LeonLite LED Motion Security Light User Manual

LeonLite LED Motion Security Light - logo

LED Motion Security Light
User Manua’
READ ALL WARNINGS AND INSTRUCTIONS BEFORE INSTALLING THIS
PRODUCT TO ENSURE SAFETY AND PROPER OPERATION, KEEP THIS
MANUAL GUIDE FOR FUTURE REFERENCE

WARNING

  • Failure to install and wire fixture in accordance with the National Electrical Codes (NEC), all applicable Federal, State, and Local electrical codes, as well as specific U.L. safety standards for the intended working environment (location/application), may cause serious personal injury, death and/or property damage.
  • Risk of fire or electric shock,  installation of the device requires knowledge of the luminaries’ electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
  • Do not alter, relocate or remove the wiring, lamp holder, power supply or any other electrical components.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
  • Do not operate the device if there’s any visible damage to the device.
  • Do not operate the device if there are any signs of smoke, steam, over-heating or crackling noise that can be heard from the device.
  • The manufacturer will not be deemed liable or held responsible for any damage caused by faults or manufacturing defects that may be present in any of its products or the misuse or incorrect installation of the device.
  •  TURN OFF POWER FROM THE MAIN CIRCUIT BEFORE INSTALLING THE FIXTURE. Make sure the fixture is grounded per National Electrical Codes (NEC).

INSTALLATION

  1. Tools needed: Philip’s and Flathead screwdrivers, adjustable wrench, wire nuts, electrical tape, and silicone caulk.
  2. Exercise caution and care when handling fixtures to avoid cuts and abrasions, it is recommended to use rubber sole shoes to avoid the chance of electric shocks.
  3. Carefully unpack and check the contents of the box to be sure everything is included.
  4. Turn OFF the power at the circuit breaker box.
  5. Install Cross Bar (10) to the junction box using two 3/4″ screws (11).
  6. Electrical Connections: Make sure the supply and ground wires go through the Gasket (15). Attach the green or bare copper wire and the green ground wire of the fixture (6) to the crossbar (10) using the groundnut. (Ground wire must be properly attached or unit may not work). Connect the white supply wire to the white fixture wire (8), then cover them with a wire nut (7) or twist together and cover really well with electrical tape. Repeat this with the black supply and black fixture wires (9).  Push the connected wires back into the electrical box.
  7. Install Bracket Screw (1) into the center hole of Fixture Back Mount base (5). Align Fixture over J-box with the Gasket (15) between it and the Canopy. Secure the unit to the Cross Bar by tightening Center Bracket Screw. Loosen the adjustment knobs (13) and aim the lamp heads (14).
  8. Turn on electricity at fuse or circuit breaker box and Test  Unit success of the installation. (see the motion)
  9. Place a small streak of silicone caulk on the edge of the fixture bracket, except at the lower edge. Place the bracket of the fixture so the bracket connecting screw protrudes out of the hole in the fixture bracket. Make sure the fixture is set right side up on the mounting surface. Check that the caulking sealant is completely around the edge of the bracket where it meets the wall’s surface (there should not be caulking at the lower edge). Use the securing nut with a rubber washer (3) to tighten up the bracket to the wall. Adjust the two nuts in the bracket connecting screw if the fixture bracket is not tight against the wall. Make sure the unit is tight and secure.
    LeonLite LED Motion Security Light- 01

MOUNTING BRACKET

LeonLite LED Motion Security Light- 02

WIRING THE LIGHT FIXTURE

LeonLite LED Motion Security Light- 03

MOUNTING THE LIGHT FIXTURE

LeonLite LED Motion Security Light- 04

CAULKING AROUND THE LIGHT FIXTURE

LeonLite LED Motion Security Light- 05

 

OPERATION GUIDE

3 Knobs:
By turning the 3 knobs on the right side, 3 kinds of settings can be adjusted as follows:
Lux Knob: The sensitivity of the Photosensor is changeableLeonLite LED Motion Security Light- 88, turn the first knob clockwise, the light intensity will rise and vice versa.
Time Knob: Lasting time of the lighting is changeable (5secs – 5mins), turning the second knob clockwise raises the delay time and vice versa.

Range: The max distance of the motion sensor is changeable (6.56 – 22.97yds.), turn the third knob clockwise and the detection distance will increase and vice versa.

