TP-Link CPE710 Wireless Access Point User Guide

TP-Link

TP-Link CPE710 Wireless Access Point

TP-Link-CPE710-Wireless-Access-Point-Imgg

Loading PDF…
Download PDF

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. CPE710のSSIDで別のCPE710を中継機として使いたいのですがうまく接続できません。

    サンエー井岡 asks CPE710のSSIDで別のCPE710を中継機として使いたいのですがうまく接続できません。
    Manuals+ clarified question
    Question

    How do I connect a second CPE710 as a repeater to an existing CPE710 SSID?

    Answer

    To connect a second CPE710 as a repeater (Client or Bridge mode) to your primary CPE710, please follow these steps within the PharOS web interface:

    • Check Operation Mode: Ensure the primary CPE710 is set to Access Point mode and the second unit is set to Client or Bridge mode. The CPE710 does not have a dedicated 'Repeater' mode in the traditional sense; 'Bridge' mode is typically used for this purpose.
    • Alignment: Since the CPE710 is a highly directional 23dBi antenna, the units must be precisely pointed at each other. Even a slight misalignment can prevent a successful connection.
    • Frequency Settings: Ensure both devices are using the same Channel Width (e.g., 20/40/80MHz). If the primary unit is set to a specific frequency, the secondary unit must be able to scan and find that frequency.
    • Security Match: The WPA2/PSK password and encryption type on the secondary unit must exactly match the settings on the primary Access Point.
    • IP Address Conflict: Ensure both units have unique static IP addresses on the same subnet (e.g., 192.168.0.254 and 192.168.0.253) so you can manage them independently.

    If you still cannot connect, try performing a Survey on the secondary unit's Wireless settings page to see if the primary SSID appears in the list of available networks.

  2. CPEシリーズアンテナを利用して、NEC製監視装置CSDX(またはCSDJ)の監視をPCにて閲覧することは可能でしょうか。

    渡邉 拓夢 asks CPEシリーズアンテナを利用して、NEC製監視装置CSDX(またはCSDJ)の監視をPCにて閲覧することは可能でしょうか。
    Manuals+ clarified question
    Question

    Is it possible to use the TP-Link CPE series antennas to view monitoring data from NEC monitoring devices (CSDX or CSDJ) on a PC?

    Answer

    Yes, it is generally possible to use the TP-Link CPE710 (or other CPE series devices) to transmit data from NEC monitoring devices like the CSDX or CSDJ to a PC, provided both devices support standard Ethernet/IP networking.

    The CPE710 acts as a high-speed wireless bridge. To achieve this, you would typically follow these steps:

    • Network Connection: Connect the NEC monitoring device to one CPE unit (configured as an Access Point) and the PC (or the network the PC is on) to a second CPE unit (configured as a Client).
    • Transparent Bridge: The CPE series creates a transparent Layer 2 bridge, meaning the NEC device and the PC will behave as if they are connected by a physical Ethernet cable.
    • IP Configuration: Ensure that the NEC device, the CPE units, and the PC are all within the same IP subnet so they can communicate.
    • Software: You will still need the specific NEC monitoring software installed on your PC to view the data; the CPE units only provide the wireless link.

    Note: Since the CPE710 is a highly directional 5GHz antenna, a clear line-of-sight between the two antennas is required for a stable connection.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.