R210TC Ray-On Single Channel
Column Loudspeaker
User Manual
 |
 |
 |
R210TC Ray-On Single Channel Column Loudspeaker
Identification number : 1438
Active Audio
8 Rue Johannes Gutenberg, 44340 Bouguenais, France
14
1438-CPR-0337
EN 54-24:2008
Type B
Loudspeaker for voice alarm systems for fire detection systems and fire alarm in buildings
RayOn models
Rmini-b, Rmini-w, R70TC-w, R70TC-b, B70TC-b, B70TC-w R110TC-w, R110TC-b, R210TCw, R210TC-b
EU Conformity declaration
We, Active Audio SAS
8 rue Johannes Gutenberg
44340 Bouguenais France
Hereby declare under our own responsibility that the following product:
Type : 70/100V Loudspeaker
Range: Ray-On
Model: R70 TC
ls in conformity with the directive: 2014/35/UE now Voltage”)
In respect of the following norms and standard: EN62368-1 (October 2014)
and .with the directive :2014/30/EU (Equipment EMC)
in respect of the following norms and standard: EN55020/2007+Al2/2016
Bouguenais, 06th of June 2022,
Mr Mathieu POBEDA, Technical Director
General Presentation
R70, R110 and R210 columns exist in 3 versions :
- R70TC, R110TC, R210TC : passive columns working in 8Ω and 70V/100V, with the EN5424 certification
- R70+, R110+, R210+ : active columns with DANTE interface and amplifier
All versions of a each column (for instance R110TC and R110+) same dimensions. For changing the version (for instance from R210TC to R210+), send back the product to the distributor.
The Ray-On column loudspeakers are passive, and based on the DGRC principle. The range includes three column models, and a proximity speaker:
- R70, height 70cm;
- R110, height 1.1m;
- R210, height 2.1m;
- Ray-On Mini, a proximity speaker.
This technical manual is for column speakers R70TC, R110TC and R210TC. A specific technical manual is devoted to the Ray-On Mini, R110 and R110T. Another specific manual is devoted to active versions R70+, R110+ and R210+ and PoE versions (R70PoE, R110PoE and B70PoE).
Using the DGRC principle ensures an optimal sound coverage and intelligibility on the listening zone; it is illustrated in figure 1. For every model, the range depends on the installation height (see section 2).
Ray-On loudspeakers are ideal for speech reinforcement in small to large spaces where the listening zone is horizontal (slope < 5°). Made of aluminum, Ray-On loudspeakers can be installed outdoor. They are suited for airports, railway stations, churches, conference rooms, shopping malls, amusement parks, etc.
Models R70TC, R110TC, and R210TC are compliant with standard EN5424 type B. They can be used in PA systems for safety announcements.
Positioning
The most important parameter for the installation of Ray-On loudspeaker is its mounting height because the range of the column directly depends on it.
Figure 2 on the facing page shows the ±5dB range1 versus to the mounting height, for the direct field2 at mid- frequencies (300Hz-3kHz).
- Range for a standing audience shown. For a seating audience, take off 40cm to the column height.
- Taking the reverberated field into account minimizes the influence of the floor’s material.
- Ears are at 1.15m from floor for a seated audience, 1.55m for a standing audience.
| Mounting height | ||||
| Minimal | Nominal | Maximal | ||
| Ray-On 70TC | Standing audience | 1.55m | 2.0 | 2.50m |
| Seated audience | 1.15m | 1.60m | 2.10m | |
| Ray-On 110TC | Standing audience | 1.55m | 2.20m | 2.70m |
| Seated audience | 1.15m | 1.80m | 2.30m | |
| Ray-On 210TC | Standing audience | 1.70m | 2.30m | 2.80m |
| Seated audience | 1.30m | 1.90m | 2.40m | |
Table 1 – Ray-On mounting height, from floor to bottom of column (meters).
The Ray-On wall-mounting system allows the subsequent adjustment of the columns height. Cf § 5CAD Modeling
CAD Modeling
There are powerful CAD software tools that can predict the acoustics of a room and accurately model the radiation of loudspeaker arrays. These tools can calculate various acoustic indices, such as reverberation time, sound pressure level, STI, etc.
