A-OKTECHNOLOGY-logo

A-OKTECHNOLOGY AC127 Remote Control

A-OKTECHNOLOGY-AC127-Remote-Control-product

Features

  1. The appearance is fashionable and elegant, which can be applied to different decoration styles;
  2. The surface is treated with piano paint, which is unique and noble;
  3. Ultra-thin body, showing simple fashion;
  4. High hardness acrylic panel to ensure flawless appearance;
  5. Optional magnetic base for easier installation;
  6. Ultra-low power consumption design;
  7. Universal CR2032 button battery, more convenient to install and purchase.

Parameters

 

Model

RF transmit

frequency

 

RF remote control distance

Transmit power Transmit current Standby

current

 

Battery

Working Temp. Size
 

AC127-02

 

433.92MHz

 

>80m

 

>10mW

 

>15mA

 

>20uA

 

 

CR2032(6V)

 

-2o•c – +55°C

1tT'(!.:;i1 \mm

lnstallation

  1. The minimum distance between the transmitter and ground is 1.5m.
  2. The minimum distance between the receiver and the transmitter is 1 m.
  3. Do not install on a metal object, or the transmit distance will be affected.
  4. Do not install it in a damp and sun exposed place, otherwise the service life will be affected .

cautions
Please observe the following regulations while complying with the effective electricity standards:

  • Transmit range: within 80 meters in open space
  • Avoid static interference, which may damage the electronic components.

A-OKTECHNOLOGY-AC127-Remote-Control-fig- (1)

0petations

A-OKTECHNOLOGY-AC127-Remote-Control-fig- (2)

  1. Control
    • Make curtain up
    • Make curtain stop
    • Make curtain down
  2. Channel selection
    • Right select key: Channel increment
    • Left Select key: Channel decrement
  3. Channel-lock (Available for 6 and 16 channels) Channel-Lock: Press Mstop” + “right or left select key” 3s till the LED lights to lock current channel, after the operation done, other channel cannot be used except for the locked channel.

Trouble shooting

Problems Analysis Solutions
 

When operating the transmitter, the receiver no act

1.The receiver is not working properly 2.The battery of transmitter is out

of power

 

A. The receiver works normally

B. Replace a new battery of transmitter

 

The receiver is not working properly

 

The battery of transmitter is out of power

 

Replace a new battery of transmitter

cautions

  • The statement “Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children.
  • Do NOT dispose of batteries in household trash or incinerate.
  • The statement “Even used batteries may cause severe injury or death.
  • The statement “Call a local poison control center for treatment information.
  • A statement indicating the compatible battery type (e.g., LR44, CR2032).
  • A statement indicating the nominal battery voltage.
  • The statement “Non-rechargeable batteries are not to be recharged.
  • The statement “Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
  • The statement “Ensure the batteries are installed correctly according to polarity (+ and-).
  • The statement “Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • The statement “Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • The statement “Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

FCC rules

  • This device complies with Part 15 of the FCC rules. Operation is subjected to the following two conditions:
    1. this device may not cause harmful interference, and
    2. this device must accept any interference received, including interference that may cause undesired operation.
  • Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
  • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are d esigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.
  • This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED) Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
    1. this device may not cause interference, and
    2. this device must accept any interference, including interference that may cause undesired operation of the device.
  • The device has been evaluated to meet general RF exposure requirement.

FAQs

What is the maximum distance for remote control operation?

The RF remote control distance is greater than 80 meters in open space.

What type of battery does the remote control use?

The remote control uses a CR2032 button battery (6V).

What should I do if the receiver is not responding?

Check if the battery of the transmitter is out of power and replace it if necessary. Also, ensure that the receiver is working properly.

Can I install the transmitter on a metal surface?

No, installing on a metal object can affect the transmit distance.

What precautions should I take when handling batteries?

Do not dispose of batteries in household trash or incinerate. Ensure batteries are installed correctly according to polarity, and do not mix old and new batteries.

Documents / Resources

A-OKTECHNOLOGY AC127 Remote Control [pdf] Owner's Manual
AC127, 2AVVD-AC127, 2AVVDAC127, AC127 Remote Control, AC127, Remote Control, Control

References

Leave a comment

Your email address will not be published. Required fields are marked *