Eccel Pepper C2 RFID Reader

Introduction
Device Overview
Features
- Low cost RFID Reader with MIFARE® Classic® in 1K, 4K memory, ICODE, MIFARE Ultralight®, NTAG21x
- lifetime firmware updates
- Command interface via UART
- UART baud rate up to 921600 bps
- Hight speed USB-UART emulated interface
- HID keyboard emulation
- Configurable RGB LED indicator for RFID events
- 6 configurable GPIOs
- Stand-alone mode (polling)
- High transponder read and write speed
- -25°C to 85°C operating range
- Multiple internal reference voltages
- RoHS compliant
- CE (RED) and UKCA compliant.
FCC/ISED/PSE and other approvals easily obtained
Description
The Pepper C2R RFID reader is a complementary addition to the Pepper family, designed for applications that require increased RF output and greater read-range potential while retaining compatibility with most of the tag types and protocols supported by the Pepper C1. It includes lifetime firmware update support, providing access to future improvements and security updates. Its configurable USB interface can operate as a virtual serial port or as a HID device, including keyboard emulation. With its integrated antenna and cost-optimised design, Pepper C2R provides powerful RFID functionality in a ready-to-use format at a competitive price. 
Applications
- Access control
- Monitoring goods
- Approval and monitoring consumables
- Pre-payment systems
- Managing resources
- Contact-less data storage systems
- Evaluation and development of RFID systems
Electrical specification
Absolute maximum ratings
Stresses beyond the absolute maximum ratings listed in the table below may cause permanent damage to the device. These are stress ratings only, and do not refer to the functional operation of the device that should follow the recommended operating conditions.
| Symbol | Parameter | Min | Max | Unit |
| TS | Storage temperature | -40 | +125 | °C |
| TA | Ambient temperature | -40 | +85 | °C |
| VDDMAX | Supply voltage (USB or J4 header) | 3 | 5.5 | V |
Table 2-1. Absolute maximum ratings
Operating conditions
| Symbol | Parameter | Min | Typ. | Max | Unit |
| TS | Operating temperature | -25 | 25 | +85 | °C |
| H | Humidity | 5 | 60 | 95 | % |
| VDD | Supply voltage (USB or J4 header) | 3 | 5 | 5.5 | V |
Table 2-2. Operating conditions
DC characteristics (VDD = 5 V, TS = 25 °C)
| Symbol | Parameter | Min | Typ. | Max | Unit |
| VOUT | Output voltage (regulator output, 3V3 pin on the J1 header) | 3.23 | 3.3 | 3.37 | V |
| VIH | High-level input voltage (J1 header) | 0.75 x VOUT | – | VOUT + 0.3 | V |
| VIL | Low-level input voltage (J1 header) | 0 | – | 0.3 x VOUT | V |
| VOH | High-level output voltage (J1 header) | 0.8 x VOUT | – | – | V |
| VOL | Low-level output voltage (J1 header) | – | – | 0.3 x VOUT | V |
| VORS232 | V output RS232 (J2 header, RS232_TX pin) | – | 5 | – | V |
| VIRS232 | V input RS232 (J2 header, RS232_RX pin) | -25 | – | +25 | V |
Table 2-3. DC characteristics
Current consumption (VDD = 5V)
| Symbol | Parameter | Typ. | Max | Unit |
| IRFON | RF field on (no tag, pooling 200ms) | 97 | 110 | mA |
| RF field on (tag in read range, pooling 200ms) | 295 | 315 | mA | |
| RF field on (continuously) | 300 | 322 | mA | |
| RF field on (tag on antenna) | 316 | 336 | mA | |
| IRFOFF | RF field off | 23 | 30 | mA |
| Sleep mode | RF field off | 4 | 5 | mA |
Table 2-4. Current consumption
Getting started
IO and peripherals 
RS232/485 header – this connection is for optional built in RS232/485 converter. These options are available here: https://eccel.co.uk/product/pepper-c2-fcc-approved-rfid-reader
J1 header description
| 1 | UART2 TX |
| 2 | UART2 RX |
| 3 | GPIO 01 |
| 4 | GPIO 02 |
| 5 | GPIO 03 |
| 6 | GPIO 04 |
| 7 | GND |
| 8 | 3.3V Output |
| 9 | GPIO 05 |
| 10 | GPIO 06 |
2 J2 header description (RS232 version only)
- Not connected
- Not connected
- RS232 RX (from host to the Pepper C2, max input voltage level ±25V)
- RS232 TX (from the Pepper C2 to host, max output voltage level ±5V)
3 J2 header description (RS485 version only)
By default, the Pepper C2 reader operates in full-duplex mode, using all four wires for RS485 communication. For half-duplex communication, connect pins A and Y together, and pins B and Z together.
- A Noninverting Receiver Input
- B Inverting Receiver Input
- Z Inverting Driver Output
- Y Noninverting Driver Output

