RCA RPJ199COMBO Bluetooth Theater Projector

Important Safety Instructions

1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifier) that produces heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
13. use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

Additional Warnings and Precautions

1. Do not look directly into the projector light.
2. Don’t touch the project lens
3. Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.
5. WARNING: Changes or modified to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
6. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.
7. WARNING: Shock hazard – Do Not Open.
8. Caution and marking information is located at the rear or bottom of the apparatus.
9. WARNING: To reduce the risk of fire or electric shock, do not expose this, apparatus to rain, moisture, dripping, or splashing.
10. Objects filled with liquids, such as vases, shall not be placed on the apparatus.

FCC Warning

FCC ID: LCS180515064AE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

in the box

Remove & Close The Lens Cover

Placing Your Projector

Your projector can be installed in four different configurations ( see picture below):

• Front Table: Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.
• Front Ceiling: Select this location with the projector suspended upside-down from the ceiling in front of the screen. NOTE: A projector mount is required to install the projector in a ceiling.
• Rear Table: Select this location with the projector placed near the floor behind the screen. NOTE: A special rear projection screen is required.
• Rear Ceiling: Select this location with the projector suspended upside-down from the ceiling behind the screen. NOTE: A projector mount is required to install the projector in a ceiling. A special rear projection screen is required.

to reduce image distortion

It is recommended to move the projector as close to the center of the screen.

Distance Between The Projector And Screen

Measure the distance between the projector and where you want to position the screen. This is the projection distance.

Placing Your Projector On the Ceiling

When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount. Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt, please ask the advice from an installation professor. NOTE: Projector mount and screw(s) not included

Adjust The vertical location

Adjust The Focus And Keystone

Follow the below picture to adjust the focus and trapezoidal screen. Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center. A keystone image is created when the projector beam is projected to the screen in an angle. Keystone correction will restore the distorted image to a rectangular or square shape.

Controls Of Remote

Install / Remove the Battery Of the Remote Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (not included), referring to the polarity markings. Finally, replace the cover. NOTES

• Batteries shall not be exposed to excessive heat such as sunshine, fire
• Be sure that the batteries are installed polarity correctly.
• Do not mix old and new batteries.
• Only same or equivalent type batteries as recommended are to be used.
• Do not dispose of batteries in a fire, battery may explode or leak. Do not try to recharge a battery

Controls Of Projector

1. POWER Button
2. RETURN Button
3. NETVIGATOR Buttons
4. MENU E Button
5. SOURCE Button
6. TRAPEZOIDAL ADJ. Knob
7. FOCUS ADJ. Knob
8. LENS
9. EARPHONE Jack
10. AV OUT Jack
11. Micro SD Card
12. HDMI Port 1
13. HDMI Port 2
14. USB Port
15. DC IN jack
16. VGA Port
17. POWER on Indicator
18. IR Window ( Rear Side)
19. IR Window ( Front Side)
20. ANGEL ADJ. Knob

Install Power Adapter

Follow below picture to connect power adapter Connect small end of adapter FIRST. Plug the adapter body to power outlet.

Main operation

• Press the button to turn on unit, press again to turn off.
• SOURCE – Press the button to select input source.
• MENU – Press the button to enter projector menu.
• press the buttons to select screen item of projector menu.
• EXIT – Press the button to exit the projector menu.
• Press the buttons to fast search forward and rewind on USB / TF.
• Press the buttons to search next or previous file on USB / TF.
• VOL+ / VOL – Press the buttons to select correct sound.
• Press the button to play/pause the connect USB / TF card.
• FLIP – Press the button to rotate / mirror projector screen
• ZOOM – Press the button to select image scale.
• Press to mute the audio sound of your projector.Press again to resume.

Connect HDMI Show The Image On Projector Screen

Follow below picture to connect the HDMI cable and the device.

1. turn off the unit before connecting HDMI cable.
2. Press the / SOURCE device will show on the projector screen. There are 2 HDMI input, HDMI1 interface corresponds to HDMI 1 in SOURCE mode , and HDMI2 interface corresponds to HDMI 2 in SOURCE mode.
3. Press the button to turn off the unit power.

