A LED Q290 Ceiling LED Light
Important: Please read the instruction manual carefully prior to installation and keep it for future reference.
Ordering Code |
Product | Power (W) | Function Description |
Fitting Series | |||
Sensor DIM, | |||
Brida Sensor CCT Skumringsrelæ | Brida | 18 | color temperature selectable, power switchable |
Accessories
No. | Pic. | Qty. | Usage |
1 | ![]() |
3 | Fix light |
2 | ![]() |
3 | Rawl plug |
3 | ![]() |
1 | Vandal-proof screw tool |
4 | ![]() |
3 | Plastic washer |
5 | ![]() |
2 | Fix cable clip |
6 | ![]() |
1 | Cable clip |
7 | ![]() |
1 | Cable clip |
8 | ![]() |
4 | Plastic plug |
- Mounting: Wall or Ceiling
- Light features:
- Ra: >80
- Life Time: 5 years
- Light Source: LED SMD2835
- Input: 220V-240V 50/60Hz
CCT:
Electric Current | Power |
350mA | 10W |
500mA | 14W |
550mA | 15W |
700mA | 18W |
Colour Temperature Code
Code | Colour Temperature | CCT(K) | Lumen |
30K | Warm White | 3000 | 2142 |
35K | Natural White | 3500 | 2196 |
40K | Cool White | 4000 | 2232 |
Installation
- Unscrew the diffuser anticlockwise.
Vertically remove the diffuser and PCBA. - a. Cut off the power. Thread the input cable through the rubber plug to the fixture. Connect the L, N wire referring to the wiring diagram.
b. Knock the rawl plugs into the pre-drilled holes on ceiling/wall. Wear plastic washers on self-tapping screws and tighten them to fix the fixture on ceiling/wall. - Install the cable clip.
- Connect the DC cable.
- Mount the diffuser onto the base with screws.
- Install the plastic plugs to hide the screws.
Wiring
Sensor Setting Options
Sensitivity
Sensitivity can be adjusted by selecting the combination on the DIP switches for different applications.
Hold-time
Hold-time refers to the time period that the light remains 100% on if no more movement is detected.
Daylight sensor
Different daylight threshold can be preset on DIP switches.
Light will always turn on upon movement if daylight sensor is disabled.
Stand-by time
This is the time period that the light remains at a low level before it is completely turned off.
Stand-by dim level
Light can be dimmed to different levels after hold-time.
Detection Pattern
Maintenance
- Cut off the main power first.
- Don’t touch LEDs while maintaining or cleaning.
- Don’t use chemicals to clean the fixture.
Environmental protection: waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Caution
- The product must be installed by professional technicians and power supply must be cut off before installation.
- The diameter for AC input wire is 0.75mm² (complying with 60245 IEC57), which complies with the latest IEE electrical standards or national standards.
- Do not touch the electronic circuit and its components.
- Contact an authorised technical service centre for any repairs possibly required use only original spare parts.
- Do not touch LED while installing or maintaining.
- Sealing the entrance hole with glue after install is needed.
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
Instruction for Light Source Disassembly
- Unscrew the diffuser anticlockwise and vertically take it out.
- Disconnect the DC power cable from the driver.
- On the reverse of diffuser, use the screwdriver to pry the clips to release the PCBA, then twist the PCBA anticlockwise.
- Take out the PCBA (light source) from the diffuser.
This product contains a light source of energy efficiency class <D>
A LED A/S Hammeren 6, DK-6800 Varde www.aled.dk +45 71995354
Documents / Resources
![]() |
A LED Q290 Ceiling LED Light [pdf] Instruction Manual Q290, Ceiling LED Light, LED Light, Ceiling Light, Light, Q290 LED Light |