4th Monitor Mount Add On
“
Specifications
- Compatibility: ASR monitor stands
- Material: Aluminum extrusion
- Includes: Monitor mount box, extrusions, corner gussets, angle
brackets, standoffs
Product Usage Instructions
Assembly Guide
- Assemble corner gussets with M8 screws and T-Nuts. Ensure
correct orientation of T-Nuts. - Slide gussets onto 1.5 x 18 extrusion and tighten. Repeat for
both 18 extrusions. - Assemble corner plates with screws and T-Nuts. Slide onto 18
extrusion and tighten. - Prepare corner gussets by removing tabs and attaching T-Nuts
and screws. - Slide T-Nuts and gussets onto 16 extrusion, then slide 10
extrusions through gussets. - Slide assembled 18 extrusion and corner plate through 10
extrusions. Tighten.
Installation Guide
- Place M8 T-Nuts on the monitor stand’s horizontal
extrusion. - Screw the 4th monitor mount using socket screws and the placed
T-Nuts. - Fasten VESA plate to screen using included M4 screws. Use
standoffs if needed for spacing. - Fasten the screen to the stand using M8 x 16 socket screws.
Tighten fully.
FAQ
Q: What tools are required for assembly?
A: 6mm Allen key, Tape Measure. A Philips head screwdriver may
be needed for display screws.
Q: Where can I find support or assistance?
A: Contact our support team at Advanced
Help Center.
Q: How do I install an M8 T-Nut?
A: Insert the T-Nut perpendicular into the desired slot of the
extrusion, then use a small allen key to straighten it through the
hole until it snaps into place.
“`
Advanced 4th monitor mount add-on
ASSEMBLY AND USER GUIDE
Table of Contents
Disclaimer …………………………………………………………………………………………………………………………….. 3 Required Tools……………………………………………………………………………………………………………………..1 Content of package……………………………………………………………………………………………………………..2 Assembly guide…………………………………………………………………………………………………………………….3 Installation guide ………………………………………………………………………………………………………………….7
T-Nut install tip ………………………………………………………………………………………………………………10 User Guide ………………………………………………………………………………………………………………………….11
Disclaimer
This assembly guide shall be considered as such: a guide. The steps, methods and measurements are suggestions from our assembly experience and are in no way shape or form absolute. The dimensions shown throughout the guides are reference dimensions. They are subject to be revised without notice and can be altered for preferred position of your peripherals. If you consider doing a step differently, feel free to try a different method that works for you! On the other hand, any damage caused during assembly is solely your responsibility.
Take your time, loosen some screws if it doesn’t fit, or ask our support team for help before throwing an allen key to the other side of the room. You got this!
Required Tools
6mm Allen key
Tape Measure
*And maybe a Philips head screwdriver, if your display screws are those
For questions, issues or comments, feel free to reach our support team! https://www.advancedsimracing.com/pages/advanced-help-center
1
Content of package
Boxes
1X monitor mount box
1.5″ X 10″ extrusion 2X
1.5″ X 18″ extrusion 2X
1.5″ X 16″ extrusion 1X
VESA plate 1X
Corner Gusset & Cover 8X each
Angle Brackets 2X
1.5″ End Cap 6X Push Pin 6X
M8 T-Nuts 28X
M4 X 16 standoffs
M8 X 16
4X
Hex screws 28X
2
Assembly guide
1. Assemble 4 X corner gussets with 2 M8 screws and 2 M8 T-Nuts. Screw in the T-Nuts no more than a turn.
Make sure to respect the shown orientation of the t-nuts for trouble-free assembly.
2. Slide the gussets on either side of the 1.5″ x 18″ extrusion. Tighten fully. Repeat for both 18″ extrusions.
2X
3. Assemble 2X corner plates with 4X M8 X 16 socket screws and 4X M8 t-nuts each. Tighten no more than a turn.
2X
3
4. Slide the assembled corner plates on the 18″ extrusion as shown. Repeat for both 18″ extrusions. Tighten no more than hand tight and set aside.
2X
5. Prepare 4 corner gussets with the following twist : Using the flathead screwdriver, slide the flathead under the small tab on the bottom, and pry out the tab. It will snap at the base. Snap off both tabs on one side.
6.
Prepare the snapped gussets with
4X
2X M8 T-Nut and 2X M8 X 16 socket
screw each.
4
7. Slide 2X M8 t-nuts to the middle of the 16″ extrusion, followed by the gussets to both ends, broken sides towards the extrusion as shown. Tighten finger tight.
8. Slide the 10″ extrusions through the remaining open part of the gussets. Tighten hand tight.
5
9. Slide the previously assembled 18″ extrusion and corner plate through the 10″ extrusions as shown. Tighten hand tight.
10. Cap up the extrusion ends using the endcaps and push pins.
6
Installation guide
Installation is shown on an ASR single TV monitor stand, steps are the same for all our monitor stands.
1. Place 4X M8 t-nuts on top of the horizontal extrusion of the monitor stand. Use the tip at the page “t-nut install tip” for help!
2. Screw the 4th monitor mount using 4X M8 X 16 socket screws and the previously placed t-nuts.
7
4. Fasten the VESA plate to your screen using your screen’s included M4 screws. If the mount cannot fit flush or causes interference with the display’s cables, use the included standoffs to space out the mount. Do not use the standoffs as screws.
6. Fasten the screen to the stand using 2X M8 x 16 socket screws. Tighten fully.
8
Congrats on your new advanced 4th monitor mount!
9
T-Nut install tip
Insert an M8 T-Nut in the desired slot of the extrusion. Insert the T nut perpendicular, and with the help of a small allen key in your attire such as a 3mm, pry the T nut straight with the allen key through the hole. The t-nut will snap into place when in position. This technique is used throughout our assembly methods and may be used for supplementary accessory
10
User Guide
Your advanced integrated monitor stand is built with easy adjustment in mind. To bridge the gap between the main screen and the upper screen, loosen the 4 M8x16 socket screws on the corner gussets holding the 16″ extrusion and the 2 M8 X 16 socket screws from the corner plate to the vertical extrusion. Go one direction at a time to avoid damage or issues. After all the adjustments, don’t forget to snap in the corner gusset caps for a finished look!
11
To adjust the angle of the screen, loosen a few turns the M8 X 16 screws through the curved slots on the corner plate, and crack loose the screw up top. For a few extra degrees, you can do the same with the vertical section of the corner plate.
12
Documents / Resources
 |
Advanced Sim Racing 4th Monitor Mount Add On [pdf] User Guide 4th Monitor Mount Add On, 4th Monitor Mount Add On, Monitor Mount Add On, Add On, On |