3 Modes: 3 lighting modes are available by slipping the arrow of the 3-way switch on the left side.
ON-TIME Mode – The light would be on after you switch it on like normal light bulbs.
AUTO Mode – Turn the Lux knob counterclockwise until max. This light will stay off during the day and will turn on at night when motion is detected. After acertain amount of time set by you, the light will turn off when no motion is detected.
Please note that by turning the Lux Knob clockwise, the sensor will detect motion. earlier in the day. At the max setting, it will turn on when motion is detected, even during the day.

Dusk-to-Dawn Mode – Turn the three knobs counterclockwise until the lowest setting and then slip the switch to D2D mode, this puts the light into dusk-to-dawn mode. At night, the light will turn itself on during this mode and then off during the day.
Please note that turning the Lux knob clockwise will lower the photocell sensitivity and if it goes past max, the light will stay on no matter what time of day it is.

LeonLite LED Motion Security Light- 06

WARRANTY

LeonLite warrants that this product is free from defects in materials and workmanship for a period of 5 years from the day of purchase. This warranty does not apply if the product has been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.

Documents / Resources

PDF thumbnailLED Motion Security Light
User Manual · LED Motion Security Light

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. I have the 3 light 300 warm leonlite lights around my home. With one of the lights there seems to be a bulb malfunction. It is coming on but instead of going completely off as the other 2, there is a very small amount of white light still emitting from the one bulb and will not go out when the others are at rest (off).

    Curtis Cuevas asks I have the 3 light 300 warm leonlite lights around my home. With one of the lights there seems to be a bulb malfunction. It is coming on but instead of going completely off as the other 2, there is a very small amount of white light still emitting from the one bulb and will not go out when the others are at rest (off).
    Manuals+ clarified question
    Question

    Why is one of my LeonLite LED motion security lights emitting a faint glow instead of turning off completely?

    Answer

    The issue you are describing, where an LED remains faintly lit even when the switch is 'off', is often referred to as 'ghosting.' This is typically caused by a small amount of residual current leaking through the circuit, which is enough to power high-efficiency LEDs but not traditional bulbs.

    Based on the LeonLite manual and common LED troubleshooting, please check the following:

    • Wiring Integrity: Ensure the fixture is properly grounded. The manual emphasizes that the green or bare copper ground wire must be securely connected to the ground wire of the fixture. Improper grounding can lead to residual voltage in the circuit.
    • Neutral Wire Leakage: If the white (neutral) and black (hot) wires are swapped, or if there is 'induced voltage' from other wires running parallel in your walls, the LED may glow.
    • Switch Compatibility: If this light is connected to a dimmer switch or an illuminated wall switch (one that glows in the dark), these often leak enough current to cause LED ghosting. This fixture should be used with a standard on/off switch.
    • Internal Driver Issue: Since your other two lights are functioning correctly, and only one head on this specific unit is malfunctioning, there may be a fault in the internal LED driver or a moisture leak inside that specific lamp head.

    If the wiring is confirmed correct by a professional and the issue persists, LeonLite offers a 5-year warranty as noted in the manual. You may need to contact their support for a replacement unit if the internal circuitry is defective.

  2. I have already just sent the first email! I wanted to include my date of purchase info. Curtis Cuevas, Amazon ORDER # 112-6202453-6637041. Bought 4 on 02/23/2019. Bronze, 3-head, motion. 5 year warranty. I can return the defective one if you need! In the first email from me you can get all the description of the issue I am having. One of the 3 bulbs is not going all the way out along with the others. A small white light remains when sensor time goes off. This may help collate the two emails together. Thanks!

    Curtis Cuevas asks I have already just sent the first email! I wanted to include my date of purchase info. Curtis Cuevas, Amazon ORDER # 112-6202453-6637041. Bought 4 on 02/23/2019. Bronze, 3-head, motion. 5 year warranty. I can return the defective one if you need! In the first email from me you can get all the description of the issue I am having. One of the 3 bulbs is not going all the way out along with the others. A small white light remains when sensor time goes off. This may help collate the two emails together. Thanks!
    Manuals+ clarified question
    Question

    One of the three LED heads remains partially lit with a small white light after the sensor timer expires. How can I resolve this, and do I need to return the defective unit under the 5-year warranty?

