Mpow MBITS S User Manual BH481A

USER MANUAL

Mpow MBITS S

True Wireless Earbuds
Mpow MBITS S / BH481A

PACKING LIST

PACKING LIST

DIAGRAM

DIAGRAM

POWER ON

POWER ON
  1. The earphones automatically turn on (with blue LED light flashing) and start pairing when they are taken out from the charging case.
  2. In the shutdown status and when the earphones are not in the charging case, simultaneously press and hold the MFB of both earbuds for 2 seconds to power on ( with the blue LED light flashing).

POWER OFF

POWER OFF

PAIRING

PAIRING
  1. The earphones automatically start pairing (with the red and blue LED light flashing quickly on the right earbud) when they are taken out from the charging case, and choose “Mpow Mbits S” on your device.

2. Manually Switch to Pairing Mode:
When both earbuds are not in the charging case and in the state of power-off (keep pressing both MFB for 5 seconds to turn them off). Keep pressing both MFB for 4 seconds to re-enter into pairing mode in which LED flashes blue and red alternately. Finally, choose “Mpow Mbits S” on your device.

MUSIC

MUSIC

INCOMING CALL

INCOMING CALL

MUSIC & INCOMING CALL & Siri

Volume Up / Down
Volume + : press and hold the MFB button of Right earbud to turn up the volume increasingly.
Volume – : press and hold the MFB button of Left earbud to turn down the volume decreasingly.

Next / Previous Track
Next Track: double tap the MFB of Right earbud.
Previous Track: double tap the MFB of Left earbud.

Play / Pause
Tap the MFB of either earbud once.

Answer
Tap the MFB of either earbud once

Mute
When you are having a phone call, you can tap either earbud once to mute or unmute the earbud’s microphone

Hang Up
Double tap the MFB of either earbud.

Reject
Press and hold the MFB of either earbud for 1 second.

Activate Siri
Triple-tap the MFB of either earbud.

RESET

RESET

In the state of charging, simultaneously press and hold the MFB of both earbuds for 10 seconds. The LED light will flash blue, which means that the paired information is cleared successfully.

CHARGING

CHARGING

Do not put the earbuds in the charging case when the earbuds are wet.

CORRECT DISPOSAL OF THIS PRODUCT

( Waste Electrical& Electronic Equipment )

Disposal

This Marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.

To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household user should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contact. This product should not be mixed with other commercial wastes for disposal.

FCC STATEMENT

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.

Questions about your Manual? Post in the comments!

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. How do I get the 35 hours they advertise i don’t know to do this will someone please explain. Thank you

    Arthur Lieberman asks How do I get the 35 hours they advertise i don't know to do this will someone please explain. Thank you
    Manuals+ clarified question
    Question

    How do I achieve the advertised 35-hour battery life for the Mpow MBITS S earbuds?

    Answer

    The advertised 35-hour battery life for the Mpow MBITS S (BH481A) is a cumulative total achieved by using both the earbuds and the charging case together. It is not the duration of a single continuous charge for the earbuds alone.

    To maximize your battery performance, follow these steps:

    • Earbud Playtime: On a single full charge, the earbuds typically provide about 6 hours of playback.
    • Charging Case: The portable charging case holds multiple additional charges (approximately 4 to 5 full recharges), bringing the total combined time to 35 hours.
    • Recharging: When the earbuds run low, place them back into the charging case. Ensure the charging pins are clean and dry before inserting them.
    • Volume Levels: Note that battery life is often tested at 50% volume; using the earbuds at maximum volume or in extreme temperatures may reduce the total playtime.
  2. how can I download the manual?

    Susan McAvoy asks how can I download the manual?
    Manuals+ clarified question
    Question

    How can I download the Mpow MBITS S user manual?

    Answer

    To download the manual for your Mpow MBITS S (BH481A), please follow these steps:

    • Navigate to the bottom of the manual page on Manuals.plus.
    • Locate the section titled Download.
    • Click on the link labeled Mpow-MBITS-S-BH481A-Manual-Original or Mpow-MBITS-S-BH481A-Manual-Optimized.
    • The PDF will open in your browser; you can then use your browser's 'Save' or 'Download' icon to save it to your device.

    Alternatively, you can use the Deep Search tool on the site to find and download specific PDF files.

