
Solid Apollo 120VAC-DMX-RGB Controller User

Manual Content
- Product Information
- Product Wiring & Installation
- Product Operation Guide
- Product Troubleshooting and Safety
Product Description
Solid Apollo’s 120V AC DMX to RGB Controller is an advanced device that converts DMX signal to RGB. It is the perfect choice for controlling 120V LED fixtures such as Solid Apollo’s RGB Flex Neon LED Strip Lights and Driverless RGB LED Strip Lights.
Compared to other DMX to RGB controllers in the market, this Controller operates at high voltage (100V – 240V AC) and does not need any transformer for powering. It can safely and directly be connected to the standard 120V AC line and it can drive up to 600W at 120V DC.
Product Features
- Converts DMX signal to RGB
- DMX address settable from 1 – 512
- Connects directly to any 120V AC line
- Operates at 100V – 240V AC
- Maximum power of 500W – 1200W
- User-friendly numeric display
- DMX in and out terminals
Product Specs

Product Installation Guide
Installation
In order to successfully and effectively be able to use Solid Apollo’s 120V AC DMX to RGB Controller, it will have to be properly installed with the correct power, data, and LED fixture connections made.
Pre-installation
A. This is a high voltage product, installation should only be done by qualified electricians and according to your local electric code requirements.
B. Make sure to turn off the circuit breaker and ensure that power to the wires that will be used in the installation process is completely shut off before installation starts.
1. Verify that the Power Supply has the right voltage and Wattage required for your application.
2. To connect power to the decoder:
A. Direct hard wiring: The controller can be hard wired directly to any standard 120V line. All you have to do is, securely connect the live wire to the L screw-terminal of the controller’s “AC INPUT” side, and the neutral wire to the N screw-terminal.
B. Using AC power cord: If using an AC power cord such as Solid Apollo’s 5 Foot AC Power Cord, strip-off about ¼” of the cover jacket of the wires in the open end of the power cord. Then securely connect the live wire to the L screw-terminal of the controller’s “AC INPUT” side, and the neutral wire to the N screw-terminal.
Note: You only need to connect the Live and Neutral wires.

3. Connect the RGB fixture’s wires to the “DC OUTPUT” screw terminals of the controller with Red connected to R-, Green to G-, Blue to B-, and the positive (could be black or another color) to V+.

4. If using a DMX Control System, connect its data cables to the “DMX512 Signal” screw-terminals of the controller with the positive data cable securely connected to D1+, the negative data cable connected to D1-, and the ground cable to the GND screw-terminal.

5. If cascading/daisy-chaining multiple units, connect one end of a positive data cable securely to D2+ of the first unit (the unit connected to the DMX Control System) and the other end connected to the D1+ of the next unit. Do the same for the negative data cable with one end connected to the D2- of the first unit and the other connected to the D1- of the next unit (please refer to wiring the diagram – pg.3 for daisy chaining).
6. Once the connections mentioned above are correctly done, you can now power up.
Wiring Diagram

Product Operation



PWM Frequency
Press and hold buttons 1 and 2 for over 3 seconds and the display will show PF1
(PWM Frequency 1). Click button 3 to change frequency selection from 0-9 and A-J.
0=500Hz, 1=1KHz 2=2KHz, …, 9=9KHz, A=10KHz, B=12KHz, C=14KHz,
D=16KHz, E=18KHz, F=20KHz, H=25KHz, J=35KHz.
Press and hold button 3 to confirm the setting.
NOTE: DO NOT set the frequency higher than 3KHz to avoid overheating the device.

Dimming Curve Gamma Value
This parameter is used to adjust the rate at which the output brightness changes at different DMX values.
Humans perceive the brightness change non-linearly and have better sensitivity at low luminance than high luminance.
The non-linear gamma dimming can help make dimming less sensitive for greater precision at various brightness levels (low or high).

Gamma values less than 1 give more precise dimming at higher brightness levels while gamma values greater than 1 give better precision dimming at low brightness.
The default gamma value is 1.5 but the values can be adjusted from 0.1 to 9.9 by holding down all buttons, 1, 2, and 3 simultaneously for over 3 seconds. The display will flash g1.5, the default gamma value. Click buttons 2 and 3 to change the corresponding digits, then hold down buttons 2 and 3 for over 3 seconds to confirm the setting.

Product Troubleshooting
The following recommendations can help in troubleshooting the 120V AC DMX to RGB Controller.
- Controller does not turn ON after powering up :
a. Ensure that the correct voltage requirement of the controller is supplied.
b. Ensure that the wiring of the power input to the device is correctly done with the live wire connected to one of the V+ terminals of the controller and the neutral wire connected to one of the V- terminal (refer to pg.2 – Product Installation Guide). - Controller is ON but LED fixtures are not :
a. Ensure that the LED fixtures are correctly wired in the “OUTPUT” screw-terminals of the controller. - Controller and LED fixtures are ON but LEDs do not respond to DMX control:
a. Ensure that the proper DMX starting address is set on the controller (pg.4).
b. Ensure that the proper DMX signal connections are installed between the controller and DMX control system.
Safety Recommendations
In order to efficiently operate the LEDWizard Dimmer, it is important to correctly and safely install it.
- Obtain the right accessories (LED fixtures, wires, connectors, etc.) beforehand.
- Install the product according to your local electric code requirements.
- Ensure that the product is properly installed with the right accessories and guidelines.
- Ensure that wires or cables are correctly connected to the right ports or terminals.
- Do not try to install the LED fixtures wires while the product is powered on.
- Ensure that the product is placed or mounted in a dry location.
- Ensure that peeled (bare) sections of the wires going into push-down terminals are not extending out of the terminal without the insulation.
- Connect and test the product with the accessories to ensure everything works before final installation.
- Install the product at an accessible area for easy settings adjustment when needed.
The product is backed by a 3-year warranty. Please refer to www.solidapollo.com for more information on warranty coverage.
Read More About This Manual & Download PDF:
Documents / Resources
![]() | 120VAC-DMX-RGB Controller |
References
- Solid Apollo LEDwww.solidapollo.com
- User Manualmanual.tools
