TESLA 27MH949BU LCD Monitor User Manual

NOTE
This device is intended for household use exclusively. Professional and/or commercial use of a device intended for household purposes shortens its working life and has a negative effect on the device’s performance characteristics.

SAFETY PREVENTION MEASURES

• Please always place this device on a stable surface; otherwise, it may fall and be damaged.
• The altitude and the tropical environment the adapter fits depend on which adapter is used for the device. The rating plate on the back of the device with the above warning sign indicates that this product is applicable for the safe use of the region with altitude of 2,000m and below.
• Do not hold the plug with wet hand; otherwise, electric shock may occur. Make sure the plug has a good touch because poor touch may cause fire.
• Do not use a broken power plug nor keep apower cord near heat source; otherwise, electric shock or fire may occur.
• When cleaning the device, be sure to remeove the power plug, use a piece of soft cloth rather than industrial chemical to clean the device, be sure not to let water enter the device.
• Do not disassemble this device without permission. In case of failure, be sure to contact a professional servicing person to fix it. The unauthorized disassembly of this device may result in electric shock or fire.
• In case of rare smell or noise out of this device, be sure to immediately cut off the power supply and ask a professional servicing person to fix the problem.
• When this device is idle for long time, be sure to power it off; otherwise, electeic shock or fire may occur.

Note:
The device with AC switch may use such AC switch as cut-off component.
The device without AC switch may use power plug or coupler as cut-off component. In case of the normal use off the equipment, make sure the cut-off component can be accessed easily.

If your equipment uses an AC adapter:
– Only use the AC adaptor provided with your product.
– Do not use the power cord with other products.

This product incorporates HDMI technology.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are teademarks or registered trademarks of HDMI Licensing LLC.

INSTALLATION INSTRUCTIONS

1. Open the cardboard packaging and remove the monitor and the base together, placing them flat on a level table.
   
2. Remove the upper base, take off the plastic bag covering the monitor, and then place the monitor back into the lower base.
   
3. Install the stand onto the base interface and secure it with the screws located underneath the base.
   
4. Attach the assembled stand onto the stand slot until you hear a “click,” and then shake the stand by hand to ensure it is securely installed.
   Tip: Press the quick release button on the stand slot to detach the stand.
   
5. Lift the assembled monitor with both hands and stand it upright on a flat surface.
   Caution: Do not touch the LCD screen directly while standing up the monitor to prevent screen damage.
   

Accessories

(The above pictures are for ilustrion only and the physical accessories shall govern.)

Angle Adjustment

The screen can be adjusted by inclining forward and backward; however,the specific adjustment depends on the specific model of the device. Generally, it may be inclined 5±2° forward and 15±2° or 20±2° backward.

When adjusting the angle of the monitor, be sure not to touch or press the area of the screen.

Connect the Monitor to PC

Before connecting the LCD monitor to the PC, please power down the PC and the moitor.

Warning: Always use the power cord of standard configuration.

1. Power Plug
   Connect the power cord of the monitor into the POWER port in the back of the monitor.
2. VGA Port
   Connect the VGA cable into the VGA IN port in the back of the monitor (this needs the support of the monitor).
3. DVI Port
   Connect the DVI cable into the DVI IN port in the back of the monitor (this needs the support of the monitor).
4. HDMI Port
   Connect the HDMI cable into the HDMI IN port in the back of the monitor (this needs the support of the monitor).
5. DP Port
   Connect the DP cable into the DP IN port in the back of the monitor (this needs the support of the monitor).
6. Type C Port
   Connect the Type C cable into the Type C IN port into the back of the monitor (this needs the support of the monitor).
7. USB OUT Port
   Connect the USB cable into the USB OUT port in the back of the monitor (this needs the support of the monitor).
8. USB IN Port
   Connect the USB cable into the USB IN port in the back of the monitor (this needs the support of the monitor).
9. Audio Interface
   Connect the AUDIO cable to the AUDIO OUT port in the back of the display (this needs the support of the monitor).
   (The above pictures are for ilustrion only and the physical accessories shall govern.)

USER SETUP

Description of Keys’ Functions

Ordinary 5 Key Description
Press any button to enter the menu except the power button ( ).
Other keys – subject to the corresponding description on the monitor.

Description of Joystick Buttons
( ) Short press to power on / Long press for 3 seconds to shut down
Power on — short press any button to enter the navigation menu.
Other keys – subject to the corresponding description on the monitor.

Note: The physical keys of the specific model shall govern.

FUNCTIONS OF OPERATING MENU (OSD)

Note: The above functions may be adjusted due to different models or software version upgrades, the actual model shall prevail.

FAQ

• The lamp effect is a decorative article. If you need to standby and save electricity, you can turn it off. (Note: Standby power consumption is based on the shutdown effect).
• HDR need to be supported under Win10 system or HDR chip source.

www.tesla.info

Documents / Resources

TESLA 27MH949BU LCD Monitor [pdf] User Manual 27MH949BU, 27MH949BU LCD Monitor, 27MH949BU, LCD Monitor

References

• User Manual