Power magnetic GPS Tracker Manual
Preface
LK209
Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly.Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual. Any change will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.
FCC RF Exposure Information and Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
1. Summary
Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any
remote targets by SMS or internet. The most advanced technology of GPS and AGPS dual positioning.
2. Applications
1. Vehicle rental / Fleet management etc
2.Container/cargo/asset tracking
3.Hardware Description
4. Content Specs.
5.Userage:
5.1 SIM card installation
1.Open the rubber plug
2.Insert the GSM SIM card.
3.close the rubber plug.
5.2 Battery and Charger
Do charge the battery to capacity in 8 -12 hours for first time. Please use the battery and charger provided bythe manufacturer. This unit adopts built-in Li-ion battery, and full battery can standby 120days. After first use, the battery usually should be charged fully in 5–8 hours.
Cautions:
a: For it’s Li-ion battery, which contains harmful chemicals and may burst, please don’t bump, puncture it violently and keep it off fire.
b: Please charge the battery in time to keep it working normally.
5.3 Startup
– Put the SIM card and battery in place.
– Turn on the unit outdoors by Pushing the button to“On”the indicator is on.
– Set admin number,APN , IP and open GPRS
Eg: Step1.admin123456+space+your phone number
Step2.apn123456+ space+local apn content
Step3.adminip123456+space+101.1.16.228+space+7700
Step4. gprs123456
– In 10 or 40 seconds, the unit will begin to work and acquire the GSM signals as well as the GPS signals. The indicator will keep flashing every 3 seconds when the unit has received the signals.
– When this unit receives GPS signals normally, you can use it and do any setting as the instructions of this manual.
1.Google link: click link, there is map when positioning ok,
no map means no positioning.
2.V:A GPS signal ok.V:V no GPS signal
3.2013-08-30 20:54:15: the last time receive GPS signal.
4.Spd:000km/h: the speed of tracker ran.
5.Bat:6 battery balance（the range is from 1 to 9）
6.ID:4102000759: ID code of device(used for connect
tracking website or APP)
7.S19G04；plmn：46001 GSM operator data
8.Lac：9516，cellid:23596 LBS data
5.4Change the password
5.4.1 Set Password: Send sms: “password+old password+space+new password” to the unit to change the password.Status of indicator Meaning Red led on all the time Charging red led off Full battery or charged full For Example, pls send sms: “ password123456 000000” to terminal device, it will reply sms: “password OK”. New password 000000 changed in success.
5.4.2 Be sure keep the new password in mind, you have to upload the software to restore the original setting in case of losing the new password.
5.4.3 Make sure the new password is in 6 digits Arabic numbers, or the tracker can not recognize the password.
5.4.4 Make sure that all the symbol“+”in sms commends is just for quick understanding, which don’t need to enter “+” in sms, and “space” means press the spacebar button of the cell phone.
5.5Authorization
5.5.1 Send SMS：“ admin+password+space+cell phone number” to set up a authorized number. The other authorized numbers should be set by the first authorized number. If the number is successfully authorized, the unit will reply “admin ok!” in SMS.
5.5.2 Send SMS：“ noadmin+password+space+authorized number” to delete the authorized number.
5.5.5 When the authorized number call the device, it will hang up your phone and reply a realtime latitude and longitude information, as below:
5.6Single Locating
5.6.1 If there is no authorized number, when any number dials up the unit, it will report a Geoinfo; If there is already an authorized number, then it will not respond when an unauthorized
number calls it up.
5.6.2 Single message inquires the latitude and longitude information, any telephone number can send instruction “where” to the equipment, then the equipment will reply the latitude and longitude informati on to this telephone.
5.6.3 When an authorized number dials up the unit, it will hang up and report a real-time Geoinfo as below:
*Tracking location, When GPS signals is weak, the position of latitude and longitude included in the SMS is the position that the tracker received GPS signals at last. If it is different with its exact current location, pay attention to check the time included in the SMS you got.
