V3 controller manual
version 7.M409
V3 Throttle Controller

- On/Off Button
- Throttle Gears/Navigation
- Boost/Select Button
- Throttle Trigger
- Wireless Charging Point
- Removable Bump Guard
Scan QR Codes for online articles/ videos OR search keywords on online Help Centre.
UPDATE BEFORE USE/OFTEN VIA FOIL DRIVE APP
TO VIEW FIRMWARE NUMBER, WHILE POWERED OFF, PRESS & HOLD + & –
Contains FCC ID: 2BLIO-MTFDV3 This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: 1. This device may not cause harmful Interference, and 2.
This device must accept any interference received including interference that may cause an undesired Operation
Made in China. Model Number: Foil Drive V3 Controller. UN38.3
Foil Drive Pty Ltd. DC: 3.7V, 3.7Wh ISED ID: 22326-MTFDV3
Battery Registration: DE 87733291 WEEE Registration: DE 19270757
![]()

CHANGE SCREEN DISPLAY
Press B button
- Connection to Device
- GPS Activated
- Controller SoC
- Battery SoC*
- Gear**
- Throttle Percentage***
- Live Session Time
- Live Speed
- Total Session Distance
- Top Session Speed
- System Watts
- Battery Temperature
- Motor RPM
- Current Draw Amps
- Battery Voltage
*State of Charge
**May also read T Indicating you are in Trigger Mode, not Gear Mode.
***May also read Lock.
To unlock hold B for 2 seconds.
ON/OFF Hold + for 3 seconds
MANUAL TRIGGER UNLOCK/RELOCK Hold (B for 2 seconds
ACCESS THE SETTINGS MENU Press + and together
SCROLL Press + or -to scroll up/down
SELECTING AN OPTION Press (B) button
SAVE AND EXIT Hold button
THROTTLE MODES
You have the choice of controlling your motor via gears or a throttle trigger. Change modes in settings menu 3. Throttle
https://help.foildrive.com/en-US/2709851-a64c1818f95e45e78b7f1ed34f97a557
Mode based on your preferences.
Scan QR for Throttle Modes
TRIGGER MODE
Trigger mode allows you to use the full range of throttle (0-100%) via a proportional throttle trigger, the more you pull the trigger, the more power you get. Trigger Mode is preset to 100% throttle limit, this limit can be decreased in the setting menu 4. Throttle Mapping.
GEAR MODE
Gear Mode is a helpful for learners or for efoiling. The throttle is split into gears 1 to 5, each gear offering a different power output. To increase or decrease the gears press + or –
Gear 1-2 Gentle throttle for getting to your feet and traversing
Gear 3-4 Balanced power and control for when you are on foil Gear 5 Full thrust for take-offs and maximum speed
Each gear has a pre-set maximum throttle limit. Gear 1 low power/throttle, gear 5 high power, the trigger controls how much of that power you use. Pre-set throttle % limits/gear ratios can be adjusted in menu option 4. Throttle
Mapping
For Example: G1 = Set to 55%
If you pull trigger halfway in G1, you will reach 30% throttle. If you fully pull the trigger, you will reach that gears limit 55%. Press + to increase gears.
Safety Note: The Motor only works while the trigger is pressed. When you release the trigger, the motor will stop.
BOOST MODE
Boost is most useful in when you need quick acceleration, generally right before flight, avaibale both in Gear and Trigger Mode. When active, boost will engage up to the value you have pre-set in the app and is ONLY available for a limited time.
Activate in Gear Mode: Pull the Trigger to maximum throttle, then press and hold B. Full Boost will activate despite what gear you are in.
Activate in Trigger Mode: Pull the Trigger to the 95-100% throttle range.
https://help.foildrive.com/en-US/boost-mode-%7C-foil-drive-app-293439
Tip: Wait to use your Boost until right before take-off, using it too early may result in false start. Use 90% throttle until you’re ready to fly, then pull full throttle or hit B to engage.
CRUISE CONTROL
Recommended for advanced riders only. Cruise control is great for traversing or when using a paddle as the motor will stay running without having to pull the trigger. OFF from factory, to turn it on/adjust cruise speed, see menu 10. Cruise Control. We recommend 35% Cruise Throttle.
https://help.foildrive.com/en-US/setting-up-cruise-control-216645
ACTIVATE CRUISE CONTROL
Hold – for 2 seconds, then pull trigger above 20%
CARE & MAINTENANCE
https://help.foildrive.com/en-US/cleaning-your-kit-203714
Soak in fresh water after every use to avoid build up of salt or debris. Pull trigger and shake controller to free water from inside.
Spring Broken? The controller has a double coiled spring. If one coil breaks, the second coil will return you to shore. Replace spring before continued use.
Check regularly and change proactively relative to your volume of use.
LOCK FUNCTIONS
When Locked, the motor will NOT engage via the throttle. The screen will read LOCK in the throttle window on the main screen.
