N8520-32D

DATA CENTER SWITCH

Quick Start Guide V1.0

Introduction

Thank you for choosing the Data Center Switch. This guide is designed to familiarize you with the layout of the switch and describes how to mount it.

N8520-32D

Accessories

Power Cord x2         Grounding Cable x1        Console Cable x1

Front-Post Bracket x2       Rear-Post Bracket x2         Rear Mounting Ear x2

Bracket-Mounting Screw x20        Ear-Locking Screw x2

NOTE: The accessories may vary from illustration, please prevail in kind.

NOTE: This power cord cannot be used with other devices, and other power cords should not be used with this device.

Hardware Overview

Front Panel Ports

1. 1PPS Timing
2. MGMT
3. USB
4. SFP+
5. QSFP-DD
6. RJ45 Console
7. Micro-USB Console

Front Panel Button

1. Reset

NOTE: For information on LEDs, check the PicOS manual or hardware guide online, or ask the technical support personnel for help.

Installation Requirements

Before the installation, make sure that you have prepared the following items:

• Standard-sized, 19-inch-wide rack with a minimum of 1U height available.
• Category 5e or higher RJ45 Ethernet cables, fiber optical cables, and console cables.
• Phillips screwdriver and adjustable wrench.
• ESD bracelet, ESD gloves, or ESD clothing.
• Cable ties, marker, and utility knife.

Site Environment

• Make sure that the operating temperature is maintained within 0°C to 45°C.
• Make sure that the operating humidity is maintained within 5% to 95%.
• Make sure that the installation site is well-ventilated to ensure sufficient airflow around the switch.
• Make sure that the installation site is free of dust, leaks, drips, heavy condensation, and moisture.
• Make sure that the rack is properly grounded.
• Avoid installing the equipment against the wall to facilitate heat dissipation and maintenance, and make sure that there is adequate space around its four sides.

Mounting the Switch

Rack Mounting

1. Attach the front-post brackets and rear-post brackets to the two sides of the switch using the bracket-mounting screws.

2. Secure the switch to the rack by fastening the front and rear mounting ears with self-provided screws and cage nuts.

3. Lock the position of the rear mounting ears using the ear-locking screws.

Grounding the Switch

1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the switch is mounted.
2. Securely connect the other end of the grounding cable to the switch back panel using the screw and the washer.

CAUTION: The earth connection must not be removed unless all supply connections have been disconnected.

Connecting the SFP+ Port

1. Insert a SFP+ transceiver into the switch.
2. Connect a fiber optic cable to the transceiver. Then connect the other end of the cable to other fiber devices.

Connecting the QSFP-DD Ports

1. Insert a QSFP-DD transceiver into the switch.
2. Connect a fiber optic cable to the transceiver. Then connect the other end of the cable to other fiber devices.

Connecting the RJ45 Console Port

1. Connect the RJ45 end of a console cable to the RJ45 console port of the switch.
2. Connect the DB9 end of the cable to the serial port of a computer.

Connecting the MGMT Port

Connect the MGMT port of the switch to a computer with a standard RJ45 Ethernet cable.

Connecting the USB Port

Insert a Universal Serial Bus (USB) flash disk into the USB port of the switch.

Connecting the Power

Install one or two AC PSUs and connect them to an AC power source.

NOTE: When using a single AC PSU to power a fully loaded system, a high-voltage power supply (200-240 VAC) must be used.

Troubleshooting

Power Module Failure

• Check if the power module is compatible with the equipment.
• Check if the power cord is fully seated. Unplug and reconnect it.
• Clean accumulated dust from the power module if present.

Fan Module Failure

• Check if the fan module is fully seated. Unplug and reconnect it.
• Clean foreign matters from the air intakes and air outlets if present.

Serial Port Failure

• Check if the serial port cable is correctly connected at both ends.
• Check if the serial port parameters (e.g., baud rate, stop bits) are correctly configured.

MGMT Port Failure

• Check if the Ethernet cable is correctly connected at both ends.
• Check if network interface settings (e.g., IP address, subnet mask) are correctly configured.

If the above issues persist, please contact technical support.

Product Warranty

FS ensures our customers that for any damage or faulty items due to our workmanship, we will offer a free return within 30 days from the day you receive your goods. This excludes any custom-made items or tailored solutions.

Warranty: The product enjoys a 5-year limited warranty against defects in materials or workmanship. For more details about the warranty, please check at https://www.fs.com/policies/warranty.html 

Return: If you want to return the item(s), information on how to return can be found at https://www.fs.com/policies/day_return_policy.html

Online Resources

For additional technical documents, visit:
https://www.fs.com/technical_documents.html

Download the FS App

Scan the QR code to download and install the FS app from the App Store or Google Play Store or go to https://www.fs.com/appdownload.html

Q.C. PASSED

Copyright © 2025 FS.COM All Rights Reserved.

Documents / Resources

FS N8520-32D Data Center Switch [pdf] User Guide N8520-32D, N8520-32D Data Center Switch, Data Center Switch, Center Switch, Switch

References

• User Manual