5.7Auto Track
5.7.1 Send SMS command “t030s005n+password” to the tracker device, it will report the “no reply” at 30s intervals for 5 times. (s:second, m:minute, h:hour). This command setting must be
in 3 digits and the maximum value is 255.
5.7.2 Unlimited times auto track: Send SMS “t030s***n+password” to the tracker device, it will reply the “no reply” continuously at 30 seconds intervals.
5.7.3 Cancellation: Send SMS “notn+password” to the tracker device, it will report the “notn ok”.
Note: the interval must not less than 20s.
5.8 Monitor (Voice Surveillance)
5.8.1 The command to switch between Track and Monitor are “tracker” and “ monitor”.
5.8.2 The default mode is “track” (Track mode).
5.8.3 Send SMS “monitor+password” to the unit, and it will reply “monitor ok!” and switch to “monitor” mode.
5.8.4 Send SMS “tracker+password” to the unit, it will reply “tracker ok!” and restore to “track” mode.
5.9Geo-fence
Set up a geo-fence for the unit to restrict its movements within a district. The unit will send the message to the authorized numbers when it breaches the district.
5.9.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can Send SMS: “stockade+password+space+latitude,longitude; latitude,longitude” to unit to set the restricted district.
Remark: The first latitude&longitude is coordinate of the top left corner of the Geo-fence, while the second latitude&longitude is the coordinate of the bottom right corner.
5.9.2 Cancel: Send SMS:” nostockade+password” to deactivate this function,tracker will reply “nostockade ok”
5.10Movement alert
5.10.1 Set up: When the unit stays immobile in a place for 3-10 minutes, the user can send SMS: “move+password” to the unit, then the unit will reply “move ok!”. In case of such a movement
（the unit default distance is 500M）, it will send SMS “Move ALARM+ Latitude and longitude” to the authorized number
5.10.2 Cancel: Send SMS:” nomove+password” to deactivate the movement alert, tracker will reply “nomove ok”.
5.11 Overspeed alert:
5.11.1 Set up: Send SMS: “speed+password+space+080” to the unit (suppose the speed is
80km/h), and it will reply “speed ok!”. When the target moves exceeding 80 km/h, the unit will
send SMS :”speed ALARM !+ Latitude and longitude” to the authorized numbers every 5
minutes.
5.11.2 Cancel: Send SMS “nospeed+password” to deactivate the overspeed alarm, tracker will reply “nospeed ok”.
Remark: The recommended speed should be not less than 50km/h. For below that rate, it will be
effected the accuracy by gps signals drift etc.
5.12Low battery alert
When GPS device battery is going to be about 3.7V, it will send SMS: “bat:l” at 30 minutes interval.
5.13Terminal (local) Time Setting
Send SMS “time+space+zone+password+space+local time”.
For example, Send SMS “time zone123456 8” (time zone of China).
If the local time zone is negative as “-3”, then it should set as SMS: “time zone123456 -3”.
5.14Sleeping power-save mode
On normal status, when the unit stoped over 10minutes, it will change to sleeping mode, on this mode, the power consumption is 4mah/h only. When it get any command or been moved, it will start GPS locating automatically. Forced sleeping mode, Setting: Send SMS “sleep+password”, the unit will reply “sleep ok”, it enter to forced sleeping power-save mode. Start device, send SMS “nosleep+password”,the unit will reply “nosleep ok”, it start GPRS
5.17 Shock alert
Note: It is effective sending by authorized number
Send SMS command“shock+password”, the unit will reply “shock ok.”
Cancel: Send SMS command “noshock+password”, the unit will reply “noshock ok.”
5.15Restore factory settings
Note: It is effective sending by authorized number Send SMS command “format”, the unit will reply “The tracher will immediateiy restore the factory settings.All previous settings will be canceled.”
or
Send “begin+password” in SMS to the unit, it will reply “begin ok” and initialize all the settings. (Default password: 123456) For example, send SMS“ begin123456” to the tracker via a cell phone, If succeeded, it will reply“begin ok”.
