KEMIMOTO UTV Soft Window Panel

Specifications
- Product Type: UTV Soft Rear Window / Soft Window Panel
- Material: Heavy-duty Oxford fabric with transparent PVC window
- Weather Resistance: Water-resistant, windproof, dustproof
- Window Style: Roll-up or zippered ventilation window
- Installation: Tool-free strap or hook-and-loop mounting
- Compatibility: Various Polaris, Kawasaki, Honda, and Can-Am UTV models
- Features:
- Reduces dust, mud, snow, and cold air entry
- Clear rear visibility through the PVC panel
- Tear-resistant fabric construction
- Lightweight and foldable design
- Some models include reflective strips and storage pockets
- Use: Off-road riding, trail protection, winter riding comfort
- Maintenance: Wipe clean with mild soap and water; avoid harsh chemicals and prolonged folding of PVC window sections
Usage Instructions
Installation Process
- Positioning and Pre-Installation
- Lay the soft window/door panel flat on the ground
- Compare the roll cage and door frame of the vehicle, roughly compare their positions, and mark the fixing points of the Velcro and straps.
- Fixed Velcro/Self-adhesive Strip
- Clean the corresponding positions of the roll cage and door frame with alcohol and let them dry.
- Peel off the Velcro backing, stick it tightly at the marked position, and press for 30 seconds to ensure firmness.
- If the kit includes self-adhesive fixing strips, they should also be cleaned and attached to the roll cage.
- Install the Main Body of the Soft Window/Door Panel
- One person holds the soft window steady, while the other aligns its edge with the Velcro and presses down from the top to secure it.
- Use the accompanying straps or plastic buckles to secure the fixing points on the soft window to the roll cage one by one, ensuring a tight fit.
- Adjust the position of the transparent window to ensure clear visibility and no wrinkles.
- Fix the Bottom and Sides
- Align the bottom edge of the soft window with the door frame or lower half door panel, and secure it with a snap fastener or Velcro.
- Check all fixing points to ensure they are not loose, the edges are not raised, and prevent air and dust leakage during driving.
- Functional Testing
- Test whether the transparent window can be smoothly rolled up and fixed.
- Close the car door and check the fit between the soft window and the car door to ensure no interference.
- Gently pull the soft window and confirm that all fixing points are secure.
NOTICE BEFORE INSTALLATION
- For optimal performance, the Soft window Panel is designed to be used in conjunction with the vehicle roof and front/rear windshields to create a relatively sealed and warm environment. It is not advisable to use this product in an open setting, as strong winds could potentially cause damage to the straps, hook-and-loop tapes, and body decals.
- For an easy action, loosen the fixation clamps of your vehicle’s roof, front/rear windshields, before starting installation.
- Use denatured alcohol and clean any area where the product will be installed.
- Should you notice whiteness, cloudiness, wrinkles, or ripples on the Soft Panel, be aware that these imperfections usually resolve after
exposure to sunlight and/or heat. To expedite this process, gently warm the affected areas using a heat gun or hair dryer. Caution: Do not overheat, and avoid concentrating heat on one area for too long to prevent damage to the Soft Panel.
By following these precautions before installation to ensure a successful setup and maintain the integrity of the UTV Soft Panel.
ABOUT CLEAN AND CARE
- When cleaning the Soft Panel, use only soap and water. Do not use detergents, window cleaners, or solvents as they may damage the material.
- Do not clean the transparency window with a dry cloth or rag to avoid scratching.
- Routinely clean and lubricate the zipper:
- Clean the zipper with a toothbrush using soap and water. After drying, lubricate the teeth with zipper lubricant, or alternatively, you can use soap or candle wax.
- If the zipper sticks, do not force it. Remove any debris from the teeth and reapply lubricant. Ensure that the zipper moves smoothly before
trying to open or close it further.
- The self-adhesive tape is very sticky and could damage the body decals if removed hastily. If you need to remove the self-adhesive tape, we recommend doing so slowly and carefully. Press down on the body decal or panel with one hand while gently peeling away the tape with the other hand.
- Do not fold the Soft Panel for storage. If your model has zippered windows, ensure they are closed before rolling up the panel for storage.
- Do not tow the vehicle at highway speeds with this product installed. Please follow these cleaning and care instructions to ensure the longevity and performance of the UTV Soft Panel.
Troubleshooting
- Problem: Loose fit or air/dust leakage.
- Solution: Recheck all fixing points (Velcro, straps, snap fasteners). Ensure they are securely fastened and that edges are not raised. Adjust as necessary.
- Problem: Wrinkles in the transparent window.
- Solution: During installation, carefully adjust the position of the transparent window to ensure clear visibility and no wrinkles before fully securing.
- Problem: The transparent window is not rolling up smoothly.
- Solution: Ensure there are no obstructions. If zippered, ensure zippers are clean and lubricated if necessary.
- Problem: Interference with the car door.
- Solution: After installation, close the car door and check the fit. If there’s interference, slightly adjust the soft window’s position or tension.
Documents / Resources
![]() | UTV Soft Window Panel |
References
- User Manualmanual.tools
Published: May 14, 2026

