SYSGRATION BSI150511 TPMS Sensor

Safety Instruction
Read all instructions, and safety instructions and review all illustrations before installing the sensor. For reasons of safety and for optimal function, manufacturer recommends that any maintenance and repair work is carried out by trained experts only and according to the guidelines of the vehicle manufacturer. The valves are safety-relevant parts which are intended for professional installation only. Failure to follow installation instructions may result in the failure of the vehicle TPMS sensor to operate properly. The manufacturer does not assume any liability in case of incorrect, faulty or incomplete installation of the product.
Caution
- The manufacturer’s assemblies are replacement or maintenance parts for vehicles that have a factory-installed TPMS.
- Make sure to program the sensor by manufacturer’s programming tool for your specific vehicle make, model and year before installation.
- In order to guarantee optimal function, the sensor may only be installed with valves and accessories by the manufacturer.
- Upon completion of installation, test the vehicle’s TPMS system using procedures described in the original manufacturer’s user guide to confirm proper installation.
Limited Warranty
Manufacture warrants to the original purchaser that the TPMS sensor complies with manufacture product specifications and shall be free from defects in material and orkmanship under normal and intended use for a period of twelve (12) months rom the date of purchase.
The warranty shall be void if any of the following occur:
- Improper or incomplete installation of products
- Improper usage
- Induction of defect by other products
- Mishandling of product and/or any modifications to the products
- Incorrect application
- Damage due to collision or tire failure
- Racing or competition
The manufacturer’s sole and exclusive obligation under this warranty will be to repair or replace at the manufacturer’s discretion, without charge, any merchandise that does not conform to the above warranty and is returned with a copy of the original sales or satisfactory evidence of date of purchase, to the dealer from whom the product was originally purchased orto manufacturer. Notwithstanding the foregoing, in the event that the product is no longer available, manufacture’s liability to the original purchaser shall not exceed the actual amount paid for the product.
Manufacture expressly disclaims all other warranties, express or implied, including any warranty of merchantability. For fitness for a particular purpose. Under no circumstances shall the manufacturer be liable to any party or person for any other amounts, including but not limited to labor charges for installation or reinstallation of products nor shall the manufacturer be liable for any other damages, including but not to state. It is exclusive and in lieu of all other obligations, liabilities or warranties, whether express or implied.
Installation Guide
WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS OR THE USE OF IMPROPER TPMS SENSORS MAY RESULT IN THE MOTOR VEHICLE TPMS SYSTEM FAILURE, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
Each time a tire is serviced or dismounted or if a sensor is removed, it is MANDATORY to replace the nut, and valve to ensure proper sealing. The TPMS sensor nut must be properly installed and tightened for proper installation.
Carefully follow instructions and use a torque wrench to ensure proper installation. Failure to torque the TPMS sensor nut properly will void the warranty and the TPMS may not function properly.
Remove the valve cap and core and deflate the tire. Use the bead loosen to unseat the tire bead.
With a screwdriver, remove the fastening screw and sensor from the valve stem. Then loosen the nut and remove the valve.
Slide the valve stem through the valve hole of the rim. Tighten the nut with 4.0 Nm by torque wrench. Assemble the sensor and the valve against the rim and tighten the screw.
Clamp the rim onto the tire chager so that the valve faces the assembly head at an angle of 1800.
Exploded view

Warning:
Correct nut torque: 40 inch-pounds; 4.6 Newton-meters. TPMS SENSOR AND/OR VALVE BROKEN BY OVERTORQUE ARE NOT COVERED UNDER WARRANTY. FAILURE TO ACHIEVE THE NECESSARY TPMS SENSOR NUT TORQUE MAY RESULT IN AN INADEQUATE AIR SEAL, RESULTING IN TIRE AIR LOSS.
FCC Notice:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna-
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to the computer or peripheral devices.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
IC Notice: Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement:
This equipment complies with the RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm the radiator and your body.
WARRANTY INFORMATION
Professional installer: When replacing an entire TPMS sensor assembly under warranty, please complete the following TPMS sensor warranty information giving one copy to the Customer and send the duplicate copy to the indicated address.

Documents / Resources
![]() | BSI150511 TPMS Sensor |
References
- User Manualmanual.tools