5.16 GPRS setting
User must send SMS via cell phone to set up IP, port and APN before starting GPRS.
5.16.1 Setting up APN
5.16.1.1 APN standards for Access Point Name and differs from country to country. For more
information about the local APN, inquire with your local GPRS network operator.
5.16.1.2 Text the tracker a SMS “apn+password + Space + your local APN” via a cell phone
and if succeeded in setup, the tracker will return the message “apn ok”.
5.16.1.3 e.g. send SMS command “apn123456 cmnet”. If succeeded, “apn ok” is returned by
the tracker in SMS.
Notes: 123456 refer to password of tracker and CMNET is the APN of China Mobile (One of
GSM Operator in china).
5.16.1.4 Set IP Send SMS command：adminip123456 101.1.16.228 7700 If succeeded,
“adminip ok”
5.16.1.5 Dropped Alarm
When device have been attached on metal 15 sec after ( the Dropped button have been pressed 15 sec ) ,if it device was dropped , it would alarm to the admin number by SMS or calling .
6.command list(pls note 123456 is the default password) .
7. Web platform and sever ip&port
Website Sever IP Port
www.lkgps.net 101.1.16.228 7700
8.App download
8.1 android version: scan below QR code
8.2 ios version: search “LKGPS” in app store
9. Faults & The solutions
https://fccid.io/2AI9PLK209/User-Manual/Users-Manual-3082858.pdf
References
- User Manualmanual.tools
How to install app on my computer
How do I install the LKGPS app on my computer?
The LKGPS LK209 tracker does not have a dedicated desktop application for installation on a computer. Instead, you can monitor your device on a computer using the web-based tracking platform.
To access your tracker from a computer:
123456).If you specifically need an app, the manufacturer only provides mobile versions for Android (via QR code in the manual) and iOS (by searching "LKGPS" in the Apple App Store). For computer use, the web platform is the intended method.
Read the full Q&A page
How do I put multiple units on app. i have 3 units for 3 vehicles
How do I add multiple LK209 GPS tracker units to the LKGPS app?
To manage multiple LK209 units on the LKGPS app or web platform, you typically need to create a "User Account" (also known as a fleet or group account) rather than logging in with an individual device ID. Here is how to proceed:
www.lkgps.netand provide them with the ID numbers of all three units. They can then link these IDs to a single username and password.http://www.lkgps.netand logging in with your user account.If you are setting these up for the first time, ensure each unit has been initialized with the GPRS commands mentioned in the manual (Step 5.3), specifically setting the APN and the admin IP (
adminip123456 101.1.16.228 7700) so they can communicate with the server.Read the full Q&A page
how to create an account in lkgps?so that i connect all my device in 1 application?
How do I create an account in the LKGPS app to connect multiple devices?
To connect and manage multiple LKGPS LK209 devices under one account, you typically use the device's unique ID code for the initial login. Follow these steps based on the manual:
ID:4102000759). This ID is used to connect to the tracking website or app.123456), managing multiple devices usually requires a "User Account" rather than an "ID Login." If the app does not provide a direct 'Sign Up' button for a master account, you may need to contact your dealer or the platform administrator to create a username and group all your device IDs under that single account.Note: Before the app can track the device, ensure you have configured the GPRS settings by sending the following SMS commands to the tracker's SIM card:
adminip123456 101.1.16.228 7700andgprs123456.Read the full Q&A page
Hello,
I have installed the LKGPS in my Car, but I can’t track it in the application, it show logged off, can you please instruct me to make it log in or unable.
I have installed the LKGPS in my Car, but I can't track it in the application, it show logged off, can you please instruct me to make it log in or unable.
How do I fix the 'logged off' status in the LKGPS application for my LK209 tracker?
If your LK209 GPS tracker shows as "logged off" in the application, it usually means the device has not successfully established a GPRS data connection with the server. To fix this, you must configure the APN (Access Point Name) and enable GPRS via SMS commands.