    1. save one of these files:
      https://manuals.plus/wp-content/uploads/2020/11/Mpow-MBITS-S-BH481A-Manual-Optimized.pdf
      https://manuals.plus/mpow/mpow-mbits-s-user-manual-bh481a.pdf

      admin asks save one of these files:
      https://manuals.plus/wp-content/uploads/2020/11/Mpow-MBITS-S-BH481A-Manual-Optimized.pdf
      https://manuals.plus/mpow/mpow-mbits-s-user-manual-bh481a.pdf
      Manuals+ clarified question
      Question

      How can I download the Mpow MBITS S user manual?

      Answer

      save one of these files:
      https://manuals.plus/wp-content/uploads/2020/11/Mpow-MBITS-S-BH481A-Manual-Optimized.pdf
      https://manuals.plus/mpow/mpow-mbits-s-user-manual-bh481a.pdf

  3. My right headphone will go on mute and off mute everytime I try to listen to something

    Zoe asks My right headphone will go on mute and off mute everytime I try to listen to something
    Manuals+ clarified question
    Question

    Why does my right Mpow MBITS S earbud keep muting and unmuting itself?

    Answer

    The Mpow MBITS S earbuds use a single tap on the Multi-Function Button (MFB) to control the mute function during calls and the Play/Pause function during music playback. If your right earbud is toggling mute or pausing on its own, it may be due to a sensitive touch sensor or a software synchronization error.

    To resolve this issue, please try a Factory Reset:

    1. Place both earbuds into the charging case.
    2. While the earbuds are charging, simultaneously press and hold the MFB of both earbuds for 10 seconds.
    3. The LED light will flash blue, indicating that the paired information has been cleared successfully.
    4. Remove the earbuds from the case and re-pair them with your device.

    Additionally, ensure the surface of the earbud is clean and dry, as moisture or debris on the MFB can cause ghost touches that trigger the mute/pause command.

  4. I have a Samsung Galaxy S7. I had the buds working well and they would automatically pair with my phone whenever I removed them from the case. I recently used another phone with them and paired them to that phone, when I misplaced my regular phone. But then I found my original phone again, but now I have to pair them again every time I take them out of the case to use them. Is it because the other phone’s connection is still enabled in the earphone’s pairing? Should I erase all connections and start over? I really love these headphones!

    Stewart McKinnon asks I have a Samsung Galaxy S7. I had the buds working well and they would automatically pair with my phone whenever I removed them from the case. I recently used another phone with them and paired them to that phone, when I misplaced my regular phone. But then I found my original phone again, but now I have to pair them again every time I take them out of the case to use them. Is it because the other phone's connection is still enabled in the earphone's pairing? Should I erase all connections and start over? I really love these headphones!
    Manuals+ clarified question
    Question

    How do I fix pairing issues with my Mpow MBITS S after using them with a different phone?

    Answer

    It is likely that your earbuds are still trying to connect to the second phone you used, or the pairing memory has become confused between the two devices. To restore the automatic pairing functionality with your Samsung Galaxy S7, you should perform a factory reset on the earbuds to clear all previous connection data.

    How to Reset your Mpow MBITS S:

    1. Place both earbuds back into the charging case.
    2. While the earbuds are in the charging state, simultaneously press and hold the MFB (Multi-Function Button) on both earbuds for 10 seconds.
    3. The LED light will flash blue, indicating that the paired information has been cleared successfully.

    After the reset:

    • Go to the Bluetooth settings on both your Samsung Galaxy S7 and the other phone you used. "Forget" or "Unpair" the Mpow Mbits S from both devices.
    • Turn off Bluetooth on the second phone to prevent it from interfering.
    • Take the earbuds out of the case; they will enter pairing mode automatically (red and blue lights flashing).
    • Select "Mpow Mbits S" on your Galaxy S7 to reconnect.

    Once this is done, they should resume automatically pairing with your S7 whenever you remove them from the case.

  5. MPOW MBITS S works fine with my android tablet but not with my IPhone. Phone asks me to turn on the unit and bring it in range, but the unit is on and close. Is there a compatibility issue with Apple?

    stephen zelnick asks MPOW MBITS S works fine with my android tablet but not with my IPhone. Phone asks me to turn on the unit and bring it in range, but the unit is on and close. Is there a compatibility issue with Apple?
    Manuals+ clarified question
    Question

    Why are my Mpow MBITS S earbuds not connecting to my iPhone even though they work with my Android tablet?

    Answer

    The Mpow MBITS S (BH481A) is compatible with Apple devices. The issue you are experiencing is likely because the earbuds are still actively connected to your Android tablet, which prevents them from entering pairing mode for a new device. Bluetooth earbuds typically only allow one active connection at a time.

