ABUS IPCS54511A Outdoor Camera

Introduction
Dear Customer,
Thank you for purchasing this product.
This device complies with the requirements of the following EU directives: the EMC Directive (2014/30/EU) and the RoHS Directive (2011/65/EU).
In order to maintain this status and to ensure safe operation, you as the user must observe these operating instructions!
Before using the product, read through the entire operating manual and observe all operating and safety instructions!
All company names and product descriptions are trademarks of the corresponding owner. All rights reserved.
If you have any questions, please contact your specialist installation contractor or specialist dealer.
Disclaimer
This user manual has been produced with the greatest of care. Should you discover any missing information or inaccuracies, please let us know about them.
ABUS Security-Center GmbH & Co. KG does not accept any liability for technical and typographical errors, and reserves the right to make changes to the product and user manuals at any time and without prior warning.
ABUS Security-Center GmbH is not liable or responsible for any direct or indirect damage resulting from the installation, performance and use of this product. No guarantee is made for the contents of this document.
Important safety information
All guarantee claims are invalid in the event of damage caused by non-compliance with this user manual. We cannot be held liable for resulting damage.
We cannot be held liable for material or personal damage caused by improper operation or non-compliance with the safety information. All guarantee claims are void in such cases.
Dear Customer,
The following safety information and hazard notes are not only intended to protect your health but also to protect the device from damage. Please read the following points carefully:
- There are no components inside the product that require maintenance by the operator. Opening or dismantling the product invalidates the CE certification and guarantee claims/warranty.
- The product may be damaged if it is dropped, even from a low height.
Avoid the following adverse conditions during operation:
- Moisture or excess humidity
- Extreme heat or cold
- Direct sunlight
- Dust or flammable gases, vapours or solvents
- Strong vibrations
- Strong magnetic fields (e.g. next to machines or loudspeakers)
- The camera must not be installed on unstable surfaces.
General safety information
- Do not leave packaging material lying around. Plastic bags, sheeting, polystyrene packaging, etc. can pose a danger to children if played with.
- The video surveillance camera contains small parts which could be swallowed and must be kept out of the reach of children for safety reasons.
- Do not insert any objects into the device through the openings.
- Only use replacement devices and accessories that are approved by the manufacturer. Do not connect any non-compatible products.
- Please pay attention to the safety information and user manuals for the other connected devices.
- Check the device for damage before putting it into operation. Do not put the device into operation if you identify any damage.
- Adhere to the normal voltage limits specified in the technical data. Higher voltages could destroy the device and pose a health risk (electric shock).
When installing the device in an existing video surveillance system, ensure that all devices have been disconnected from the mains power circuit and low-voltage circuit.
If in doubt, have a specialist technician carry out assembly, installation and connection of the device. Improper or unprofessional work on the power supply system or domestic installation puts both you and other persons at risk.
Connect the installations so that the mains power circuit and low-voltage circuit always run separately from each other. They should not be connected at any point or become connected as a result of a malfunction.
Intended use
This camera is used for indoor and outdoor video surveillance (depending on the model) in conjunction with a recording device or appropriate display unit (e.g. PC).
Use of this product for any other purpose than that described may lead to damage to the product and other hazards. All other uses are not as intended and will result in the invalidation of the product guarantee and warranty. No liability can be accepted as a result. This also applies to any alterations or modifications made to the product.
Read the user guide carefully and in full before putting the product into operation. The user guide contains important information on installation and operation.
Explanation of symbols
The triangular high voltage symbol is used to warn of the risk of injury or health hazards (e.g. caused by electric shock).
The triangular warning symbol indicates important notes in this user manual which must be observed.
This symbol indicates special tips and notes on the operation of the device.
This user manual describes the software functions in the camera browser interface. For information about how to install the hardware for the respective camera, please read the quick start manual or the hardware installation manual, if you have it.
You can download a PDF version of the user manuals in your language at www.abus.com via the product search.
Connections and functions
Power supply
ATTENTION! Before you begin the installation, make sure that the supply voltage and the nominal voltage of the camera match.

Installation
- Cover ring
- Camera Head
- Fixing cap
- Base plate with fixing screw
Method
- First, remove the cover ring by turning it counterclockwise.
- Then gently loosen the fixing screw on the base plate.
If required, the camera head and fixing cap can be completely removed from the base plate. Remove the fixing screw completely.
- Use the supplied drilling template to mark the mounting holes. Depending on the substrate, please use suitable dowels and screws. Then fix the bottom plate.

- For cable routing, drill a suitable hole in the middle of the floor panel in the ground, or use the optional box hole on the floor panel for side cable routing (in this case, the cable must be routed sideways before installing the floor panel).
- Then attach the camera head with fixing cap and fix the fixing screw lightly.

Alignment of camera
A: Pan
B: Tilt
C: Rotation
Tighten the fixing screw to the desired orientation of the camera head.

Reset to factory default
The Reset Settings button is located on the side of the camera head behind a cover plate.
- Disconnect the camera.
- Press and hold the “Reset” button on the camera.
- Now connect the power supply to the camera (via 2-pin power supply or Power-over-Ethernet) and press the “Reset” button for another 30 seconds.

SD-Card slot
To install the micro SD card, first remove the cover on the side of the camera head.
Max. SD card size: 256 GB

After installing the Micro-SD card, the card must be formatted before it can be used.
Usage of Connector cover
The plug protection serves to improve the protection against environmental influences such as dust and moisture.

When using the connector protection, the Ethernet connector must always be crimped. Use with pre-assembled Ethernet cables with plugs is not possible.
Installation on Wall mount
The wall mount TVAC32500 / TVAC32500X is available for the installation (please investigate alternative model via the product search under www.abus.com).

Installation on junction box
An installation box TVAC32500 / TVAC32500X is available for installation, in order to make cable connections if necessary (please research alternative model using the product search at www.abus.com).

Notes for usages of integrated White Light LEDs
The LED range is heavily dependent on the ambient conditions. If the surroundings in the camera’s field of view are poorly reflective, or if there is no object within the maximum illumination range, the brightness of the video image may be too low at night. This results in poor usability of the video image.
Furthermore, when installing the camera, make sure that there are no objects in the immediate vicinity (e.g. gutter or wall) around the camera’s field of view. In this case, reflections of the LED light from these objects can occur. The effects in the video image would be ring-shaped dissolves in the opposite direction of the object.
The LED range can be reduced by strongly absorbing surfaces (e.g. asphalt).
Maintenance and cleaning
Function test
Regularly check the technical safety of the product, e.g. check the housing for damage.
If it appears to no longer be possible to operate the product safely, stop using it and secure it to prevent unintentional use.
It is likely that safe operation is no longer possible in the event that:
- the device shows signs of visible damage
- the device no longer works correctly
- the device has been stored in adverse conditions for a long period of time
- the device has been exposed to stresses during transportation.
Please note: You do not need to perform any maintenance on the product. There are no components requiring servicing or checking inside the product. Never open it.
Cleaning
Clean the product with a clean, dry cloth. The cloth can be dampened with lukewarm water to remove stubborn dirt.
Make sure that no liquids enter the inside of the device, as this will destroy it. Do not use any chemical cleaning agents, as these could damage the surface of the housing.
Disposal
Devices displaying this symbol may not be disposed of with domestic waste. At the end of its service life, dispose of the product according to the applicable legal requirements.
Please contact your dealer or dispose of the products at the local collection point for electronic waste.
Documents / Resources
![]() | IPCS54511A Outdoor Camera |
References
- User Manualmanual.tools