HDMI HD signal input : this interface can be input with an HD player hdmi output at the connection

Connect AV Show The Image On Projector Screen

Follow below picture to connect the AV cable and device.

1. Turn off the unit before connecting AV cable.
2. Use AV cable to connect follow below figure
3. After connecting, press the button to turn on unit and the power indicator will light up GREEN
4. Press the / SOURCE button to AV mode and the video of AV will show on the projector screen.
5. Press the button to turn off unit power.

Connect VGA Show The Image On Projector Screen

Follow the below picture to connect the HDMI cable and the device.

1. Turn off the unit before connecting VGA cable.
2. Press the button to turn off power of your projector before connection.
3. Press the button to turn off unit power.

Please refer to the following table to adjust the output signal from the computer.

PC	VGA	640×480	31.5	60
			34.7	70
			37.9	72
			37.5	75
	SVGA	800×600	31.4	50
			35.1	56
			37.9	60
			46.6	70
			48.1	72
			46.9	75
	XGA	1024×768	40.3	50
			48.4	60
			56.5	70

Connect Audio Output ( Aux Out / Line Out / Earphones)

Follow below picture to connect audio cable and device.

1. Press the button to turn off power of your projector before connection.
2. Use audio cable to connect follow below figure.
3. After connect and turn on both units. Your projector sound from external device now.
4. After using , turn off both unit

Install USB Device And Micro Sd Card “TF”

Follow below picture to install the USB and TF card Turn off the unit before install USB / TF card.

Using TF Card And USB Playback (Media Player)

Using USB playback (Media Player)

Install USB : 

1. Turn off the unit before installing the USB device.
2. Install the USB device into the USB port.
3. After connecting, press the )button to turn on unit and the power indicator light GREEN.
4. Press the direction button to select the movie icon in home menu and press “ok” to enter, and use the direction button to select the video file on the USB disk and press “OK” to play the video file on the U disk.
5. Press the “home” menu or”return” button on the remote control to return to the home menu, use the direction button to select “Music ” and press OK to enter, and use the direction button to select the required music to play on the USB disk.
6. Press the “home” menu or”return” button on the remote control to return to the home menu, use the direction button to select “Photo ” and press OK to enter, and use the direction button to select the required photo to display on the USB disk NOTE: Remove the USB, press the button to turn off power FIRST.

Using Projector Menu 1.0

Press the button to enter the projector menu. Press again to the previous status.USE  buttons to select manual page. This manual showed on right upper of view screen.

Color temper… (temperature)
Customer define	Parameter
red	0-100
blue	0-100
green	0-100

Aspect Ratio
4:3	The signal in a 4:3 aspect ratio projection image
16:9	The signal in a 16:9 aspect ratio projection image

Using Projector Menu 2.0

Press button to enter projector menu. Press again to previous status. USE buttons to select manual page. This manual showed on right upper of view screen.

Sound Mode – User	Parameter
Treble	0-100
Bass	0-100

Using Projector Menu 3.0

Press button to enter projector menu. Press again to previous status.

English	Hrvatski	Nederlands	Chinese
Franais	Deutech	Slovenina	Slovak
Espanol	Italiano	Norsk
Portugues	Magyar	Srpski
Esky	Polski	Svenska
Dansk	Romnete	Suomi

Using Projector Menu 4.0

press button to enter projector menu. Press again to previous status. use buttons to select manual page. This manual showed on right upper of viewing screen.

Specifications

Light Source Type	LED
Brightness Output	White light output ANSI: 215 lm  White Brightness output ANSI: 159 lm
Display Native Resolution	1920 x 1080
HDMI Input Supported    Video Resolution.	1080p , 1080i , 720p, 576i , 480p, 480i
Power Consumption	Operating 133W; Standby 0.8W
Power Input    Connect Included Adapter	DC 19V , 7.0A
Included Adapter    Connect DC input of unit	Input AC100-240V,50/60Hz    Output DC19V , 7.0 A
Color Temperature	7000-8000K

Projection Size	24-165 inch
Signal Port	VGA / HDMI / AV
USB 1 Port	Support USB device up to 32GB  Support format mpeg1, Mpeg2 ,mpeg4, mp3 , Jpeg
Weight	2.6 KG
Dimension	320 x 275 x 117mm
Speaker	2*5W
Projection distance	1m-6m

TROUBLESHOOTING

Please visit go.roku.com/rss for any questions about the Roku ® Streaming Stick .® For any other issues related to the projector function please contact Customer service: 1-800-968-9853. Before resorting the maintenance service, please kindly check by yourself with the following chart.

