WinCT-UFC Windows Communication Tools Software
User Manual
WinCT-UFC Set Up _EN_ Ver. 2.20 for Windows 10 / Windows 8.1 / Windows 7 Copyright (c)
2020 A&D Company, Limited
Setup
WinCT – UFC (Windows Communication Tools for UFC)
This software “Windows Communication Tools for UFC” (“WinCT-UFC”) serves as the Windows setting tools for editing UFC Output Format on a PC to output from an A&D weighing instrument equipped with the UFC function and for storing it in the weighing instrument.
Below are instructions for the installation and use of WinCT-UFC.
System Requirements
1-1.PC
OS: Microsoft Windows 10 / Windows 8.1 / Windows 7
1-2.Weighing instruments
WinCT-UFC can be used with the following A&D weighing instrument equipped with the UFC function (see table below).
As of May 2022
| Weighing instrument | Model |
| Precision balances | BA series |
| BA-T series (The touch panel software version 1.01 s or later) |
|
| GX-A/GF-A series | |
| GX-M/GF-M series | |
| Counting scales | FC-i/FC-Si series |
| HC-i series | |
| Digital platform scales | HV-C/CP and HW-C/CP series |
| Checkweighing scales | FS-i series |
1-3. Cable Please refer to the manual of the intended model.
Note – Back up important data in the PC before installing WinCT-UFC.
Installation Instructions
Step 1 If a previous version of WinCT-UFC is installed on the PC uninstall it.
Step 2 Close all open applications in Windows.
Step 3 Install WinCT-UFC. Run Setup-UFC.msi.
Step 4 The setup wizard is displayed. Please click [Next].
Step 5 Select the installation folder, and click [Next].
Step 6 Click [Next].
Step 7 Installation will start. Please wait for a while to complete it.
Step 8 When the installation is complete, click [Close] to finish.
Starting WinCT-UFC
Select WinCT-UFC from the START menu. The default menu address is [Start] – [program] – [A&D WinCT-UFC]. You will find the instruction manual in the Readme file under [A&D WinCT-UFC].
Note – WinCT-UFC is a program for balances that use the A&D format. A&D does not guarantee performance or
compatibility when other manufacture’s balances are used with WinCT-FRD. – If you have problems or questions about compatibility with third-party software, contact the manufacturer
for information.
License Agreement and Limited Warranty
- WinCT-UFC is subject to change without notice and does not represent a commitment by A&D to support earlier versions or to make changes to support nonstandard computers.
- WinCT-UFC is intended for the transmission of data from an A&D balance to a PC, and command transmission for controlling the balance.
- Under copyright laws, the WinCT-UFC program may not be copied, in whole or part, without the consent of
A&D, except as specified in the license agreement. - WinCT-UFC should only be installed on the hard disk or peripheral storage devices of a PC connected to an A&D weighing instrument.
- A&D bears no liability for direct, indirect, special, incidental, or consequential damages resulting from any defect in the WinCT-UFC program or the readme file, even when advised of the possibility of such damage.
- A&D is not responsible or liable for the loss of any programs and/or data stored in the PC on which WinCT-UFC was installed, including the costs of recovering said lost programs or data.
Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation.
Uninstallation Instructions
-Use the “Add/Remove Programs” icon in the control panel to remove this program from your PC.
Documents / Resources
 |
A D WinCT-UFC Windows Communication Tools Software [pdf] User Manual WinCT-UFC, Windows Communication Tools Software, Communication Tools Software, Tools Software, WinCT-UFC, Software |