Follow these steps using your mobile phone to send SMS commands to the SIM card number inside the tracker (the default password is 123456):
admin123456 [your phone number](e.g.,admin123456 1234567890).apn123456 [local apn](e.g.,apn123456 internet).adminip123456 101.1.16.228 7700.gprs123456.Additional Troubleshooting:
nosleep123456.Read the full Q&A page
Hello. Have I got this error fixed? Can you tell me – ??
Здравствуйте. У меня ьоже такой устранили ошибку? Можете мне подсказать-??
How to remove the Vehicle picture.
If set, it shows “BIG square picture” on website and only part of info is vssable.
I can change it via top left panel “Target” secion, but even I set 1×1 size – shows BIG.
HOW TO REMOVE IT???
If set, it shows "BIG square picture" on website and only part of info is vssable.
I can change it via top left panel "Target" secion, but even I set 1x1 size - shows BIG.
HOW TO REMOVE IT???
How do I remove or resize the vehicle picture on the LKGPS tracking website?
The LKGPS LK209 manual focuses primarily on SMS commands and hardware setup, and does not provide specific instructions for managing UI elements like vehicle images on the web platform (www.lkgps.net).
Based on your description of the "Target" section in the top-left panel, here are some troubleshooting steps to try on the website:
www.lkgps.netis managed by the manufacturer's server, if the "Target" panel settings are not applying correctly, it may be a server-side display bug that requires their technical support to reset your profile.Read the full Q&A page
By SMS it works but the applications tell me: LK209C not activated
I see that I am not the only one having this problem.
It seems well activated since it is responding to text messages.
OTHERWISE, is there a command to send to activate it?
Par SMS ça fonctionne mais les applications me disent : LK209C non activé
Je vois que je ne suis pas le seul à avoir ce problème.
Il paraît bien activé puisqu’il répond aux SMS.
SINON y a t il une commande à envoyer pour l’activer ?
I see that I am not the only one having this problem.
It seems well activated since it is responding to text messages.
OTHERWISE, is there a command to send to activate it?</em>
Par SMS ça fonctionne mais les applications me disent : LK209C non activé
Je vois que je ne suis pas le seul à avoir ce problème.
Il paraît bien activé puisqu'il répond aux SMS.
SINON y a t il une commande à envoyer pour l'activer ?
How do I activate the LK209C GPS tracker for use with the mobile application when it only responds to SMS?
If your LK209C tracker responds to SMS but appears as "not activated" in the app, it usually means the GPRS data connection has not been initialized. To activate the device for the application, you must send a series of SMS commands to configure the APN (Access Point Name) and the server connection.
Follow these steps (assuming the default password is 123456):
apn123456 [your_local_apn]. Replace[your_local_apn]with the APN provided by your SIM card carrier (e.g., apn123456 cmnet). The device should reply "apn ok".adminip123456 101.1.16.228 7700. The device should reply "adminip ok".gprs123456. This command triggers the data connection required for the app to see the device online.Once these commands are sent, ensure the device is outdoors with a clear view of the sky. It may take a few minutes for the status in the LKGPS app to update from "not activated" to "online". If it still fails, verify that your SIM card has an active data plan and that the PIN code is disabled.
Read the full Q&A page
How you get it to go back online ran out of credit now i toped up still says ofline i toped up after a week or two
How do I get my LK209 GPS tracker back online after topping up the SIM card credit?
When a GPS tracker remains offline after a credit top-up, it often needs to re-establish its GPRS connection. Follow these steps to bring your LK209 back online:
gprs123456(replace 123456 with your password if changed) to the device. This forces the unit to start the GPRS service.apn123456 [your_local_apn](e.g.,apn123456 cmnet). You can find your specific APN by contacting your SIM card provider.nosleep123456to ensure it is active.begin123456. Note: This will reset settings to factory defaults.If the device still shows as offline in the app or web platform, try sending the command
G123456#orwhereto see if the device replies with a location via SMS. If it replies via SMS but is offline in the app, the issue is specifically with the GPRS/APN settings.Read the full Q&A page
Hi Sir/Mam,
Please send features and functions for LKGPS2.
