VEVOR BDMC-1 Button Maker Machine
Specifications
| Product model | BDMC-1 |
|---|---|
| Finished badge specification | 58 |
| Machine body color | Gold and Black |
| Paper requirements | 127g–160g (paper thickness range appears in the accessories/introduction section); also listed as 115–157g in the model/parameter section |
| Paper size | Should be the same as the transparent film |
| Included accessories (with machine) | Metal cover (x100), Plastic back (x100), White paper (x50), Transparent film (x100), Round cutter (x1), A5 cutting mat (x1), Allen key (x2), Magic book (x1), User manual (x1) |
Quick Guide
- Rotate and fix the handle to the machine.
- Put the metal cover into the Down Mold (A).
- Place the white paper into Down Mold (A). If making a patterned badge, replace white paper with patterned paper and align the pattern with the side arrow marks.
- Place the transparent film into Down Mold (A).
- Rotate the Down Mold (A) under the Upper mold, ensuring the upper and lower molds are on the same vertical line.
- Hold the handle and press down until the bottom.
- Place the plastic back into Down Mold (B) and align the pin with the side arrows.
- Rotate Down Mold (B) under the Upper mold, ensuring the upper and lower molds are on the same vertical line.
- Hold the handle and press down until the bottom.
- Take out the badge; the operation is complete
Product info
NOTE: Please be sure to read the manual before operating!
The finished products made before you are familiar with the operation may not be successful. Please practice more to get familiar with the feeling!
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
SAFE INSTRUCTIONS
- This badge machine is only applied for the intended purpose. Don’t apply in other applications which exceed safety considerations.
- Children cannot operate this product unless accompanied by an adult.
- Pay attention to safety during operation, and avoid crushing fingers.
SAVE THIS MANUAL
STRUCTURE DIAGRAM
ACCESSORIES INTRODUCTION
OPERATION
- Rotate and fix the handle to the machine.
- Put Metal Cover in the Down Mold(A).
- Put White Paper in the Down Mold(A).
- Note: If you want to make a badge with a pattern, the white paper needs to be replaced with a patterned paper.
- Align the pattern with the arrow marks on the side edge.
- Put Transparent Film in the Down Mold(A).
- Rotate the Down Mold(A) under the Upper mold.
- NOTE: the upper and lower molds must be on the same vertical line.
- NOTE: the upper and lower molds must be on the same vertical line.
- Hold the handle with one hand and with the other hand hold the Handle, then press down until the bottom.
- NOTE: It is OK that the PINS don’t go through the up plate of the Upper Model.
- NOTE: It is OK that the PINS don’t go through the up plate of the Upper Model.
- Put the Plastic Back in the Down Mold (B).
- Note: Align the pin with the side arrows.
- Note: Align the pin with the side arrows.
- Rotate the Down Mold (B) under the Upper mold.
- NOTE: the upper and lower molds must be on the same vertical line.
- NOTE: the upper and lower molds must be on the same vertical line.
- Hold the handle with one hand and with the other hand hold the Handle, then press down until the bottom.
- NOTE: It is OK that the PINS don’t go through the up plate of the Upper Model.
- NOTE: It is OK that the PINS don’t go through the up plate of the Upper Model.
- Step10：Take out the badge and the operation complete.
TROUBLESHOOTING
FAILURE AND TROUBLESHOOTING
| Failure Appearance | Possible Reasons | Troubleshooting |
|
After following step 6, the Tin up cover is not attached to the upper mold. |
1. Unsuitable operating method. |
1. When working under step 6 PINS go through the up plate of the Upper Model.
2. The up and down mold must be on the same vertical line when closing. |
|
2. Too much lubricating oil in the up mold. |
3. If you find too much lubricant on the
upper mold, wipe it off completely with a clean cloth or paper towel. |
|
|
Badge incomplete after following step 9 |
1. Unsuitable operating method |
1. When following step 8, the upper and lower molds must be on the same
vertical line. |
| 2. Unsuitable paper thickness | 2. Use the stipulated thickness paper. | |
|
3. Up mold screws loosen |
3. Place the up mold on the machine body, use the complimentary Allen key to fix the screws in the up mold
internal hole center. |
|
|
Not tightly press the badge, pressed in but not firm |
1. The downward press is not in
place, not press to the bottom. |
1. Need press to the bottom when
downward pressing. |
| 2. Paper is thinner | 2. Change to use a slightly thicker paper. | |
| 3. ( 58mm ) Configured metal back consumables do not place the
washer |
3. Right side mold place 2mm thickness washer when using the metal back
consumables. |
|
|
Up mold unable to lift up after pressing manufacture, blocked |
1. Up and down mold position deviated 2. The paper is incorrectly cut round or blocked by a foreign object. |
Use a sharp tool (such as a straight screwdriver) to align to middle merge position clearance which is between up and down mold, and pry open with the object like a hammer (Attention: Just tap it, generally, it will not be too
tightened). |
MODEL AND PARAMETER
| Product Model Description | BDMC-1 |
| Manufactured Badge
Specification |
Φ 58 |
| Machine Body Color | Gold ＆ Black |
| Paper Requirements | 115-157g Copper Plate Paper |
|
Accessories With Machine |
1. Metal Cover x100
2. Plastic Back x100 3. White Paper x50 4.Transparent Film x100 5. Round Cutter x1 6. A5 Cutting Mat x1 7. Allen Key x2 |
| 8.Magic Book x1 | |
| 9.User Manual x1 |
Documents / Resources
 | BDMC-1 Button Maker Machine |
References
- User Manualmanual.tools