ADAM VISTAR-C01 Nano Smart Tag Card
Specification
- Nano Smart Tag Card
- Model Name: AVISTAR COI
- Battery Capacity: 80mAh / 3.7V / 0.296Wh
- Wireless Input: 2.5W max.
- Bluetooth Version: V5.4
- Speaker Volume: 60 – 90 dB
- Connection Range:
- Indoors: 10 – 20 meters.
- outdoors: 20-50 meters.
- Size: 56.5 x 36 x 5 mm
- 3-Year Limited Warranty
- Weight: 13 g
- Made in China
Product Introduction
LED Indicators Introduction
Charging: Orange light stays on with two beeps.
Fully Charging: Green light stays on.
How to Use
- Power ON: Press the button once. A four-beep sound confirms the device is powered on.
- Power OFF: Quickly press the button twice, then press and hold the third time. Two beeps confirm the device is powered off.
- Reset: Quickly press the button four times, then press and hold the fifth time. Three beeps confirm the reset.
How to Pair
- Turn on Bluetooth on your iPhone.
- Make sure your AVISTAR COI is powered on.
- Open the Apple Find My app.
- In the Items tab, tap Add Item.
- Tap Other Supported Item (your iPhone will begin searching for the AVISTAR COI).
- When the card appears, tap Connect.
- Follow the onscreen instructions to name your card and register it to your Apple ID.
- Confirm that your AVISTAR COI appears in the Items list.
- Do not leave the Apple Find My app while pairing your AVISTAR col.
- If your AVISTAR COI does not appear in Items, remove the item from the app and perform a reset on the card (see “Reset” Settings), then try pairing again.
How to Charge
You can check the battery level by selecting your AVISTAR COI in the Find My app. Charge your AVISTAR COI with a MagSafe, Qi or Qi2-compatible wireless charger.
Unwanted Tracking Notification
- If your AVISTAR COI is separated from your iPhone and detected moving with another person using an Apple device over time, that person will receive a tracking alert.
Safety Warnings
- Do not expose the device to temperatures below 140°F or above 450 (1130°F.)
- Do not expose the device to an open flame, immerse it in water, or expose it to rain, as this will damage the device.
- Always check for damage to the device, cables, or accessories before using the device.
- If damaged, do not use the device.
- Do not attempt to disassemble, modify, puncture, or apply force to the device, as this may cause serious damage and void the warranty.
- Do not expose the device to corrosive liquids or high humidity, as these may seriously damage the device and void the warranty.
Attention
Keep away from children
Do not disassemble, puncture, drop, bend, or modify
3-Year Limited Warranty
Please scan the QR code on the packaging for the user manual
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
CE Declaration of Conformity
EN ADAM elements International Co., Ltd. hereby declares that the product complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: https://www.adamelements.com/eu-conformity
CONTACT
- ADAM elements International Co., Ltd.
- +886-2-2738-9900
- www.adamelements.com
- support@adamelements.com
- FCC ID: 2ABY9AVISTAR-C01
CCAH25LP7490T8
Documents / Resources
 |
ADAM VISTAR-C01 Nano Smart Tag Card [pdf] User Manual 2ABY9VISTAR-C01, 2ABY9VISTARC01, VISTAR-C01 Nano Smart Tag Card, VISTAR-C01, Nano Smart Tag Card, Smart Tag Card, Tag Card, Card |