Thanks,
Please send features and functions for LKGPS2.
Thanks,
What are the features and functions of the LKGPS LK209 tracker?
The LKGPS LK209 is a magnetic GPS tracker that utilizes GSM/GPRS networks and GPS/AGPS dual positioning. Its primary features and functions include:
Note: While you mentioned 'LKGPS2', these features apply to the LK209 model covered in this manual. If your device is a different specific version, some commands may vary.
To view the full command list and setup instructions, please refer to the LK209 User Manual.
Read the full Q&A page
Hello, the device makes 1 call at a time to my number, how can you deactivate that? Thank you
Buenas el dispositivo realiza 1 llamada a cada rato a mi numero como se puede desactivar eso? Gracias
Buenas el dispositivo realiza 1 llamada a cada rato a mi numero como se puede desactivar eso? Gracias
How do I stop the LK209 GPS tracker from calling my phone number repeatedly?
The LK209 GPS tracker may be calling your number due to active alarm settings such as the Dropped Alarm, Movement Alert, or Shock Alert. To stop these calls, you can try deactivating these specific features by sending the following SMS commands to the tracker (assuming the default password is
123456):nomove123456. This stops the device from alerting you when it detects movement.noshock123456. This stops alerts triggered by vibrations or impacts.nospeed123456.nostockade123456.If you are unsure which alarm is triggered, you can perform a full reset to factory settings by sending the command
begin123456. This will initialize all settings and should stop the automated calls, though you will need to re-configure your admin number and GPRS settings afterward.Read the full Q&A page
My lkgps2 is constantly with green light on and does not work, what should I do?
Meu lkgps2 fica co stantemente com Luz verde acesa e não funciona, o que devo fazer?
Meu lkgps2 fica co stantemente com Luz verde acesa e não funciona, o que devo fazer?
Why is the green light on my LKGPS LK209 tracker constantly on and the device not working?
According to the LKGPS LK209 manual, the behavior of the indicator light is a key diagnostic tool. A constant light usually indicates the device is searching for a signal or initializing.
begin123456(where 123456 is the default password) to the tracker's phone number.If the light never transitions to a flash every 3 seconds even when outdoors, there may be an issue with the SIM card compatibility or the local GSM network coverage.
Read the full Q&A page
If I forgot the password from the device, how can I recover it?
Если забыл пароль от устройства, как можно восстановить?
Если забыл пароль от устройства, как можно восстановить?
How can I recover or reset my password if I have forgotten it?
According to the LKGPS LK209 manual, if you have forgotten your custom password, you must upload the software to restore the original settings. The manual notes that you should keep your new password in mind because this recovery process is required to revert to the default state.
If you have not yet changed the password, the default password for the device is
123456.If you still have access via an authorized admin number, you can try to reset the device to factory settings by sending the SMS command:
formatorbegin123456(using the default password). If successful, the unit will reply "begin ok" and all settings, including the password, will be initialized to factory defaults.Read the full Q&A page
Everything works except the supposedly busy call ……
How to fix it ??
Alles funktioniert ausser das anrufen angeblich besetzt……
Wie kann man es beheben ??
I cannot track it in the app, it shows as disabled, can you please instruct me to log in or not.
Я не могу отследить его в приложении, он отображается как отключенный, не могли бы вы проинструктировать меня, чтобы он входил в систему или не может.
Я не могу отследить его в приложении, он отображается как отключенный, не могли бы вы проинструктировать меня, чтобы он входил в систему или не может.
How do I fix the LK209 GPS tracker showing as disabled in the app and how do I log in?