    To resolve this and connect to your iPhone, please follow these steps:

    • Disconnect from Tablet: Turn off Bluetooth on your Android tablet or "Forget" the Mpow MBITS S in the tablet's Bluetooth settings.
    • Manual Pairing Mode: If the earbuds do not automatically enter pairing mode (indicated by red and blue lights flashing on the right earbud), turn them off by holding both MFB buttons for 5 seconds. Then, press and hold both MFB buttons for 4 seconds until the LED flashes blue and red alternately.
    • Reset the Earbuds: If the iPhone still cannot see the device, perform a factory reset:
      1. Place the earbuds in the charging case.
      2. While charging, press and hold the MFB buttons on both earbuds simultaneously for 10 seconds.
      3. The LED will flash blue to indicate the pairing history has been cleared.
      4. Try searching for "Mpow Mbits S" on your iPhone's Bluetooth menu again.
  6. I bought them recently, but the base does not charge …

    Le ho comprate da poco, ma la base non si carica…

    Mario asks <em>I bought them recently, but the base does not charge ...</em>

    Le ho comprate da poco, ma la base non si carica...

    Manuals+ clarified question
    Question

    Why is my Mpow MBITS S charging case not charging?

    Answer

    If your Mpow MBITS S charging case is not charging, please try the following troubleshooting steps:

    • Check the Connection: Ensure the USB charging cable is firmly plugged into both the charging case and a functional power source (such as a wall adapter or computer port).
    • Inspect for Debris: Check the charging port on the bottom of the case for any lint or debris that might be preventing a solid connection.
    • Try a Different Cable/Adapter: Use a different USB-C cable and a different power adapter to rule out a faulty cable or charger.
    • Reset the Device: While the manual primarily describes resetting the earbuds, you can try placing the earbuds in the case and, while in the charging state, simultaneously press and hold the MFB of both earbuds for 10 seconds until the LED flashes blue.
    • Dry the Components: Ensure the earbuds and the case are completely dry before attempting to charge, as moisture can interfere with the charging process.

    If the case still does not show any LED activity when plugged in after trying these steps, the unit may be defective. Since you mentioned buying them recently, it is recommended to contact the retailer or Mpow support for a warranty replacement.

  7. Used couple of months, but right side earbud suddenly has no responce (no sound).

    Chung asks Used couple of months, but right side earbud suddenly has no responce (no sound).
    Manuals+ clarified question
    Question

    Why is my right Mpow MBITS S earbud not responding or producing sound?

    Answer

    If your right Mpow MBITS S earbud has stopped responding, it may be due to a connection error or a charging issue. Please follow these troubleshooting steps to resolve the problem:

    • Perform a Factory Reset: This is the most effective way to fix synchronization issues.
      1. Place both earbuds back into the charging case.
      2. While the earbuds are in the state of charging, simultaneously press and hold the MFB (Multi-Function Button) of both earbuds for 10 seconds.
      3. The LED light will flash blue, indicating that the paired information has been cleared successfully.
      4. Remove the earbuds from the case and try pairing them with your device again.
    • Check for Power/Charging Issues: Ensure the charging pins on the right earbud and inside the charging case are clean and free of debris. If the earbud is not making a solid connection, it will not turn on.
    • Manual Power On: If the earbud doesn't turn on automatically when removed from the case, try turning it on manually by pressing and holding the MFB for 2 seconds.

    If the earbud still shows no LED activity or sound after a reset and cleaning, there may be a hardware failure.

  8. the volume of voice is so low people can hear me when i’m talking to them. i can hear them loud and clear and have checked the in call volume on the phone during a call. i’ve also attempted to turn it up on the earbud and that doesn’t help either.

    jarrett asks the volume of voice is so low people can hear me when i'm talking to them. i can hear them loud and clear and have checked the in call volume on the phone during a call. i've also attempted to turn it up on the earbud and that doesn't help either.
    Manuals+ clarified question
    Question

    Why is my microphone volume so low that others cannot hear me during calls on my Mpow MBITS S earbuds?

