EFT 12S 480A

Contents

EFT 12S 480A Large Current Power Distribution Board User Manual

For Four-Axis/Six-Axis Agricultural Power Management Module

1. Product Overview

The EFT 12S 480A Power Distribution Board (PDB) is a high-current power management module designed for multi-rotor aircraft, specifically four-axis and six-axis agricultural drones. It efficiently distributes power from the main battery to multiple Electronic Speed Controllers (ESCs) and other onboard components, ensuring stable and reliable operation.

EFT 12S 480A Power Distribution Board

Figure 1: EFT 12S 480A Power Distribution Board

Video 1: Overview of the EFT Power Distribution Board.

2. Specifications

FeatureSpecification
Brand NameEFT
Model Number12S 480A (V3)
Voltage RatingUp to 12S
Current Rating480A
SizeΦ150mm * 16mm
Weight200g
MaterialComposite Material
ApplicationFour-axis/Six-axis Agricultural Power Management Module, Airplanes, RC Vehicles
Quantity1 pcs
Is ElectricNo battery
Is Batteries IncludedNo
Is it battery/power supplyNo
Is it charger/adapterNo
High-concerned chemicalNone
WheelbaseBottom Plate
Remote Control Peripherals/DevicesDISCHARGER
Upgrade Parts/AccessoriesPDB
RC Parts & AccsPDB
OriginMainland China
Recommend Age14+y
Dimensional drawing of the PDB

Figure 2: Dimensional drawing of the PDB (measurements in mm).

3. Setup and Installation

Follow these steps for proper installation of the EFT 12S 480A PDB:

  1. Step 1: Mount the PDB to the Fuselage
    Secure the PDB (sub-plate) to the bottom of your aircraft's fuselage using nylon screws. Ensure it is firmly attached and correctly oriented (refer to the arrow on the board for forward direction).
    PDB mounted with nylon screws

    Figure 3: PDB mounted to the fuselage using nylon screws.

  2. Step 2: Solder Power and Connect Signal Lines
    Solder the main power transfer power cord with an XT90 male connector. Then, connect the power outputs to your ESCs according to the axis configuration (four-axis or six-axis). Ensure the power transfer signal lines are sequentially inserted into the corresponding ports on the distributor plate. Pay close attention to the installation sequence and polarity.
    PDB with power cords and signal lines connected

    Figure 4: Power cords (XT90 male) soldered and signal lines connected to the PDB.

    PDB interface labels

    Figure 5: Labeled interfaces on the PDB, showing 12S power supply, ESC signal, Main power connector, and 6S power supply interfaces.

  3. Step 3: Mount Flight Control Panel and Connect Signal Lines
    Mount your flight control panel onto the distributor plate, typically using 3M adhesive. Connect the power transfer signal lines sequentially into the flight control unit. Once these connections are made, the physical installation is complete, and you can proceed with flight control parameter adjustments.
    Flight control panel mounted on PDB with signal lines

    Figure 6: Flight control panel mounted on the PDB with signal lines connected.

    PDB installed in drone frame with flight controller

    Figure 7: PDB and flight controller installed within a drone frame, showing integrated wiring.

4. Operating Instructions

Once installed and wired correctly, the PDB operates passively to distribute power. Ensure all connections are secure before applying power to the system. The PDB is designed to handle high currents, providing a stable power supply to all connected components.

  • Power On: Connect the main battery to the XT90 input connector.
  • System Check: Before flight, always perform a thorough system check to ensure all components are receiving power and functioning correctly.
  • Power Off: Disconnect the main battery from the XT90 input connector.

5. Maintenance

Regular maintenance helps ensure the longevity and reliability of your PDB.

  • Visual Inspection: Periodically inspect the PDB for any signs of physical damage, loose connections, or corrosion.
  • Cleaning: Keep the board clean and free from dust, dirt, and moisture. Use a soft, dry brush or compressed air for cleaning. Avoid using liquids.
  • Connection Integrity: Ensure all soldered joints and connectors remain secure. Re-solder or replace any loose or damaged connections.
  • Temperature Monitoring: During operation, ensure the PDB does not overheat. Excessive heat can indicate an overload or a short circuit.

6. Troubleshooting

If you encounter issues with your PDB, consider the following:

  • No Power to Components:
    • Check the main battery connection and ensure it is fully charged.
    • Verify all power cables are correctly soldered and connected to the PDB.
    • Inspect for any blown fuses (if applicable) or damaged traces on the PDB.
  • Intermittent Power:
    • Check for loose connections or cold solder joints.
    • Ensure connectors (e.g., XT90) are not worn out and provide a solid connection.
  • Overheating PDB:
    • Reduce the load on the system if possible.
    • Check for short circuits in any connected components.
    • Ensure adequate airflow around the PDB.

7. User Tips

  • Cable Management: Proper cable management is crucial for preventing shorts and ensuring reliable connections. Use zip ties or cable sleeves to keep wires tidy.
  • Solder Quality: Always use high-quality solder and ensure strong, clean solder joints for all connections to prevent power loss or intermittent issues.
  • Orientation: Pay attention to the arrow indicating the forward direction on the PDB during installation to ensure correct alignment with your flight controller.

8. Warranty and Support

For warranty claims or technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase. This manual provides general guidance; specific issues may require professional assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.