The sound radiation of the Ray-On loudspeakers can be predicted directly using CATT-Acoustic or EASE softwares.
A simple direct sound simulation tool is directly accessible on www.activeaudio.fr.
Direct sound prediction is also given in the technical characteristics section 6 on page 10.
Equalization and tuning
Ray-On loudspeakers may be used without any equalization, but using one is advised. Equalization flattens the column’s frequency response and protects the loudspeakers by filtering low frequencies.
The recommended equalization is the same for the 3 different models, which allow many columns to be put together on the same 100V line.
Two equalizations are specified:
- one for speech, which uses 4 cells (n°2-5);
- the other for music, which uses 6 cells (n°1-6).
The table 2 on the next page gives detailed information about these equalizations. The corresponding frequency curves are presented in figure 3 on the facing page.
| Type | Parameters | |
| 1 | Parametric | Freq = 100 Hz ; Gain = +6dB ; Width = 1.5 oct (Q=0.92) |
| 2 | 2nd order high-pass | Fcut = 130 Hz ; Gain = -3 dB @ Fcut (Butterworth) |
| 3 | Parametric | Freq = 280 Hz ; Gain = -3.0 dB ; Width = 1.0 oct (Q=1.4) |
| 4 | Parametric | Freq = 5 000 Hz ; Gain = +6 dB ; Width = 1.0 oct (Q=1.3) |
| 5 | Parametric | Freq = 10 700 Hz ; Gain = -7.0 dB ; Width = 0.25 oct (Q=4.0) |
| 6 | Parametric | Freq = 15 500 Hz ; Gain = +6.0 dB ; Width = 0.5 oct (Q=1.2) |
Table 2 – Recommended equalization
A subwoofer may be used to extend the low-frequency response, especially for diffusion of music. It is advised not to activate the cell 1, frequencies under 180Hz being rendered by the sub. Model SB110 is ideally suited to the Ray-On columns. See the SB110 user manual for the equalization of the system.
Installation and Wiring
Ray-On loudspeakers are vertically mounted, usually on a wall, using the supplied wall-mounting system.
The next two pages illustrate the steps to follow for column mounting.
An accessory is available for mast mounting.
Height adjustment: If changing the column’s height is necessary, take the column off its wallmounting system, move the «hook-slide» along the backside rail, then put the column back on its wall-mounting system.
100V: Power selection is made with the rotary switch.
Safety: An M5 thread is available at the back of the column designed to accommodate a ring for mounting a safety cable.
«Daisy-chain» cabling: Several bushings are available on the back of the Ray-On columns, allowing to connect the column to another Ray-On.
Good to know: The cable diameter must be less than 7.5 mm, the wire’s between 0.5 and 2.5 mm².
6.1 General Characteristics
| Ray-On 70TC | Ray-On 110TC | Ray-On 210TC | ||||
| Acoustical data 4 | 8Ω mode | 100V mode | 8Ω mode | 100V mode | 8Ω mode | 100V mode |
| Continuous power | 75W | 18W / 36W / 72W | 150W | 25W / 50W / 100W | 300W | 25W / 50W / 100W / 200W |
| SPL max | 91dB at 5m | 85 / 88 / 91dB at 5m | 92dB at 8m | 84 / 87 / 90dB at 8m | 94,5dB at 16m | 84 / 87 / 90 / 93dB at 16m |
| Sensitivity | 71dB / W at 5m | 72dB / W at 8m | 71dB / W at 16m | |||
| Freq. bandwidth at
-3dB/-10dB |
150Hz – 14,5kHz /
120Hz – 17kHz |
150Hz – 16,5kHz /
120Hz – 18kHz |
150Hz – 16,5kHz /
120Hz – 19kHz |
|||
| Range ±3dB/±5dB | 6.5 / 12m | 15 / 20 m | 31 / 42 m | |||
| Vertical directivity | Wavefront synthesis | |||||
| Horizontal -6dB opening angle | 360° at 500Hz / 190° at 1kHz 156° at 2kHz / 119° at 4kHz | |||||
| Loudspeakers | 6 loudspeakers 70x70mm, outdoor | 12 loudspeakers 70x70mm, outdoor | 24 loudspeakers 70x70mm, outdoor | |||