Note: The controller must be OFF, not Locked, when touching the motor/propellers, carrying your board, or entering/exiting the water.
https://help.foildrive.com/en-US/throttle-lock-v2-controller-feature-411702
There are multiple reasons the LOCK message may show on your screen:
Throttle Lock On Start is activated. The controller will be Locked every time you power on. Press and hold B to unlock, or disable in setting menu 8. Lock on Start. ON from factory, we recommend leaving this on.
Throttle Auto Lock is activated when the motor has not been engaged for a pre-set amount of time. Press and hold B to unlock, or disable in setting menu 9. Throttle Auto Lock. OFF from factory, we recommend a 10 second auto lock for beginners.
Manual Lock is activated. Manual Lock allows you to re-lock the controller at any time, useful when getting back on your board after a fall. Press and hold B to unlock, or re-lock.
Tilt Sensor is active and screen will read TILT (Old Software may read LOCK). Ensure your board is upright to automatically disable Tilt Lock. See the System User Manual for information on the Tilt Sensor.
This can be disabled in menu 7. Tilt Sensor.
Note: When Lock is active, the Inactivity and Activity Alarms will still function unless turned off via the App. Scan the QR code to learn more.
CHARGING THE CONTROLLER
- Align symbols on controller with charging symbol on the pad See Below
- Ensure the controller is laying flat on the pad
- When aligned, pad will illuminate blue and controller screen will power on
- The controller will display ‘Charge Complete’ when full
Note: Do not leave the controller on charge once charging is complete.
If left on charge, it may damage internal components.
Note: Controller battery runtime will reduce when screen brightness is turned up.
To extend battery runtime, reduce brightness in setting menu 13. Brightness.
IMPORTANT: You MUST use a high quality wall adaptor with the charging pad. Adaptor output MUST be rated greater than 5V-1.5A.
HAVE A FAULT? STEP ONE, FACTORY RESET
The first step in troubleshooting should always be a Factory Reset and soak in warm water. There are two ways to do so:
Manual Button Overide: While on any screen, press and hold = – and B button together until screen displays “Factory Reset”.
Menu Option 15: Navigate to menu option 15, press B, follow instructions.
SETTINGS MENU
- PAIR
If the Pair Icon is flashing, the system and controller are not connected. Be mindful of other nearby Foil Drive systems to ensure correct system pairing occurs.
1. Connect your battery Note: If flashing persists, follow the steps below
2. With the battery unplugged, enter Pair Menu
3. Follow instructions on controller screen
4. Controller will display “Pairing Complete” when successful
5. Ensure Lock is disabled (Hold B) and motor is clear of obstacles
6. Pull the trigger to test motor operation
Note: If testing the motor with tilt-sensor active, the board needs to be the upright and horizontal for your motor to engage. - CALIBRATE
If controller does not reach 100% throttle OR does not return to 0%, re-calibrate.
Enter the Calibrate Menu and follow instructions on screen. If issues persist, inspect internal springs. - THROTTLE MODE
Select Throttle Modes Toggle Gear/Trigger mode with + and – - THROTTLE MAPPING GEAR AND TRIGGER MODE
If in Trigger Mode skip Step 1.
1. Press + or to navigate up and down Gears 1 to 5 (Gear Mode Only)
2. Press B to begin mapping the throttle limits
3. Press + or to cycle through values
4. Press B to confirm value - BATTERY VOLTAGE
The voltage on your controller MUST match the voltage on the battery for correct data, check this menu when changing battery types. Toggle Battery Voltage options with + and –
Fusion 43V |
MAX 40V |
Slim 40V |
Slim Endurance 28V
Assist PLUS 28V |
Assist 22V - GPS (ON/OFF) ON FROM FACTORY
Deactivating will disable live speed/distance information. - TILT SENSOR (ON/OFF) ON FROM FACTORY
Fusion Only. Tilt Sensitivity can be programmed in the app. - LOCK ON START (ON/OFF) ON FROM FACTORY
Turn on/off Lock on start – Locks when controller powers on. - THROTTLE AUTO LOCK OFF FROM FACTORY
Throttle locks after a pre-set period of the trigger not being pulled.
1. Press B to edit pre-set Auto Lock time
2. Press + or to cycle through values
3. Press B to confirm value - CRUISE CONTROL OFF FROM FACTORY
1. Press B to edit pre-set Auto Lock time
2. Press + or to cycle through values
3. Press B to confirm value - UNITS
Change between Metric and Imperial (Kilometers/Miles, Celcius/Fahrenheit). - SCREEN SLEEP ON FROM FACTORY
Screen brightness dims when the controller buttons have not been used for more than 10 seconds. Screen will reactivate when any button/trigger is pressed. Screen Sleep is enabled to extend battery runtime of the controller. - BRIGHTNESS
Adjust Screen Brightness. A dimmer screen will extend battery runtime. - AUTO POWER OFF OFF FROM FACTORY
Automatically turn controller off when the buttons have not been used for more than the pre-set time. To adjust:
1. Press B to edit the pre-set time
2. Press + or to cycle through values
3. Press B to confirm value
![]()
Documents / Resources
![]() | V3 Throttle Controller |
References
- User Manualmanual.tools
