprehensive view of the area behind your vehicle, reducing blind spots during reversing.
7. Maintenance & Storage
7.1. Break-in Period
Some components may require a break-in period to achieve optimal performance. Avoid aggressive driving during the initial stage after installation.
7.2. Regular Inspection
It is recommended that during the first maintenance after installation, a technician should review your installation work to ensure everything is secure and functioning correctly.
7.3. Cleaning
Regularly clean the camera lens and the license plate frame to ensure an unobstructed view and proper functioning of the LEDs. Use a soft, damp cloth and avoid abrasive cleaners.
8. Troubleshooting
8.1. Post-Installation Inspection and Testing
- Visual and Manual Inspection: Confirm that all components are installed in place, and no tools or parts are left in the engine compartment or work area.
- Phased Testing (Crucial):
- Static Test (not started): Restore the battery connection. Turn on the power, check the dashboard for any fault lights, and test relevant electrical functions (e.g., lights, switches).
- Idle Test (after startup): Start the engine and observe for any abnormal noise, vibration, oil leakage, water leakage, or air leakage. Check the instrument panel data for normal operation.
- Dynamic Road Test (conducted cautiously): Conduct low-speed tests on a closed road section that is absolutely safe and legal. First, test basic functions such as braking and steering to feel whether the vehicle is functioning normally. Gradually test the functions of systems related to newly replaced parts.
8.2. Fault Symptoms
If abnormal noise occurs, warning lights illuminate, fluid leaks, unusual odors, or performance decreases after installation, immediately stop using the vehicle and contact a professional technician for troubleshooting.
9. User Tips
- Universal Fit: This license plate frame camera is designed to be universal and can fit most car models. The license plate itself is mounted over the frame.
- Night Vision Performance: The camera offers high-definition night vision, providing clear images even in dark environments.
- Cables Included: The product comes with a 1m power cable and a 6m video cable for installation.
- AHD/CVBS Compatibility: If your car's monitor or head unit does not support AHD signal, you can switch the camera to CVBS mode by cutting the designated white wire on the control line.
10. Warranty & Support
For detailed warranty information and further support, please refer to the official user manual PDF provided by the manufacturer. A digital version of the user manual is available at: User Manual (PDF)
10.1. Manufacturer Information
Company Name: Yiwu Yuet top e-commerce limited
Full Address: Room 401, No. 1, Building 7, Zongtang Second District, Jiangdong Street, Yiwu City, Zhejiang Province
Email: 517636919@qq.com
Responsible Person: MoRuChao
Phone: +86-13631860484
10.2. EU Representative Information
Company Name: MJCM SARL
Full Address: 78 avenue des Champ-Elysees Bureau 326 Paris Ile-de-France
Email: mjcm190928@gmail.com
Phone: 0033767213611