BOSCH HND679LS67 Built in Stove Set

Specifications

• Model Number: 9001703689
• Language Options: German, English, Swedish, French, Finnish, Italian, Dutch, Danish, Norwegian
• Weight Capacity: 60 kg
• Accessories: Adapter (Article Number: 744661)

FAQ

Q: What should I do if the hob and oven don’t match?

A: If the hob and oven do not match as indicated by the green sticker on the oven, order a suitable adapter (Article Number: 744661) from customer service.

General information

• Read this instruction manual carefully.
• Only a licensed expert may connect the appliance.
• Improper installation, opening of the appliance, connection or assembly may lead to a loss of validity of the product war-ranty.
• Switch off the power supply before carrying out any work.
• After installation, ensure that the user does not have access to the electrical components.
• Never use this appliance in boats or in vehicles.

Safe installation

Follow these safety instructions when installing the appliance.
The appliance can only be used safely if it is correctly installed in accordance with the installation instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation location.

WARNING ‒ Danger: Magnetism!
The appliance contains permanent magnets. They may affect electronic implants, e.g. pacemakers or insulin pumps.
Persons with electronic implants must stand at least 10 cm away from the appli-ance.

WARNING ‒ Risk of injury!
Parts that are accessible during installation may have sharp edges and may lead to cut-ting injuries.

• Wear protective gloves.
  Chemicals may be dangerous. When hand-ling chemicals, you must observe the re-commendations of the chemical producers.
• Wear personal protective equipment.

Hob and oven

Only use a hob and cooker from the same brand and with the same combination point.

• The green in the sticker on the hob’s power cord must match the green in the sticker on the oven. If this is not the case, order a suitable adapter from customer service. The article number for the ac-cessory is 744661.
  Fig. 1
  

Instructions for the electrical connection

In order to safely connect the appliance to the elec-trical system, observe the following instructions.

• Only an authorised expert or a specially trained service technician may connect the appliance. The person must be approved in accordance with the local regulations of the country and the electricity supply company.
• Connect the appliance to a fixed installation and set up appropriate isolating switches in accordance with the installation regulations.
• The manufacturer shall assume no liability for malfunctions or damage resulting from incorrect elec-trical wiring.

Connection type
The appliance corresponds to protection class 1.
You should therefore only use the appliance with a protective earth connection.

Information on fitted units

You can only install the induction hob above drawers or ovens with fan ventilation. Do not install refrigerators, dishwashers, non-ventilated ovens or washing machines below the hob.

Ensure that the fitted unit is heat-resistant up to at least 90 °C.

Worktop
Follow the worktop manufacturer’s recommenda-tions.

• Level, horizontal, stable.
• The worktop into which you are fitting the appliance must be able to withstand loads of approx. 60 kg.
• For thin worktops, use heat-resistant and moisture-resistant reinforcement material.
• Only check the evenness of the hob after it has been installed.

Extractor hood

• The clearance between the extractor hood and the hob must correspond at least to the clearance specified in the installation instructions for the ex-tractor hood.

Preparing the fitted units

1. Mark the unit cut-out in accordance with the installation diagram.
   ‒ Ensure that the angle of the cut surface to the worktop is 90°.
   → Fig. 2
2. After making the cut-outs, remove any shavings.
3. Seal the cut surfaces with heat-resistant material.
   

Ventilation
To guarantee that the appliance works correctly, the
hob must be sufficiently ventilated. The ventilation in
the lower section of the appliance requires a sufficient
supply of fresh air. Therefore, if required, adjust
the units for this purpose.

1. Maintain a minimum clearance between the rear of the unit and the kitchen wall.
   → Fig. 3
2. Ensure that an opening at the top of the rear of the unit is unobstructed.
   → Fig. 4
3. If the clearance from the back wall of the unit is less than 20 mm, create an opening on the underside.
   → Fig. 5
4. Do not hermetically seal the lower base.
   
   Note: If the appliance is installed in an island unit or in another location that is not described here, guarantee that the hob is ventilated appropriately.

Installation above an oven

• To ensure good ventilation, the clearance between the top of the worktop and the surface of the oven front must be 30 mm and the minimum clearance between the oven and hob must be 5 mm.
• If the clearance between the hob and the oven needs to be increased, refer to the installation instructions for the oven.
  → Fig. 6
  

Switching on the appliance
Requirement: Only connect the oven to the hob when the power supply is disconnected.

1. Position the hob in front of the cupboard.
2. Open the lid P on the lower part of the appliance using a tool and connect data cable S to the connection.
   → Fig. 7
3. Screw the protective earth conductor PE1 (green/ yellow) for the hob to the earthing point on the oven.
   ‒ Connect the PE1 conductor first and disconnect it last.
   → Fig. 8
4. Plug the poly box plastic plug into the oven.
   → Fig. 9
5. Tighten the screws on the poly box plug.
   → Fig. 10
6. Connect the S data line.
   → Fig. 11
7. Check that the appliance is ready for operation: If appears on the appliance’s display, the appliance is not connected correctly. Disconnect the appliance from the power supply and check the power cord connection at the mains supply.
   

Installing the support rails

Install the support rails in the unit.

• Glue the support rails to the stone worktop. Use a melt adhesive that is suitable for bonding metal and stone and has a temperature resistance of at least 90 °C.
• Do not use silicone for sealing.
• If mounting rails have already been attached, remove these and attach new ones.
• Use the lower threaded holes for tiled work surfaces.
  → Fig. 12
  

Inserting the hob

1. Insert the hob in the cut-out.
   → Fig. 13
2. Seal the tile joints on tiled work surfaces with silicone rubber.
   Note: Do not kink or trap the connection cable, and keep it away from sharp edges and hot parts.
   → Fig. 14
   

Removing the appliance

ATTENTION!
Tools may damage the appliance.
Never prise out the appliance from above.

1. Disconnect the appliance from the mains power supply.
2. Slide the oven out and place it in front of the unit.
3. Disconnect the S data line.
4. Loosen the screw on the poly box and pull out the poly box. Do not pull on the cables during the removal process.
5. Finally, disconnect the conductor from the earthing screw.
6. Push out the hob from below.

Documents / Resources

BOSCH HND679LS67 Built in Stove Set [pdf] Installation Guide 9001703689, 041001, HND679LS67 Built in Stove Set, HND679LS67, Built in Stove Set, Stove Set, Set

References

• User Manual