    Answer

    Based on the LeonLite LED Motion Security Light manual, here is the information regarding your issue and warranty:

    • Technical Issue: If one LED head remains partially lit (ghosting) while others turn off, this typically indicates a failure in the internal driver or a leakage current issue within that specific head. Since these are integrated LED units, the individual bulbs are not user-serviceable.
    • Warranty Coverage: The manual confirms a 5-year warranty from the date of purchase against defects in materials and workmanship. As your purchase was in February 2019, your unit should still be covered if within the 5-year window from that date.
    • Return Process: While Manuals+ hosts the product documentation, we do not process warranty claims directly. You should continue your correspondence with LeonLite or the authorized Amazon seller. Typically, manufacturers will require proof of purchase (which you have provided via your order number) and may ask for a photo or video of the defect. They will advise if the physical unit needs to be returned or if a replacement will be sent directly.
    • Troubleshooting: Ensure the fixture is properly grounded as per the 'Installation' section of the manual, as poor grounding can sometimes cause LED glow issues, though a single-head failure usually points to a hardware defect.

    We recommend following up on your email to LeonLite customer support with the specific Amazon order details you provided here.

  3. I’ve purchased 2 LeonLite 20 w dual he’d motion activated floodlights.
    Neither shut off at night when no motiondetected. It is set to Auto. Lux turned all the way counterclockwise.

    Mona asks I’ve purchased 2 LeonLite 20 w dual he’d motion activated floodlights.
    Neither shut off at night when no motiondetected. It is set to Auto. Lux turned all the way counterclockwise.
    Manuals+ clarified question
    Question

    Why do my LeonLite LED motion security lights stay on at night even when no motion is detected?

    Answer

    If your LeonLite LED Motion Security Light is staying on at night without motion, please check the following settings based on the manual's operation guide:

    • Check the Lux Knob: You mentioned the Lux knob is turned all the way counter-clockwise. According to the manual, turning the Lux knob fully counter-clockwise puts the light into D2D (Dusk-to-Dawn) mode. In this mode, the light will stay on all night and turn off during the day, ignoring the motion sensor.
    • Adjust for Motion Sensing: To enable motion-activated shut-off at night, you should turn the Lux knob slightly clockwise away from the minimum setting. This allows the sensor to detect motion rather than staying on continuously in D2D mode.
    • Check the Time Knob: Ensure the 'Time' knob (the second knob) is not set to its maximum, as this can keep the light on for up to 5 minutes after motion has ceased, which may appear as though it is not shutting off.
    • Sensor Interference: Ensure the sensor is not pointed at a heat source (like an AC vent or dryer vent) or moving objects like trees or bushes, which can trigger the sensor and keep the light active.
  4. I have a 20W Dual Head Motion Activated Floodlight. It is under two years old and the motion sensor is malfunctioning. Sometimes the lite comes on if you stand under it and wave, and most of the time it will not lite at all. I live in Arizona and wander if the sun has damaged or blurred the lens till it won’t respond?Can I get a new sensor for the lite under warrantee?

    Joseph Reilley asks I have a 20W Dual Head Motion Activated Floodlight. It is under two years old and the motion sensor is malfunctioning. Sometimes the lite comes on if you stand under it and wave, and most of the time it will not lite at all. I live in Arizona and wander if the sun has damaged or blurred the lens till it won't respond?Can I get a new sensor for the lite under warrantee?
    Manuals+ clarified question
    Question

    How can I troubleshoot a malfunctioning motion sensor on my LeonLite 20W Dual Head Floodlight, and is it covered under warranty?

    Answer

    Based on the LeonLite LED Motion Security Light manual, here are the steps to address your sensor issues and warranty inquiry:

    • Troubleshoot the Settings: Ensure the Lux Knob is not set too low, as this determines the light sensitivity. If it is turned too far counterclockwise, the sensor may only trigger in complete darkness. Also, check the Range Knob; turning it clockwise increases the detection distance (up to 68.9 feet).
    • Environmental Factors: While the manual does not specifically mention sun-blurring, it does note that the sensor detects motion based on heat signatures. Extreme ambient heat (common in Arizona) can reduce the contrast between a person's body heat and the surrounding environment, making the sensor less responsive.
    • Cleaning: Gently wipe the sensor lens with a soft, damp cloth to remove any dust or debris that may be obstructing the infrared signal.
    • Warranty Information: The manual states that LeonLite warrants the product to be free from defects in materials and workmanship for a period of 5 years from the day of purchase. Since your unit is under two years old, it should be covered under this warranty, provided the failure is not due to neglect or mishandling.