4 J3 header description
The J3 header is an additional power supply output socket.
- +5V output (100mA)
- GND
5 J4 UART0 header
This is the UART0 header in the TTL standard with 3.3V levels. This is the same UART as it available on the USB port in the USB version.
- Vin – Power supply, 3-5.5Voltage
- UART0 TX – UART TX data from the reader
- UART0 RX – UART RX data to the reader
- GND

Typical connection
The Pepper C2 device can be connected to a host computer using a standard USB-C cable. In the same way it can be powered to operate as a standalone device by using power sources such as a USB charger or power bank. The computer operating system should recognize this device as a USB to UART bridge or a USB to Serial port converter and it should appear in
Windows device manager as a COM port. By default this COM port can be used for communication using the binary protocol described below. The Reader also has the UART2 interface (J1 header) where the user can view console logs which contain additional information about temporary executing commands. The default configuration: baud: 115200, Data: 8 bit, Parity: none, Stop bits: 1 bit, Flow Control: none. 
Hint – If you don’t have a USB-UART converter to see the logs on the UART2 (J1 header), you can temporary change the default log interface from UART2 to UART0 in Cx-Client UART configuration button. Then, the logs should be available on the USB port







pHID keyboard emulation
The RFID reader can be configured to enable USB port emulation of the HID Keyboard profile. With this functionality, UID numbers of tags read during polling are transmitted as a keyboard input stream to any host device that accepts USB keyboards. To activate this profile, the Cx-Client application should be used to select the HID Keyboard profile for the USB port within the USB/UART configuration menu.
Once the device is configured via the USB/UART0 interface in HID Keyboard mode, further connection to this port using the Cx-Client application becomes unavailable. In order to temporarily restore the binary protocol, the button on the reader must be pressed and held for 3 seconds. During this process, the device’s RGB LED blinks once every second and flashes red when the default UART emulation profile has been temporarily restored. Additionally, configuration options allow enabling automatic transmission of the ENTER key after each UID is sent.
Factory reset
To restore the device to its factory default settings, the button on the device must be pressed and held for 10 seconds. The device will indicate the completion of the factory reset process by flashing the RGB LED in white.
Mechanical dimension

Configuration and functional description
- Here is the document describing configuration, communication protocol, commands and all functions of the Pepper C2 reader: https://eccel.co.uk/wp-content/downloads/Pepper_C2/C2-software-manual.pdf
- Eccel provides a variety of free tools & libraries ready to be downloaded from this link: https://eccel.co.uk/support-free-libraries/ us at technical@eccel.co.uk. Our team can provide integration support and, where required, adapt the software and/or hardware to meet specific customer requirements. We specialize in developing custom solutions. Further information is available at: https://eccel.co.uk/custom-design/
RF Emissions and Susceptibility Approvals
Eccel have tested and declare that this product meets all the requirements of the relevant RF directives (RED) to be declared CE (European Union) and UKCA (United Kingdom) compliant. Please see our declaration of conformity for this on the downloads tab of the product webpage. This product is designed to be incorporated into products easily and quickly such that those products can pass any national or regional statutory RF requirements and certifications such as FCC (USA), ISED (Canada) and PSE (Japan) for example.
This product is designed to meet all statutory RF requirements applicable worldwide using the most cost effective but robust design methodology. Eccel is pleased to offer customers very cost-effective certification for their end equipment that incorporate this product. Prices start from £3K per approval/ certification. Please contact us for more details at sales@eccel.co.uk .
7. Revision history
| Revision | Date | Changes |
| 1.1 | 28-July-2025 | Initial release |
| 1.2 | 03-Dec-2025 | Current consumption updated |
| 1.3 | 24-Sep-2026 | Product photo update |
- MIFARE, MIFARE Ultralight, MIFARE Plus, MIFARE Classic, and MIFARE DESFire are trademarks of NXP B.V.
- No responsibility is taken for the method of integration or final use of the C2 readers
- More information about the C2 reader and other products can be found at the Internet site: www.eccel.co.uk or alternatively contact ECCEL Technology by e-mail at: sales@eccel.co.uk
Documents / Resources
![]() | Pepper C2 RFID Reader |
References
- Custom RFID & NFC Product Development | Eccel Technologyeccel.co.uk
- Pepper C2 - 2 W Long-Range RFID/NFC Reader | Ecceleccel.co.uk
- Support - Eccel Technology - RFID made simpleeccel.co.uk
- Custom RFID/NFC solutions for your bussiness - Eccel Technology - RFID made simplewww.eccel.co.uk
- User Manualmanual.tools