If your LK209 GPS tracker shows as "disabled" or offline in the app, it usually means the GPRS data connection has not been properly configured or the device is in sleep mode. Follow these steps to get the device online:
www.lkgps.net, use the ID code found on the device sticker as the username and the default password123456.apn123456 [your_local_apn](replace[your_local_apn]with the APN provided by your mobile carrier).adminip123456 101.1.16.228 7700.gprs123456to activate data transmission.nosleep123456to wake it up and force GPRS to stay active.Read the full Q&A page
My unit is fully charged but is offline…..why?
Why is my LK209 GPS tracker showing as offline even though it is fully charged?
If your LK209 unit is charged but showing as offline, it is likely failing to connect to the GSM network or GPRS data service. Please check the following steps to bring it back online:
gprs123456(replace 123456 with your password if changed) to the tracker.apn123456 [your local APN]. For example, if using China Mobile, you would sendapn123456 cmnet.adminip123456 101.1.16.228 7700.You can verify the current status by calling the device; if it hangs up and sends you a Google Maps link via SMS, the GSM portion is working, and the issue is strictly with your GPRS/APN settings.
Read the full Q&A page
My gps tells me that it expired, it no longer lets me see the location of the vehicle, what can I do to configure it again? The chip has a balance
me dice mi gps que expiro ya no me deja ver la ubicacion del vehiculo que puedo hacer para configurarla de nuevo el chip tiene saldo
me dice mi gps que expiro ya no me deja ver la ubicacion del vehiculo que puedo hacer para configurarla de nuevo el chip tiene saldo
How do I reconfigure my LK209 GPS tracker if it says it has expired and no longer shows the location?
If your LK209 GPS tracker is reporting as "expired" on the app or web platform, it usually refers to the service subscription for the tracking platform (www.lkgps.net) rather than the SIM card balance. However, you can still verify and reconfigure the device's connection by following these steps:
GPRS123456(where 123456 is the default password) to the tracker.apn123456 [your_local_apn]. For example, if using China Mobile, you would sendapn123456 cmnet.adminip123456 101.1.16.228 7700.whereto the device. If it replies with a Google Maps link and the coordinates are current, the hardware is working, and the "expired" message is strictly related to your software account.If you wish to start over completely, you can restore factory settings by sending the SMS command:
begin123456.Read the full Q&A page
When I send a message apn 123456 the reply is apn sms passwprd error how to fix it
How do I fix the 'apn sms password error' when setting up my LK209 GPS tracker?
The "apn sms password error" typically occurs because of a formatting mistake in the SMS command. To fix this, please ensure you are following these specific rules from the manual:
apn123456 [space] your_local_apn. For example:apn123456 cmnet.begin123456(this will restore the default password to 123456).If you continue to receive an error, double-check with your mobile provider that you have the correct APN name for your specific SIM card.
Read the full Q&A page
My phone has been in normal use since the beginning of May 2021, but recently it has been showing “arrears” and the device is offline, but the monthly calling card I used has no problems and has very substantial data available. What should I do?
email: gg546@outlook.com
Mr.CHAN
我的由2021年5月初一直都正常使用，但近日一直顯示「欠費」，設備離線，但我用的月費電話卡並無任何問題，有非常充實可用數據，請問應該如何處理？
email: gg546@outlook.com
Mr.CHAN
email: gg546@outlook.com
Mr.CHAN<e/em>
我的由2021年5月初一直都正常使用，但近日一直顯示「欠費」，設備離線，但我用的月費電話卡並無任何問題，有非常充實可用數據，請問應該如何處理？
email: gg546@outlook.com
Mr.CHAN
Why is my LK209 GPS tracker showing 'arrears' and appearing offline even though my SIM card has data and credit?
The "arrears" message typically indicates that the tracking platform (app or website) believes the service subscription for that specific device ID has expired, which is separate from your SIM card's data plan. Here are the steps to troubleshoot and resolve the offline status:
www.lkgps.net) or the LKGPS app. The "arrears" status usually refers to the renewal fee for the tracking service itself. You may need to contact your vendor to renew the device's service life.gprs123456(assuming 123456 is your password).apn123456 [your_local_apn]. For example, if your provider's APN is 'internet', sendapn123456 internet.adminip123456 101.1.16.228 7700.If the SIM card is definitely active and the APN is set, the "arrears" message is almost certainly a platform-side expiration that requires renewal through the seller or the LKGPS service provider.
