Acsys PL5 BLE Bluetooth Enabled Padlock User Manual
INSTALL APP
METHOD 1
- Scan this QR code
- Download the Acsys BLE mobile app for your respective platform
DO NOT SCAN the QR code on the padlock bottom cover
or on the padlock package
METHOD 2
- Search for “Acsys Mobile App” on your device app store
- Download and install the app on your device
- On the welcome screen, select “Acsys iAMS Enterprise” from the available app types
- Register the app by following the on-screen instructions
REGISTER LOCK
- Open Main Menu Add Access Point
- Enter Site ID
- Enter PIN code
- Press Register
- Add Access Point
- Enter Lock ID or scan QR Code on the lock
- Activate Lock
- Lock is registered
DELETE LOCK
- Open Main Menu Delete Access Point
- Enter Site ID
- Enter PIN code
- Press Delete
- Press the Delete button next to the correct Lock name
- Activate Lock
- Lock is deleted
OPERATE LOCK
- Enter Site ID
- Enter PIN code
- Press
Check-in or Check-out depending on the operation type
CHECK-IN
Press the Open button next to the Lock name
Lock shackle pops out Lock is open
Activate Lock
CHECK-OUT - Press the shackle and hold
- Press the Close button next to the Lock name
- Lock is Closed
JUMP START LOCK
Jump starting is used when the battery is fully depleted. It serves as a way to wake up the lock, open it and perform a battery replacement (illustrated in the next section)
- Remove the Dust Cap to uncover the USB jump-start port
- Insert a Micro USB Cable in the Micro USB port and connect it to USB wall charger or a portable power bank
- While jump-starting, the LED flashes green every 2 seconds indicating that Bluetooth is advertising during which, the lock can be opened using the mobile app. After 60 sec, the lock enters in sleep mode indicated by an orange LED glow.
- If the 60 sec have elapsed, press the Bluetooth button or remove and reconnect the USB power to put the lock in Bluetooth advertising mode again.
- Open the padlock using the mobile app and perform the battery replacement procedure shown below.
REPLACE BATTERY
- Remove the screw found at the bottom of the shackle hole
- Push the bottom plate through the shackle hole and detach it from the padlock body
- Replace the battery and reverse the previous steps to reassemble
LED INDICATIONS
| ACTION | STATE | INITIALIZED LOCK INDICATION | BLANK LOCK INDICATION |
| Press Bluetooth button | Bluetooth advertising | 1 green flash every 2 sec for 60 sec | 1 red flash every 2 sec for 60 sec |
| Press and Hold shackle | Lock is open and shackle is pushed closed | 1 green flash, every 2 sec until shackle is released | 1 red flash every 2 sec |
| Initialize, Delete Open, Close | Operation successful Operation failure | 1 quick green flash 1 quick orange flash | |
| Battery Replacement | 1 quick green flash | 1 quick red flash | |
| USB jump start | Bluetooth advertising Sleep mode | 1 green flash, every 2 sec for 60 sec orange glow | 1 red flash, every 2 sec for 60 sec orange glow |
SPECIFICATIONS
| Dimensions & Weight | 70 x 125 x 31 mm | 11mm shackle | 900g |
| Power Type | Lithium (CR2) | Non-Rechargeable | Jump-Start |
| Visual Indicator | Tricolor LED |
FCC STATEMENT
FCC ID: 2AR93-116P1948
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. SPECIFICATIONS
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Documents / Resources
 |
Acsys PL5 BLE Bluetooth Enabled Padlock [pdf] User Manual 116P1948, 2AR93-116P1948, 2AR93116P1948, PL5 BLE Bluetooth Enabled Padlock, PL5 BLE, Bluetooth Enabled Padlock, 421-024A |
