LOOPGEAR SK06 Laser Flashlight Instructions

1. MAIN LIGHT OPERATION
   
2. UV OPERATION
   
3. SIDE LIGHT OPERATION
   
4. LASER LIGHT OPERATION
   
5. CHARGING/DISCHARGING
   

LIGHTING

1. Main light: Hall rotary dial points to the main light
   Click: Turn on/off the main light
   Double click: Turn on the Turbo mode of main light
   Triple click: Triple-click to activate the Strobe mode; under such mode, long press to switch among Strobe-SOS-beacon
   Long press: When the light is on, press and hold to adjust brightness levels. When the light is off, press and hold to enter Moonlight mode.
2. UV light: Hall rotary dial points to UV light
   Click: Turn on/off the UV light
   Long press: When off, long press to turn on UV; single click to turn it off
3. Side light: Hall rotary dial points to the side light
   Click: Turn on/off the side light
   Double click: Switch side light mode (memory mode)
   Triple click: Enable red-blue flashing. Under the mode, long press to switch among red-blue flashing-red-white flashing-red SOS-white beacon
   Click for 4 times: Adjust brightness level
   E-tritium tube: 5-click to 7-click switches the e-tritium tube between red, green, blue, and off, with memory
   Long press:
   When the light is on:
   White light: Long press to adjust brightness level (memory mode)
   Solid color: Long press to adjust color (memory mode)
   Breathing mode: Long press to adjust color (memory mode)
   Color cycle: Long press to adjust speed (memory mode)
   Under disabled status:
   Enable the moonlight mode of side light
4. Laser light: Hall rotary dial points to the laser light
   Click: Turn on/off the laser light
   Double click: Turn on the main light when the laser light is on
   Triple click: Turn on the UV light when the laser light is on
   Long press: Adjust brightness level when the light is on(memory mode) Under disabled status, long press to enable the moonlight mode of laser light
   Tip: When the battery indicator is red, the laser beam appears dim.
5. Charging/Discharging
   Open the charging port cover and connect the device via the USB-C port to charge or discharge. During charging, the red indicator breathes. When fully charged, the ice-blue indicator remains on. During discharging, the ice-blue indicator breathes. When the battery is low, the red indicator flashes. Click once to turn the battery indicator on/off. During charging or discharging, press and hold to turn on the light (Medium mode of the current lighting mode); press and hold again to turn it off.
6. Locking & unlocking
   Electronic lock: Long press when the device is powered off.
   Lock: When the light is off, long press to turn on the light of such mode, and it will enter the locked state within 2 seconds. Unlock: Long press for 1 second to unlock and turn on the light of such mode.
7. Battery Indicator
   The battery indicator is above 30% when the rotary dial is in ice blue color, 10%-30% when in purple; below 10% when in red

PACKAGE CONTENT

• Flashlight Unit * 1
  
• Charging Cable * 1
  
• User Manual * 1
  
• wrist lanyard * 1
  
• Spare O Ring * 1
  
• clip * 1
  

Warning

1. Avoid direct eye exposure to the light, including the main light, laser, and UV light, as it may cause eye or skin injury.
2. Do not block the light opening at close range; the heat emitted from the light may ignite nearby objects.
3. When storing for a long time, it’s best to keep the battery level between 30% and 80%.
4. Do not place the flashlight in a backpack, fabric bag, or fusible plastic container under high-temperature conditions.
5. Do not store the flashlight in a car or similar places where the temperature may exceed 60°C.
6. Keep the charging interface clean and dry.
7. Do not short-circuit the charging port with metal or conductors.
8. Do not disassemble the product.
9. Do not immerse the flashlight in seawater or corrosive liquids, as this will cause damage to the product.
10. When placing in a backpack or pocket, please set the flashlight to Lockout mode to prevent accidental activation.
11. Incompatible with two CR123 or RCR123 batteries. Do not insert.