Read the full Q&A page
Very complicated to set up and use,responds to some texts and not to others
How do I troubleshoot setup issues and inconsistent SMS responses with the LK209 GPS tracker?
If your LK209 GPS tracker is responding inconsistently to text messages, it is often due to authorization settings or incorrect command formatting. Follow these steps to ensure the device is set up correctly:
admin123456 [your phone number](replace 123456 with your password if changed).admin123456 1234567890rather thanadmin123456+1234567890.begin123456. This will initialize all settings to default.For GPRS/App tracking, remember you must also configure the APN by sending:
apn123456 [local apn name].Read the full Q&A page
I have the same problem of not being able to track the gps in the application. Additionally, the GPRS appears turned off, and I have not been able to solve it. Can someone help me please ?
Tengo el mismo problema de no poder rastrear el gps en aplicación. Adicionalmente, el GPRS me aparece apagado, y no he podido solucionarlo. Alguien me puede ayudar por favor ?
Tengo el mismo problema de no poder rastrear el gps en aplicación. Adicionalmente, el GPRS me aparece apagado, y no he podido solucionarlo. Alguien me puede ayudar por favor ?
How do I enable GPRS and fix tracking issues in the LKGPS application?
To enable GPRS and ensure your LK209 tracker connects to the application, you must configure the APN, IP, and GPRS settings via SMS commands. Please follow these steps using your mobile phone to send messages to the SIM card number inside the tracker:
apn123456 [your local APN](Replace '[your local APN]' with the APN provided by your SIM card carrier, e.g.,apn123456 cmnet). The device should reply "apn ok".adminip123456 101.1.16.228 7700. The device should reply "adminip ok".gprs123456. This command activates the data connection required for the app.nosleep123456to ensure the device stays active.Note: Ensure the SIM card has an active data plan, is not locked by a PIN code, and that the device is outdoors to acquire a GPS signal. Once configured, use the ID code on the device label to log into the LKGPS app or www.lkgps.net.
Read the full Q&A page
yes hi ever time i send the command to my tracker gprs123456 it reply’s back g:sms password error my tracker is always offline with no gps signal and this this the problem i don’t know what it is trying to tell me and how i can solve the problem if someone has the solution to my problem thank you
Why am I receiving an 'sms password error' when sending the gprs123456 command, and why is my LK209 tracker offline with no GPS signal?
The "sms password error" indicates that the tracker does not recognize "123456" as the current password. This can happen if the password was changed or if the command format is incorrect. Additionally, the device being offline with no signal suggests it hasn't successfully connected to the GPRS network or acquired a satellite fix.
To resolve the password error:
gprs123456).format(note: this usually requires being sent from an authorized admin number). Alternatively, try sendingbegin123456to initialize the settings.To resolve the 'Offline/No Signal' issue:
apn123456 [space] [your local APN name].adminip123456 101.1.16.228 7700.Read the full Q&A page
i have use the app and deleted it how do i get back my account and password to get the gps device to work again on the app
How do I recover my account and password for the LKGPS app after deleting it?
To regain access to your LKGPS device on the app, you will need your device's unique ID and the password. Please follow these steps:
whereto the phone number of the SIM card inside the tracker; the device should reply with a message containing its 10-digit ID.123456.begin123456(replace 123456 with the default if that was not it) orformatto the device. This will restore the default password to123456.If you are unable to log in because the account was tied to a specific username you created rather than the ID, you may need to contact the seller or the platform administrator at www.lkgps.net to have your account or password manually reset.
Read the full Q&A page
Can I get a history log of a certain trip to print out of view on screen?
How can I view or print the trip history log for the LK209 GPS tracker?