    LeonLite typically does not provide individual replacement sensors; instead, they usually replace the entire unit. You should contact LeonLite customer support with your proof of purchase to initiate a warranty claim.

  5. I just had the leonlite installed 9n my back deck. Light comes on with the light switch. 20 seconds later the light starts flashing. Help

    Patty BUTLER asks I just had the leonlite installed 9n my back deck. Light comes on with the light switch. 20 seconds later the light starts flashing. Help
    Manuals+ clarified question
    Question

    Why is my LeonLite LED Motion Security Light flashing 20 seconds after being turned on?

    Answer

    Flashing or flickering in motion security lights often indicates a conflict between the sensor settings and the ambient light levels, or a wiring issue. Based on the LeonLite manual, please check the following:

    • Check the LUX Setting: If the light is flashing, the photocell (Lux sensor) might be detecting its own light or other ambient light, causing it to cycle on and off. Try turning the Lux Knob (the first knob) clockwise to increase the sensitivity to light, or test the unit in D2D (Dusk-to-Dawn) mode by turning the knob counterclockwise to the lowest setting and then flipping the wall switch to see if the behavior stabilizes.
    • Check the Mode: Ensure the light is not stuck in a test cycle. The manual mentions that turning the Lux knob clockwise will detect motion even during the day. If it is in AUTO Mode, it should only trigger when motion is detected at night.
    • Wiring Check: Ensure the electrical connections are secure. The manual specifies that the white supply wire must be connected to the white fixture wire, and the black supply wire to the black fixture wire. Loose wire nuts can cause intermittent power and flashing.
    • Interference: Ensure the light is not reflecting off a nearby shiny surface (like a window or white wall), which can trick the sensor into thinking it is daytime, causing it to shut off immediately after turning on.

    If the flashing persists regardless of knob adjustments, there may be a defect in the sensor or a compatibility issue with the power source (such as being connected to a dimmer switch, which is not supported).

  6. I bought a four pack of LeonLite 12v LED low voltage lighting. Amazon order 112-3193941-9401848. Three of the four lights no longer work.
    It states a five year warranty. When can I expect to receive replacements?

    david hepler asks I bought a four pack of LeonLite 12v LED low voltage lighting. Amazon order 112-3193941-9401848. Three of the four lights no longer work.
    It states a five year warranty. When can I expect to receive replacements?
    Manuals+ clarified question
    Question

    How can I claim the 5-year warranty for my LeonLite 12v LED low voltage lights that have stopped working?

    Answer

    According to the LeonLite manual, the product is covered by a 5-year warranty from the day of purchase against defects in materials and workmanship. This warranty does not cover damage resulting from misuse, abuse, accident, modifications, alterations, neglect, or mishandling.

    To initiate a warranty claim and receive replacements, you should contact LeonLite customer support directly. While the manual confirms the warranty period, it does not list a specific phone number or email. You can typically reach LeonLite through the following channels:

    • Amazon Message Center: Since you provided an Amazon order number, log into your Amazon account, go to 'Your Orders', find the LeonLite order, and select 'Contact Seller' or 'Get product support'.
    • Official Website: Visit the LeonLite official website to find their support contact form or email address.

    When contacting them, be sure to provide your Amazon Order ID (112-3193941-9401848) and a description of the failure to expedite the replacement process.

  7. How do you put in light bulbs in 20w dual sensor motion activated floodlight?

    Liz asks How do you put in light bulbs in 20w dual sensor motion activated floodlight?
    Manuals+ clarified question
    Question

    How do you install light bulbs in the LeonLite 20W dual sensor motion activated floodlight?

    Answer

    Based on the LeonLite LED Motion Security Light User Manual, this fixture features integrated LED technology. This means the light source is built directly into the lamp heads and does not use traditional replaceable light bulbs.

    If the light is not functioning, please check the following:

    • Power: Ensure the circuit breaker is turned on.
    • Settings: Check the 3 knobs on the right side of the sensor to adjust sensitivity (Lux), duration (Time), and detection range.
    • Modes: The unit has three modes (ON-TIME, AUTO, and D2D) controlled by the switch on the left side of the sensor.

    If the integrated LEDs have failed, the entire fixture typically needs to be replaced, as the manual does not provide instructions for bulb replacement. LeonLite offers a 5-year warranty for defects in materials and workmanship; you may wish to contact their support if the unit is within the warranty period.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.