| Electrical data | 8Ω mode | 100V mode | 8Ω mode | 100V mode | 8Ω mode | 100V mode |
| Nominal impedance | 8 | 556 / 278 /
139 |
8 | 400 / 200 /
100 |
8 | 400 / 200 /
100 / 50 |
| Amp. power recom. | 150 W | – | 300 W | – | 500 W | – |
| Connectors | Lever terminal block, with “loop-through” | |||||
| Wire section | from 0,5 to 2,5mm² | |||||
| Protection | Thermal fuse and protection against overload | |||||
| Mechanical data | 8Ω mode | 100V mode | 8Ω mode | 100V mode | 8Ω mode | 100V mode |
| Materials | Body: aluminum ; Grid: steel treated against rust and UV | |||||
| Dimensions H x L x P | 702 x 128 x 117 mm | 1115 x 128 x 117 mm | 2082 x 128 x 117 mm | |||
| Net / shipping weight | 5.2 / 5.7 kg | 8.3 / 9.1 kg | 16.2 / 17.8 kg | |||
| Environment | IP54 ; from -25°C to +55°C, indoor / outdoor | |||||
| Colors | White (RAL9016 paintable) and Black (RAL9005) | |||||
| Mounting | Vertical mounting on a wall or on a mast | |||||
| Tuning and exploitation | 8Ω mode | 100V mode | 8Ω mode | 100V mode | 8Ω mode | 100V mode |
| Mounting height (cm) | 1.70 seating / 2.10 standing | 1.80 seating / 2.20 standing | 2.0 seating / 2.40 standing | |||
| Recom. equalization | Speech: 4 parametric cells / Music: 6 parametric cells | |||||
| Modeling | EASE and CATT-Acoustic models available | |||||
4.Unless specified otherwise, characteristics are measured with column at nominal mounting height on horizontal reflecting floor, and using recommended music
| Ray-On 70TC | Ray-On 110TC | Ray-On 210TC | ||||
| Miscellaneous | 8Ω mode | 100V mode | 8Ω mode | 100V mode | 8Ω mode | 100V mode |
| Warranty | 5 years | |||||
| Maintenance | No maintenance required | |||||
| Serial number | YYMMXXXX (YY: year – MM: month – XXXX: serial) | |||||
| Certification | EN54-24 type B for indoor and outdoor VA systems | |||||
Technical drawings
6.3 Acoustical data
Acoustical data 5.
(a) R70TC vertical directivity : sound level for the speech octaves (500Hz,1kHz,2kHz) in the vertical median plane.
(b) R70TC horizontal directivity: sound level for the speech octaves (500Hz,1kHz,2kHz) on the listening plane (60cm below the column).
(c) R70TC frequency response, with recommended music equalization. Average from 2 to 10m in the axis.
Figure 6 – R70TC : acoustical data
5. Column in nominal position at 2.30m from the floor. The reference SPL is the mean level in the listening zone.
(a) R110TC vertical directivity: sound level for the speech octaves (500Hz,1kHz,2kHz) in the vertical median plane.
(b) R110TC horizontal directivity: sound level for the speech octaves (500Hz,1kHz,2kHz) on the listening plane (80cm below the column).
(c) R110TC frequency response, with recommended music equalization. Average from 2 to 15m in the axis.
Figure 7 – R110TC: acoustical data.
(a) R210TC vertical directivity: sound level for the speech octaves (500Hz,1kHz,2kHz) in the vertical median plane.
(b) R210TC horizontal directivity: sound level for the speech octaves (500Hz,1kHz,2kHz) on the listening plane (100cm below the column).
(c) R210TC frequency response, with recommended music equalization. Average from 2 to 30m in the axis.
Figure 8 – R210TC: acoustical data
www.activeaudio.fr
info@activeaudio.fr
Tel: +33 (0)2 40 46 66 64
DOP1031_B
Documents / Resources
 |
Active audio R210TC Ray-On Single Channel Column Loudspeaker [pdf] User Manual R70TC, R110TC, R210TC, R210TC Ray-On Single Channel Column Loudspeaker, R210TC, Ray-On Single Channel Column Loudspeaker, Channel Column Loudspeaker, Column Loudspeaker, Loudspeaker |