    Answer

    If others are having difficulty hearing you during calls with your Mpow MBITS S earbuds, please try the following troubleshooting steps:

    • Check the Mute Status: The Mpow MBITS S has a built-in mute function. During a call, tapping either earbud once will mute or unmute the microphone. Ensure you haven't accidentally enabled this feature.
    • Clean the Microphone Hole: Inspect the earbuds for any debris, dust, or earwax that might be blocking the microphone opening. Gently clean it with a soft, dry brush or a cotton swab.
    • Perform a Factory Reset: This can resolve software glitches affecting audio input. To reset:
      1. Place both earbuds back into the charging case.
      2. While they are charging, simultaneously press and hold the MFB (Multi-Function Button) on both earbuds for 10 seconds.
      3. The LED light will flash blue, indicating the paired information has been cleared.
      4. Delete "Mpow Mbits S" from your phone's Bluetooth settings and pair them again.
    • Check Microphone Permissions: If this happens only in specific apps (like Zoom or WhatsApp), ensure the app has permission to use the Bluetooth microphone in your phone's settings.
    • Positioning: Ensure the earbuds are seated correctly in your ears so the microphone is oriented toward your mouth as much as possible.
  9. My right earbud got fried and i do not know how to fix it any clue how

    Jordon Hendrick asks My right earbud got fried and i do not know how to fix it any clue how
    Manuals+ clarified question
    Question

    How can I fix my right Mpow MBITS S earbud if it is no longer working or appears to be 'fried'?

    Answer

    If your right earbud is unresponsive, you should first determine if it is a software synchronization issue or a hardware failure. Please try the following steps to reset and troubleshoot the device:

    • Perform a Factory Reset: Place both earbuds into the charging case. While they are charging, simultaneously press and hold the MFB (Multi-Function Button) on both earbuds for 10 seconds. The LED light should flash blue, indicating the pairing information has been cleared.
    • Check Charging Contacts: Ensure the charging pins inside the case and the contact points on the right earbud are clean and free of debris or moisture. If the earbud cannot charge, it will appear to be 'fried' or dead.
    • Manual Power On: If the earbud does not turn on automatically when removed from the case, press and hold the MFB on the right earbud for 2 seconds.

    Note: If the earbud has suffered actual electrical damage (e.g., from a power surge or water exposure), it cannot be repaired through settings. Since these units are sealed, hardware repairs are generally not possible. If the reset does not work, you may need to contact the retailer or Mpow support regarding a warranty replacement.

  10. Garbage – one of the buds does not work at all right out of the box. Never again, complete trash.

    jason asks Garbage - one of the buds does not work at all right out of the box. Never again, complete trash.
    Manuals+ clarified question
    Question

    How do I fix one Mpow MBITS S earbud that is not working?

    Answer

    If one of your Mpow MBITS S earbuds is not working out of the box, it may be due to a pairing desync or a charging issue. Please try the following troubleshooting steps:

    • Perform a Factory Reset: While the earbuds are in the charging case, simultaneously press and hold the MFB (Multi-Function Button) of both earbuds for 10 seconds. The LED light will flash blue to indicate the paired information has been cleared.
    • Check for Obstructions: Ensure there is no protective film covering the charging pins of the non-working earbud and that the pins in the case are clean.
    • Manual Power On: If the earbud didn't turn on automatically, press and hold its MFB for 2 seconds while it is out of the case.
    • Re-pair: After resetting, delete "Mpow Mbits S" from your Bluetooth settings and pair them again.

    If these steps do not resolve the issue, the unit may be hardware-defective, and you should contact the retailer for a replacement under warranty.

  11. My earbuds were working fine for years until one day u dropped them in the case, now I can’t get them to connect to each other. I can only connect one at a time no matter how many times I reset them.

    Todd asks My earbuds were working fine for years until one day u dropped them in the case, now I can't get them to connect to each other. I can only connect one at a time no matter how many times I reset them.
    Manuals+ clarified question
    Question

    How do I fix Mpow MBITS S earbuds that will not pair with each other and only connect individually?

    Answer

    It sounds like your earbuds have lost their TWS (True Wireless Stereo) synchronization. To fix this, you must perform a specific reset procedure while the earbuds are charging to clear the pairing memory and allow them to reconnect to each other.

    Follow these steps to reset your Mpow MBITS S:

    1. Go to your device's Bluetooth settings and "Forget" or delete "Mpow Mbits S" from the list of paired devices.
    2. Place both earbuds back into the charging case.
    3. While the earbuds are in the charging state, simultaneously press and hold the MFB (Multi-Function Button) on both earbuds for 10 seconds.
    4. The LED lights will flash blue, indicating that the paired information has been cleared successfully.
    5. Take both earbuds out of the case at the same time. They should enter pairing mode together (one earbud will flash red and blue quickly).
    6. Search for "Mpow Mbits S" on your device and reconnect.

    Note: Since the issue started after the earbuds were dropped, if the reset does not work, there may be internal hardware damage to the synchronization component.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.