Yes, you can view the history log of your trips using the tracking platform or mobile application. While the physical manual focuses on SMS commands for real-time tracking, historical data is managed through the following digital interfaces:
To ensure history is being recorded, verify that GPRS is active by sending the SMS command
gprs123456to the device (assuming 123456 is your password) and that your APN and Admin IP (101.1.16.228) are correctly configured as per section 5.16 of the manual.Read the full Q&A page
Can I get a history log of a certain trip to print out or view on screen?
How can I view or print a trip history log for the LK209 GPS tracker?
Yes, you can view your trip history through the LKGPS web platform or mobile application. While the physical device primarily communicates real-time data via SMS, historical logs are stored on the server when GPRS is enabled.
Note: For history to be recorded, your device must have GPRS active. Ensure you have set the APN and GPRS mode by sending the following SMS commands to the tracker:
1.
apn123456 [your local APN]2.
gprs123456Read the full Q&A page
Why is there no reply when I send where to the transmitter? Are you out of battery?
発信器にwhereと送っても返信がないのは何が原因ですか？電池切れですか？
発信器にwhereと送っても返信がないのは何が原因ですか？電池切れですか？
Why is there no reply when I send the 'where' command to the LK209 GPS tracker? Is the battery dead?
There are several reasons why your LK209 GPS tracker might not be replying to the
wherecommand:bat:lSMS alert when the battery drops to approximately 3.7V.Recommendation: Try calling the device. If it is powered on and has a signal, it should hang up and reply with a Google Maps link. If it goes straight to voicemail, the device is likely powered off or out of signal range.
Read the full Q&A page
Что означает drop alarm?
What does 'drop alarm' mean?
The Drop Alarm (also referred to as 'Dropped Alarm' in the manual) is a security feature designed to alert you if the tracker is removed or falls off the object it is attached to.
According to the manual:
Read the full Q&A page
The problem is that the app stops all the time, I reinstalled it, but it still stops. What can be done in this case?
Az a baj az app állandóan leáll , újra telepitettem , de akkor is leáll . Mit lehet tenni ilyenkor ?
Az a baj az app állandóan leáll , újra telepitettem , de akkor is leáll . Mit lehet tenni ilyenkor ?
What should I do if the LKGPS app keeps crashing even after reinstalling it?
If the LKGPS application continues to crash after a reinstallation, you can try the following troubleshooting steps to resolve the issue:
If the problem persists, it may be a temporary server-side issue or a bug with the specific app version on your hardware. Using the website is the most reliable alternative during app downtime.
Read the full Q&A page
Is there a way to reset my password? I forgot my password while I was not using my device.
パスワードのリセット方法はありますか？端末を使っていない間にパスワードを忘れてしまいました。
パスワードのリセット方法はありますか？端末を使っていない間にパスワードを忘れてしまいました。
How do I reset my password if I have forgotten it?
According to the LK209 user manual, if you have forgotten your custom password, you must upload the software to restore the original settings. This typically requires contacting the manufacturer or your dealer for technical assistance, as it is not a simple SMS command.
However, if you are trying to return the device to its factory state and the password has not been changed from the default, you can try the following:
123456.begin123456to the tracker. If successful, it will reply "begin ok" and reset all settings.formatfrom an authorized admin number to restore factory settings.Note: If you changed the password and forgot it, the manual states that software re-uploading is the only way to restore access.
Read the full Q&A page
How to display multiple devices simultaneously with one app
How should I set it?
１アプリで複数台同時表示するには
どのように設定すればよいのでしょうか
How should I set it?
１アプリで複数台同時表示するには
どのように設定すればよいのでしょうか
How can I display multiple LK209 GPS trackers simultaneously in one app?
To display multiple LK209 devices simultaneously in the LKGPS app, you generally need to log in using a User Account rather than an individual Device ID. Here is how to set this up:
If you are using the web platform at
www.lkgps.net, the process is the same; use the "Account" login option instead of "ID" to manage your fleet.Read the full Q&A page