Symptom

Cause (and Remedy)

No Image is Projected or a “No Signal” message is displayed

1.  Power light is on. If it is not on, check the projector is plugged into the mains, that the socket is switched on, and then press the power button on the projector.  2.  Check the lens cover has been removed. 3.Check the cables are securely attached and installed as per the User Manual. 4.  The image source may not be set correctly. Press the Source button on the Control Panel or the Remote, to select the correct setting. 5.  Check in the Menu section under Video input signal to make sure that has been set correctly.

The Lamp (Bulb) switches off after a period of time	Is the warning light indicator red? If so, the projector is overheating which turns the light off automatically.  1.Leave the projector to cool for a few moments. 2.Once cooled, check nothing is blocking the ventilation vents. 3. Check the air filter is clean and clean if necessary. 4. Turn on the projector. If the issue persists please contact your support provider for further assistance.
The Image is wider at the top/bottom of the screen	This is called keystone and is due to the projection angle not being perpendicular to the screen. To correct use the projectors inbuilt keystone function to adjust the image.
Spots on the screen	Using a vacuum cleaner to clean the lens. If cleaning doesn’t resolve things, please contact your support provider for further assistance.
The image brightness has faded	This could possible be caused by the ambient light in the room. If not ,the chances are that you need to replace the lamp (bulb).
Roku®Streaming Stick® will not power on	The Roku ® Streaming Stick ® needs to be properly connected to power in order to function. For optimal performance, use the included USB cable to connect to the USB 2 port on the projector.
You cannot see the video from your Roku® Streaming Stick®on your projector	First, make sure the projector is turned on and set to the HDMI ® 3 input. Then press a button on the Roku remote control to ensure that the Roku device is not in standby or screensaver mode. Listed below are the most common reasons you may not see video on your projector:  1. You have the wrong input (source) selected on your projector. Look to see which input you have the Roku ® Streaming Stick®connected to. Press this button, it may display a menu with a choice of inputs, Use the arrow buttons on the projector remote to select the correct input and then press OK. 2. The Roku ® Streaming Stick® is not connected properly. Ensure it is firmly connected to the HDMI 3 connector on your projector. 3. If all else fails, disconnect and reconnect all cables including the power cable. For more help visit: go.roku.com/usingroku.

For service assistance and product information, please call: 1-800-968-9853. Pour obtenir assistance et information appelez: 1-800-968-9853. Curtis International Ltd. 7045 BECKETT DRIVE, UNIT 15, MISSISSAUGA, ON, L5S 2A3 www.curtisint.com

90 day Year Warranty

This product is warranted to be free from defects in material and workmanship for a period of ninety (90) days from the date of original purchase. During this period, your exclusive remedy is repair or replacement of this product or component found to be defective, at our option; however, you are responsible for all costs associated with returning the product to us. If the product or component is no longer available, we will replace with a similar one of equal or greater value. Prior to a replacement being sent, the product must be rendered inoperable or returned to us. This warranty does not cover glass, filters, wear from normal use, use not in conformity with the printed directions., or damage to the product resulting from accident, alteration, abuse, or misuse. This warranty extends only to the original consumer purchaser or gift recipient. Keep the original sales receipt, as proof of purchase, is required to make a warranty claim. This warranty is void if the product is used for other than single-family household use or subjected to any voltage and waveform other than as on the specified rating on the label (e.g., 120V 60Hz). We exclude all claims for special, incidental, and consequential damages caused by breach of express or implied warranty. All liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such warranty or condition is limited to the duration of this written warranty. This warranty gives you specific legal rights. You may have other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties or special, incidental, or consequential damages, so the foregoing limitations may not apply to you. For faster service, locate the model, type, and serial numbers on your appliance.

FAQS

References

• User Manual